|
(CARRIER MELS
<br /> PACKAGED ROOF TOP UNIT SCHEDULE (LO CODorna) OBESPECIFIED)
<br /> Oi EXHAUST FAN SCHEDULE HVAC CONTROL SETTINGS MECHANICAL SPECIFICATIONS
<br /> UNIT SYMBOL (NEW) �T (NEW) T (NEW) FAN NO. F EF EF
<br /> EACH HVAC UNIT SHALL BE PROVIDEDWITH 1. WORK INCLUDES INSTALLATION OF HVAC SYSTEMS, INCLUDING GREASE EXHAUST
<br /> FANS AND MAKE-UP AIR UNIT FOR KITCHEN HOODS SPACE HEATING/AIR
<br /> LOCATION ROOF ROOF ROOF LOCATION ROOF ROOF ROOF THERMOSTAT: CARRIER COMMERCIAL PROGRAMMABLE THERMOSTAT CONDITIONING SYSTEMS, SUPPLY, RETURN, EXHAUST,AND GREASE EXHAUST
<br /> OST T WITH DUCTWORK, GRILLES, REGISTERS, DIFFUSERS, COMPLETE CONTROLS SYSTEM, �Q~
<br /> KITCHEN GREASE KITCHEN GREASE REMOTE TEMPERATURE SENSOR. SEE SHEET M-100 FOR THERMOSTAT AND
<br /> W CFM 2,000(5 TON) 4,000(10 TON) 4,aoa(1a TON) AREA SERVED RESTROQMS SENSOR LOCATIONS,
<br /> INTERLOCK WIRING FOR OPERATION OF KITCHEN HOODS, EXHAUST FANS,AND
<br /> EXHAUST HOOD#1 EXHAUST HOOD#2 MAKE-UP AIR UNIT, DUCT INSULATION,AND RELATED ITEMS NECESSARY FOR A
<br /> FAN DUTY AIR EXHAUST AIR EXHAUST AIR EXHAUST ALL THERMOSTAT HAVE MA COMPLETE FUNCTIONING SYSTEM AS INDICATED ON THE PLANS, FURNISH ALL NEW
<br /> m o O s
<br /> TSP(IN W.G.) 0.6° 0.7" 0.7 5 SHALL HA MANUAL OVERRIDE. MATERIALS AND EQUIPMENT UNLESS NOTED OTHERWISE(U.N.O.).
<br /> TOTAL(BTUIHR) 57,320 112,160 112,160 FAN TYPE CENTRIFUGAL CENTRIFUGAL CENTRIFUGAL EACH UNIT CONTROL SHALL BE SET UP INITIALLY AS FOLLOWS:
<br /> BELT-DRIVEN BELT-DRIVEN DIRECT-DRIVEN 2. DRAWINGS FOR HVAC WORK ARE DIAGRAMMATIC, SHOWING THE GENERAL
<br /> z SENSIBLE(BTUIHR) 54,260 100,040 100,040 FAN ARRANGEMENT UPBLAST UPBLAST DOWNBLAST CONTRACTOR SHALL DETERMINE OCCUPIED PERIOD FROM OWNER. LOCATION, TYPE, LAYOUT AND REQUIRED EQUIPMENT, DRAWINGS SHALL NOT BE
<br /> SCALED FOR EXACT MEASUREMENTS. AS REQUIRED, REFER TO ARCHITECTURALG�
<br /> o - - - AND MANUFACTURER'S STANDARD INSTALLATION DRAWINGS FOR EQUIPMENT S� 01
<br /> c AMBIENT(F) 97 97 97 MIN.WHEEL DIAMETER FAN OPERATION SHALL BE CONTINUOUS DURING OCCUPIED PERIOD AND CONNECTIONS AND INSTALLATION REQUIREMENTS. FURNISH AND INSTALL
<br /> CYCLE WITH COOLING/HEATING DURING UNOCCUPIED PERIOD,
<br /> COIL ENTERING 64 WB/81 DB 64 W13/80 DB 64 WB/80 DB C.F.M. 3,450 3,450 450 DUCTWORK, CONNECTIONS, ACCESSORIES, OFFSETS, AND MATERIALS NECESSARY
<br /> PROGRAMMED SETPOINTS(FOR EACH THERMOSTAT): TO FACILITATE SYSTEM'S FUNCTIONING AS INDICATED BY THE DESIGN AND PANDA RESTAURANT GROUP INC.
<br /> v T.S.P. 1.25" 1.25" 0,25" COOLING OCCUPIED: 75°F• EQUIPMENT SHOWN ON PLANS. 1683 Walnut Grove Ave,
<br /> HEATING(BTUIHR) 120,000(INPUT)!98,000(OUTPUT) 180,000(INPUT) 148,000(OUTPUT) 180,000(INPUT)t 148,000(OUTPUT) z COOLING UNOCCUPIED: 85°F.
<br /> 2E Rosemead, California
<br /> B.H.P. 1.386 1.386 0.085 HEATING OCCUPIED: 68°F. 3. CODE COMPLIANCE: ALL WORK COVERED BY THIS SECTION SHALL BE IN
<br /> POWER SUPPLY 208V13Ph160HZ 208VI3®160HZ 208V13®160HZ w HEATING UNOCCUPIED: 50°F. ACCORDANCE WITH ALL LOCAL CODES AND ACCEPTABLE TO THE AUTHORITY 91770
<br /> HAVING JURISDICTION. Telephone: 626.799.9898
<br /> COMPRESSOR(RLA) 15.9 (2)15.9 (2) 15,9 FAN R.P.M. 1223 1223 1128 Facsimile:626.372.8288
<br /> a NOTE: DEVIATIONS FROM THE ABOVE MAY RESULT IN UNACCEPTABLE AIR
<br /> QUALITY, COMFORT AND/OR ENERGY CONSUMPTION. 4, COORDINATE WORK WITH OTHER TRADES, EQUIPMENT FURNISHED BY OTHERS AND
<br /> CONDENSER MOTOR(FLA) (1)1.4 (1)6.2 (1)6.2 MOTOR H.P. 2.0 2.0 D.25 OWNER REQUIREMENTS. PROVIDE DUCT RISES AND DROPS AS REQUIRED FOR
<br /> LU
<br /> INSTALLATION AND/OR TRADE COORDINATION. NOTIFY ARCHITECT OF ANY
<br /> LU EVAPORATOR MOTOR(FLA) 8.4 10.6 10.6 ELEC.CHARACTERISTICS 208V13PH160HZ 208V13PHI60HZ 115VI1PH160HZ DISCREPANCIES BEFORE STARTING WORK. WORK SHALL BE PERFORMED BY All ideas,designs,arrangement and plans indicated or
<br /> Q represented by this drawing are the property of Panda
<br /> I EXPERIENCED TRADESMEN AND THEIR WORK SHALL BE OF HIGH STANDARD
<br /> MIN,CIRCUIT AMPACITY 30.0,HACR=45 53.0,HACR=60 53.0,HACR=60 MOTOR R•P.M. AI R CURTAIN SCHEDULE Express Inc.and were created for use on this specific project.
<br /> ACCEPTABLE TO THE OWNER•
<br /> None of these ideas,designs,arrangements or plans may be
<br /> PRICING ORDERING AND DELIVERY BY CARRIER 48HCNA06A2M5 BY CARRIER 48HCDD12A2M5 BY CARRIER 48HCDD12A2M5 EQUIP. MFR/MODEL DESCRIPTION used by or disclosed to any person,firm,or corporation
<br /> MOTOR SPECIAL FEATURES OPEN DRIP-PROOF OPEN DRIP-PROOF OPEN DRIP-PROOF NS
<br /> DUCT SYSTEMS SHALL BE CONSTRUCTED,D, ITALLED, SEALED AND without the written
<br /> CONTACT;THERESA DAWSON DOWN DISCHARGE COMPLETE WITH DOWN DISCHARGE COMPLETE WITH DOWN DISCHARGE COMPLETE WITH permission of Panda Express Inc.
<br /> 1.VENTED ROOF CURB 1.VENTED ROOF CURB 1.ROOF CURB STD242-1 U-013 WEIGHT 65 LBS. PROVIDED BY PANDA EXPRESS
<br /> PHONE:949-309-9815 14"ROOF MOUNT CURB,ELECTRONIC 14"ROOF MOUNT CURB,ELECTRONIC 14"ROOF MOUNT CURB, ELECTRONIC MARS UNHEATED AIR CURTAIN (SERVICE DOOR). 115/1/60 5. INSULATED AS PROVIDED IN THE INT'L ENERGY AND MECHANICAL CODES, SHEET
<br /> MSA
<br /> E-MAIL: PROGRAMMABLE THERMOSTAT, PROGRAMMABLE THERMOSTAT, PROGRAMMABLE THERMOSTAT, 2.HINGED AND CHAINED 2•HINGED AND CHAINED 2.BAGKDRAFT DAMPER METAL SHALL BE IN ACCORDANCE WITH ASHRAE AND SMACNA STANDARDS. SHEET
<br /> Theresa.Dawson@carrier.utc.com ENTHALPY ECONOMIZER WITH ENTHALPY ECONOMIZER WITH ENTHALPY ECONOMIZER WITH ACCESSORIES FAN INSTALLATION FAN INSTALLATION QUICK-SERV AIR CURTAIN (WINDOW NON-HEATED). 120/1160, 20 AMP METAL SHALL BE GALVANIZED OF LOCK-FORMING QUALITY, ASTM A-525. UNLESS
<br /> M9A
<br /> BAROMETRIC RELIEF. BAROMETRIC RELIEF. BAROMETRIC RELIEF. CF-25 WEIGHT 30 LBS
<br /> COMB.FAN MOTOR 0.48 AMPS(DOES COMB. FAN MOTOR 0.48 AMPS(DOES COMB.FAN MOTOR 0.48 AMPS(DOES FOR DUCT ACCESS FOR DUCT ACCESS REFERENCE ARCHITECTURAL WINDOW SCHEDULE FOR OTHERWISE NOTED, DUCT DIMENSIONS ON DRAWINGS ARE NET INSIDE CLEAR
<br /> DIMENSIONS ON LINED DUCTS OR SHEET METAL DIMENSIONS ON UNLINED DUCTS. REVISIONS:
<br /> NOT OPERATE WITH COMPRESSOR). NOT OPERATE WITH COMPRESSOR). NOT OPERATE WITH COMPRESSOR). CAPTIVEAIRE CAPTIVEAIRE CAPTIVEAIRE HEATED OR NON-HEATED UNIT. PROVIDED BY GC. ALL ANGLE IRON USED FOR SUPPORT SHALL BE GALVANIZED. ROUND RIGID
<br /> OPER.WT. :895 LBS APPROX. OPER.WT. : 1504 LBS APPROX. OPER.WT. : 1504 LBS APPROX. MANUFACTURER MODEL:NCAI6FA MODEL:NCAI6FA MODEL:DD7FA DUCTWORK SHALL CONFORM TO SMACNA TABLE 3-2.
<br /> SEER=15.00 EER=12.5,AFUE=82% SEER=NIA EER=11.5,AFUE=82% SEER=NIA EER=11.5,AFUE=82% NOTES:
<br /> WT.197 LBS WT, 197 LBS WT. 113 LBS
<br /> ALL ITEMS RELATED TO HVAC SYSTEM SHALL BE PROVIDED AND INSTALLED BY CONTRACTOR,CONTACT CARRIER REPRESENTATIVE ABOVE. INSTALL ACCORDING TO MANUFACTURER'S INSTRUCTIONS. 6. INSTALL DUCT HIGH AS POSSIBLE WITHIN JOIST SPACE. CONSULT ARCHITECT AND
<br /> THERMOSTATS:REMOTE SENSOR TYPE,2417 PROGRAMMABLE AND CAPABLE OF OPERATING ROOFTOP UNITS AND ACCESSORIES"CARRIER"COMFORT PRO ENGINEER FOR ALTERNATE ROUTING IF CONFLICT OCCURS.
<br /> 33CS PROVIDE REMOTE SENSOR FOR EACH THERMOSTAT NOTES: MECHANICAL LEGEND
<br /> DUCT MOUNTED SMOKE DETECTORS: IONIZATION TYPE/UL LISTED,CSFM CERTIFIED,24 VAC, BY EDWARDS, DH HOUSING WITH 1551 F SENSOR 7• SEAL ALL TRANSVERSE AND LONGITUDINAL DUCT SEAMS AIR-TIGHT. PROVIDE
<br /> NOTE: 1. KITCHEN EXHAUST FANS SHALL BE ELECTRICALLY TURNING VANES AT ALL ELBOWS OR OFFSETS EXCEEDING 30 DEGREES.
<br /> 1. 1.9 AMPS(5 TON)AND 3.8 AMPS(7.5 AND 10 TON)ECONOMIZER INCLUDED IN ELECTRICAL TOTAL MCA PER MANUFACTURER'S LITERATURE. INTERLOCKED WITH MAKE-UP AIR UNIT AND ROOFTOP UNITS. SYMBOL ABBREVIATION DESCRIPTION
<br /> 2. UNIT WEIGHTS ABOVE INCLUDE ACCESSORIES AND CURB. 8. GREASE EXHAUST SYSTEM:ALL GREASE EXHAUST DUCTS SHALL BE FABRICATED BY
<br /> 3. FACTORY OPTIONS SHALL INCLUDE HAIL GUARD PROTECTION FOR ALL UNIT. 2. FOR WIRING DIAGRAM SEE 5IM-501 WELDED JOINT CONSTRUCTION OF 16 GAUGE WELDED STEEL OR 18 GAUGE
<br /> 4. FACTORY OPTIONS SHALL INCLUDE FACTORY INSTALLED DISCONNECTS AND CONVENIENCE OUTLETS(FIELD POWERED REFER TO ELECTRICAL DRAWING). ABV ABOVE
<br /> 5. PROVIDE THRU THE BASE ELECTRICAL CONNECTION KIT##CRBTMPWR002A01 FOR ALL UNITS. STAINLESS STEEL. PROVIDE RATED ACCESS DOORS AT ALL ELBOWS AND OFFSETS ISSUE DATE:
<br /> AFF ABOVE FINISHED FLOOR NECESSARY FOR COMPLETE CLEANING OF GREASE DUCT. PROVIDE MINIMUM 30"00" 02.18.19 ISSUED FOR PERMIT
<br /> UNOBSTRUCTED ACCESS OR ROUTE FROM THE CEILING TO EACH ACCESS DOOR. DO
<br /> DE&GN NOTE:_ I NOT BLOCK ACCESS WITH PLUMBING, ELECTRICAL OR HVAC OBSTRUCTIONS. ALL
<br /> I CLG CEILING
<br /> SEE MODEL SPACE ON M , 1Ot? ELBOWS SHALL BE LONG RADIUS. GREASE DUCT SHALL BE INSTALLED EITHER IN A
<br /> MAKE-UP AIR UNIT SCHEDULE
<br /> FOR MAKE-UP AIR DESIGN DN DOWN RATED ENCLOSURE PROVIDED BY THE GENERAL CONTRACTOR OR WRAPPED WITH
<br /> PARAMETERS FIREMASTER GREASE DUCT WRAP,
<br /> MARK MFR/ MODEL LOCATION SERVICE GAS HEAT TYPE COOLING CFM ESP MOTOR REMARKS ® z DUCT SECTIONS(SUPPLY, ExHAusr,RETURN) 9. DUCT INSULATION: PROVIDE DUCT WRAP FOR ALL DUCTS ABOVE CEILING, INCLUDING
<br /> AREA VERTICAL, HORIZONTAL, RIGID AND FLEXIBLE DUCTS, EXCLUDING PREFABRICATED
<br /> GAS FIRED MAKEUP AIR UNIT W/38AUD 10 TON, DUAL CIRCUIT AIR FLEXIBLE DUCT PREINSULATED DUCTS AND GREASE DUCTS. DUCT WRAP SHALL BE JOHNS MANVILLE
<br /> INPUT: 407,160
<br /> DIRECT FIRE GAS COOLED CONDENSING UNIT. REFER TO SHEET M-402 FOR MVD MANUAL VOLUME DAMPER MICROLITE OR EQUAL WITH FOILISCRIM/KRAFT, 1 IN THICKNESS, 1.5 POUNDSIFT3
<br /> �
<br /> KITCHEN BTHU
<br /> HEATED, DUAL CIRCUIT 5 HP
<br /> DX INFORMATION. 4-5 WEEK LEAD TIME. SHIPPING INCLUDED IN DENSITY. DUCT WRAP SHALL BE BONDED GLASS FIBERS IN THERMOSETTING RESIN
<br /> MAU1 CAPTIVEAIRE A3-G18 ROOF-TOP HOOD#1  OUTPUT: 374,587 COOLED SUPPLY, DX COIL 5'520 0.75" 208V/3PH/60HZ PRICE. SHIPS FROM TYLER, TX. SHIPS SEPARATE, FREIGHT MEETING NFPA 90A,WITH K VALUE NOT TO EXCEED 0.23 AT 75 DEGREES F. FLAME DRAWN BY:
<br /> BTHU DOWN INCLUDED. NOTE: FACTORY OPTIONS SHALL INCLUDE OBD OPPOSED BLADE DAMPER SPREAD AND SMOKE DEVELOPED RATINGS SHALL NOT EXCEED 25150. APPLY 100%
<br /> DISCHARGE NONCORROSIVE COATING AND HAIL GUARD PROTECTION. ADHESIVE COVERAGE TO SHEET METAL DUCTWORK, PROVIDE ADDITIONAL
<br /> MFR MANUFACTURER MECHANICAL FASTENERS ON DUCTS OVER 12"WIDE OR 16" HIGH. MECHANICAL
<br /> FASTENERS SHALL BE"GRIPNAIL" OR WELDED PIN AND SPEED CLIPS SPACED PER PANDA PROJECT#: D6609
<br /> MIN MINIMUM SMACNA STANDARDS..
<br /> DIFFUSER & GRILLE SCHEDULEARCH PROJECT#: PRG18003
<br /> OSA OUTSIDE AIR 10. FLEX DUCT: PROVIDE FACTORY ASSEMBLED CLASS 1 AIR DUCT(UL 181) WITH
<br /> FIBERGLASS INSULATION AND REINFORCED OUTER PROTECTIVE COVER/VAPOR
<br /> 1 ROUND RIGID DUCTWORK BARRIER. FLEX DUCT SHALL MEET NFPA 90A WITH FLAME SPREAD UNDER 25, SMOKE
<br /> DESIGNATION MANUFACTURER MODEL NO TYPE COLOR NOM NECK SIZE NOM FACE SIZE FRAME TYPE NC MAX REMARKS DEVELOPED UNDER 50 AND SHALL BE RATED FOR 2"W.C. PRESSURE AND 0 TO 250
<br /> TSP TOTAL STATIC PRESSURE DEGREE TEMPERATURE. FLEX DUCT MAXIMUM ALLOWED LENGTH TO BE PER LOCAL
<br /> A PRICE PDMC3-R6 PERFORATED MODULAR CORE WHITE 14"0 24"x 24" LAY-IN T-BAR < 30 ROUND NECK BUTTERFLY VOLUME DAMPER CODE,
<br /> 8 PRICE PDMC3-AFI PERFORATED MODULAR CORE 8-12 12"0 16"x 16" SURFACE < 3q ROUND NECK BUTTERFLY VOLUME DAMPER `' TURNING VA# ES MECHANICAL&PLUMBING
<br /> WHITE JOHN 51SK, ENGINEER
<br /> C PRICE PDMC3-AFI PERFORATED MODULAR CORE 8-12 9" x 9" 12"x 12" SURFACE < 30 SQ. TO RD. DUCT ADAPTER FOR DIA. A5 SHOWN, OPPOSED BLADE DAMPER 11. PROVIDE INSULATION APPLIED TO COMPLETE BACKPAN OF AIR DEVICES.
<br /> WHITE IDSTUD104
<br /> H-12 I. 1E CONSTRUCTION NOTES
<br /> D PRICE PDDR3 PERFORATED RETURN WHITE 22 x 22 24 x 24 LAY-IN T-BAR < 35 1431 GREENWAY DRIVE#510
<br /> E PRICE PDDR3-AFI PERFORATED RETURN 12. ACCESS DOOR: PROVIDE HINGED ACCESS PANELS IN DUCTWORK WHERE SHOWN
<br /> wH�TE 10" DIA. 12"x 12" SURFACE WITH VOLUME CONTROLLER EF IRVING,TX 75038
<br /> F PRICE PDDR3 PERFORATED RETURN WHIT 22"X22" 24"x 24" LAY-IN T BAR <35 MECHANICAL EQUIPMENT DESIGNATION AND AS REQUIRED FOR ACCESS TO DAMPERS OR EQUIPMENT. PROVIDE INSULATED
<br /> 1 T:972.870.1288
<br /> BRONZE ACCESS DOORS IN INSULATED DUCTWORK.
<br /> G PRICE AS210 LINEAR SLOT T_T7WHITE 2 6" OVAL 1 SLOT SURFACE < 35 SEE PLAN FOR LENGTH, PROVIDE WITH FACTORY PLENUM O SMOKE DETECTOR E:JSISK@IDSTUD104.COM
<br /> H PRICE PDMC3-R6 PERFORATED MODULAR CORE BRONZE 14"x 14" 24"x 24" LAY-IN T-BAR < 30 SQ. TO RD. DUCT ADAPTER FOR DIA.AS SHOWN 13. AUTOMATIC TEMPERATURE CONTROL: CONTRACTOR TO PROVIDE AND INSTALL 2417
<br /> BRONZE THERMOSTAT/UNIT PROGRAMMABLE THERMOSTATS AND REMOTE SENSORS,
<br /> J PRICE PDMC3-AFI PERFORATED MODULAR CORE WHITE 8"0 24"x 24" LAY-IN T-BAR <30 OPPOSED BLADE DAMPER 0 1
<br /> �L% REMOTE SENIOR I UNIT 14. KITCHEN HOOD EQUIPMENT INTERLOCK: PROVIDE ALL INTERLOCK AND CONTROL
<br /> NOTE: PROVIDE FACTORY INSTALLED BACK PAN INSULATION ON AIR DEVICES. '�`J 1 WIRING FOR KITCHEN HOOD SYSTEMS, WHICH INCLUDES EF1, EF2, MAU1 AND ANSUL
<br /> HVAC CONTRACTOR IS TO PURCHASE ALL AIR DEVICES FROM PANDA APPROVED NATIONAL ACCOUNT VENDOR THERMAIR SYSTEMS INC. SYSTEM SHUT DOWN INTERLOCK TO MAKE-UP AIR FAN. UPON ACTIVATION OF ANSUL
<br /> PLEASE CONTACT RON CAMPTON AT 602-705-5010 OR EMAIL ronc@thermairsystems.com SYSTEM, MAKE-UP AIR FAN SHALL BE DEACTIVATED. PROVIDE ALL NECESSARY
<br /> CONTROLS AND WIRING FOR A COMPLETE AND OPERABLE SYSTEM. INTERLOCK
<br /> GREASE EXHAUST FANS AND MAKE-UP AIR UNIT TO START SIMULTANEOUSLY FROM
<br /> AIR BALANCE SCHEDULE OSA VENTILATION CALCULATION SWITCH PROVIDED AT HOOD.
<br /> ITEM 9 SUPPLY AIR RETURN AIR MAKE-UP AIR EXHAUST OSA REQ.'D FOR 15. TEST AND ADJUST EACH PIECE OF EQUIPMENT AND EACH SYSTEM AS REQUIRED TO
<br /> TOTAL OCCUPANCY TOTAL OSA SQ.FT. OSA REQ.`D THIS OCCUPANCY ASSURE PROPER AIR BALANCE AND OPERATION. PROVIDE A CERTIFIED AIR BALANCE
<br /> AREA TYPE AREA DENSITY 2 OCCUPANTS PER SM) PER PER)ON CLASSIFICATION REPORT TO OWNER SHOWING DESIGN AND MEASURED AIR VOLUMES, STATIC
<br /> MAUI 0 0 +5,520 0 (FT� (PEOPLEIFT. ) (CFM) (CFM)
<br /> (CFM) PRESSURES, FAN RPMS, ETC. AIR BALANCE CONTRACTOR SHALL ADJUST SYSTEMS
<br /> EF-1, EF-2 0 0 0 -3,450 x 2 HALLWAYS 26 - 0.06 - 2 TO MINIMIZE NOISE AND VIBRATION,AND TO ASSURE PROPER FUNCTION OF
<br /> RTU-1 +2,000 -1,500 500 0 CONTROLS, MAINTENANCE OF TEMPERATURE AND OPERATION, GENERAL
<br /> STORAGE 149 - - 0.15 - 22 CONTRACTOR TO OBTAIN ALL INSPECTIONS REQUIRED BY LOCAL CODE AND
<br /> RTU-2, RTU-3 +4,000, +4000 -3,250, -3,250 2@750 EA 0GUARANTEE WORK AND INSTALLATION FOR ONE YEAR AFTER ACCEPTANCE BY PANDA EXPRESS
<br /> KITCHEN 84-8 2011,000 12 - 15 180 OWNER. GENERAL CONTRACTOR TO FURNISH OWNER WITH TWO COMPLETE SETS
<br /> EF-3 - - _ -450 DINING ROOM 1109 7011,000 78 - 20 1560 OF AS-BUILT DRAWINGS INDICATING ALL INSTALLED WORK, INCLUDING ALL CONTROL
<br /> WIRING DIAGRAMS AND INTERLOCK FOR SYSTEM OPERATION. WARM & WELCOME V3
<br /> TOTAL +10,000 -8,000 +7,520 -7,350 VENTILATION SHALL BE BALANCED BY AN APPROVED METHOD. TOTAL OSA REQUIRED FOR THIS 1422 WEST COLONY ROAD
<br /> CFM
<br /> A BALANCE REPORT SHALL VERIFY THAT THE VENTILATION TENANT(CFM) 1'64 16. CONTRACTOR SHALL BE RESPONSIBLE FOR INSTALLATION OF ECONOMIZERS RIPON, CALIFORNIA 95366
<br /> BUILDING PRESSURE _ +170
<br /> 1 7Q CFM IS CAPABLE OF
<br /> BY SECTION 40UPSA SAID REPORT MUSO BE PRESENTED TOTAL OSA PROVIDED 2p00 INCLUDING INSTALLATION OF ALL NECESSARY SENSORS AND CONNECTIONS TO
<br /> THERMOSTAT. PROVIDE SUPPORT OF ECONOMIZERS PER MANUFACTURER'S
<br /> BALANCE TOLERANCES AS FOLLOWS: TO THE ADMINISTRATIVE AUTHORITY. (CFM) REQUIREMENTS AND TEST FOR PROPER OPERATION PRIOR TO FINAL TEST AND
<br /> KITCHEN EXHAUST HOODS: 0%TO +10% BALANCE.
<br /> OUTDOOR AIR: 0%TO+10%
<br /> SUPPLY&RETURN DIFFUSERS: ±10%
<br /> TOILET EXHAUST: ±10%
<br /> BALANCE RTU SUPPLY AND RETURN PRIOR TO TURNING ON EXHAUST FANS.
<br /> KITCHEN EXHAUST FANS SHALL BE BALANCED WITH VELOCITY MATRIX OR A 4"ANEMOMETER M �000
<br /> MECHANICAL NOTES
<br /> SPECIFICATIONS & SCHEDULES
<br /> WARM &WELCOME V3
<br />
|