INSTALL_2005 - Laserfiche WebLink

Home Browse Search

Secondary' Containment Vacuum Sensing System Maximize protection with a vacuum _ a monitored secondary containment system . aw A Secondary Containment Vacuum Featunesand Benefits Facilitates periodic opetabilitytesting Sensing System for use with Veeder- Satis y Re uirements Leverage Existing Veeder-Root Systems to meet California's requuernent for Root's ATG Systems. The Secondary Uses STP asthevacutunsotureandworkswith Containment Vacuum Sensing (SCVS) �Z � Red jacket� sewndary space fortanksandlines JFESM as required by System is designed to detect leaks in double- . Satisfies the requ rernmts for(Lass I Leak Irt wm the SIP sump and c°nnects to the consoll e via intrinsically safe s`'iring walled tanks and piping systems while Detection as defined by the European . Able to share wiring conduit with other helping to contain a release of product while Standard EN 13160-2 Veciliff-Root intrinsically safe(LS)probes and 3rd Party,National Work Group and LGI 13 under vacuum.The system consists of: listed sensors including sump or line leak sensors. • interfaces to the Smart Serwr Interface with Reduce Exposure to Risk • Vacuum Sensors,connected to tank, Embedded Pressure Modem Alarms when vacuum cm-tot be maintained • Provides for positive shut down of pressurized sump or piping interstices or when replenish rate exceeds 85 liters per hour. lines when mquired. • A Submersible Turbine Pump(STP), . The Sys=alarms when liquid is detected in . Simple installation,no creed to mess with brine to provide a source of vacuum the secondary space • A Smart Sensor Interface with Embedded Pressure Module in a TLS-350 Operating Temperature Rating: Console Capability Monitoring System -25 degrees C to+70 degrees C The Vacuum Sensor is compatible with the following consoles: The Vacuum Sensor is interfaced to Veeder- Cable Length: Console 8 feet TLS-350R/EMC w/BIR" Root's TLS-350 Monitoring System via TLS-350 Plus/EMC Enhanced intrinsically safe wiring to provide system Sensor Dimensions: TLS-350/EMC status,replenish rate,alarm,and diagnostic 5'high x 5"wide 2"deep Upgrade Note:The Vacuum Sensor System requires the console to have version 24C software(or greater) information. along with an ECPU2 or ECPU w/NVMEM 1 board. Standard Models Vacuum Sensor Kits are available in a variety Veeder-Root P/N Description of models: 330020-467 4 Vacuum Sensor Kit'for steel tank 330020-468,-469,-470,-471 4 Vacuum Sensor Kit"for fiberglass tanks(4',6',8',10) 330020-486 4 Vacuum Sensor Kit"for no tank • For monitoring double-walled piping 330020-472 3 Vacuum Sensor Kit'for steel tank and sump interstices 33002G-473,-474,-476.-476 3 Vacuum Sensor Kit'for fiberglass tanks(4',6',8',10) • For monitoring double-walled steel tank 330020-485 3 Vacuum Sensor Kit"for no tank interstices(see back page) 330020-479 2 Vacuum Sensor Kit*for steel tank For double-walled fiberglass tanks 330020-481,-482,-483,-484 2 Vacuum Sensor Kit"for fiberglass tanks(4',6',8',10') • g 330020-480 2 Vacuum Sensor Kit'for no tank 857280-100 Vacuum Sensor for piping&sumps These kits differ in the number of vacuum 857280-200 Vacuum Sensor for steel tanks sensors and the configuration of associated 857280-301,-302,-303,-304 Vacuum Sensor for fiberglass tanks(4',6',8',10') liquid sensors.An inline kit mounted liquid 330020-448 Mounting Kit 332217-001 Relief Valve Assembly sensor is used for Vacuum Sensors 332250-001 Smart Sensor w/Embedded Pressure Sensor Module(7 Channel)" monitoring piping and sumps. An external Accessories Part Description Quanthy/Length Part Number liquid sensor(to be installed in the secondary 1/4"NPT Barbed Fittings 3 330020-487 space at the bottom of the tank) is provided 1/4"NPT Barbed Fittings 15 _330020-488 with one of the Vacuum Sensors in the steel 1/4"NPT Barbed Fittings 25 330020-489 and fiberglass tank kits to monitor the tank. Barbed Tee 1 576008-657 Vacuum Hose 25' 25' 332310-001 Vacuum Hose 50' 50' 332310-002 Vacuum Hose 100' 100' 332310-003 3-Way Ball Valve 1 576008-649 Kits include mounting bracket,6'of vacuum hose,relief valve assembly to required)and the appropriate number of liquid sensors, 3-way ball valves, barbed fittings and hose clamps so that each vacuum sensor can monitor a single tank,sump or piping interstices. The Vacuum Sensing System requires one 7 channel Smart Sensor Interface with Embedded Pressure Module,8 channel Smar Sensor Modules(p/n 329356-004)can be used for vacuum Sensors eight and above. For more information call: 1-888-561-7942 �� VEEDER-ROOT