|
- HOOD ELECTRICAL PLAN NOTES
<br />DIVISION 16 - GENERAL ELECTRICAL -
<br />GENERAL
<br />1 INSTALL ALL ELECTRICAL IN THIS WORK PER LATEST NEC AND CITY OF STOCKTON BUILDING DEPT.
<br />REQUIREMENTS. FLEXIBLE CONDUIT MAY BE USED BUT MUST CARRY GROUND WIRE TO BOX. SWITCH
<br />LIGHTING AS INDICATED ON DRAWINGS. ALL CIRCUITS SHALL BE MARKED TO INDICATE AREAS SERVED.
<br />PROVIDE ADDITIONAL CIRCUITS AS REQUIRED BY OTHER TRADES. GENERAL ELECTRICAL MAYBE RUN IN
<br />FLEXIBLE METAL CONDUIT, MC OR EMT. SETSCREW FITTINGS ON EMT. MC CABLE TO USED IN CONCEALED
<br />WALL OR CEILING. INSTALL ALL FIXTURES PER MFG REQ. USE ONLY APPROVED AND LISTED EQUIPMENT.
<br />CONDUCTORS SHALL BE COPPER CONDUCTORS TYPE THWNITHHN. USE CONNECTORS APPROVED FOR
<br />RELATED WIRE SIZE. THE USE OF STRANDED OR SOLID APPROVED. USE STRANDED FOR SIZES #8 OR
<br />LARGER
<br />3. ALL WORK SHALL CONFORM TO THE CEC 2013 EDITION AND TO THE APPLICABLE REQUIREMENTS OF LOCAL,
<br />STATE, AND FEDERAL CODE(S) AND/OR AGENCIES HAVING JURISDICTION; AND SHALL TAKE PRECEDENCE
<br />OVER WORK SHOWN. ANY DISCREPANCIES SHALL BE BROUGHT TO THE ATTENTIONOF THE DESIGNER
<br />PRIOR TO THE INSTALLATION OF WORK.
<br />4 ELECTRICAL CONTRACTOR SHALL VERIFY DIAGRAMMATIC LAYOUT OF ELECTRICAL WORK WITH OWNER
<br />PRIOR TO INSTALLATION.
<br />5• SEE ELECTRICAL SYMBOLS, VERIFY ALL SYMBOLS AND CONDITIONS AS REQUIRED PRIOR TO INSTALLATION.
<br />JOB CONDITIONS
<br />ELECTRICAL DRAWINGS: THE ELECTRICAL DRAWINGS, AS CONTAINED, ARE ESSENTIALLY
<br />6. DIAGRAMMATIC AND ALTHOUGH THE SIZE AND LOCATION OF EQUIPMENT ARE SHOWN TO SCALE
<br />WHEREVER POSSIBLE CONTRACTOR SHALL MAKE USE OF ALL DATA AND VERIFY THIS
<br />INFORMATION AT THE BUILDING SITE. THE DATES INDICATED ON THE DRAWINGS AND IN THE
<br />JOB CONDITIONS AND DECISIONS OF THE DESIGNER WILL GOVERN EXACT LOCATIONS,
<br />DISTANCES, LEVELS, AND OTHER CONDITIONS.
<br />OPERATION:
<br />7 THE SYSTEM SHALL BE COMPLETE AND FULLY FUNCTIONING TO THE SATISFACTION OF THE DESIGNER AND
<br />THE OWNER. INSTALL ALL CIRCUITS, J-BOXFS, WIRING DISCONNECTS AND ANY OTHER EQUIPMENT NEEDED
<br />TO PROVIDE ELECTRICAL SERVICE FOR SIGNAGE.
<br />g. DRAWINGS -
<br />THE LAYOUT OF LIGHT FIXTURES ARE TO BE DIVIDED IN THE ROOM AS SHOWN ON THE PLANS. ANY Questions
<br />ABOUT LAYOUT SHOULD BE DIRECTED TO THE ENGINEER. UPON COMPLETION OF THE INSTALLATION,
<br />FURNISH A SET OF 'RECORD' (AS -BUILT) DRAWINGS TO THE DESIGNER CLEARLY MARKED WITH THE
<br />CHANGES AUTHORIZED DURING CONSTRUCTION, CUTTING NOTCHING DRILLING CONTRACTOR SHALL BE
<br />RESPONSIBLE FOR ALL WORK HEREIN INCLUDING CUTTING, BORING, NOTCHING, FURRING AND DRILLING AS
<br />NECESSARY TO COMPLETE THIS PROJECT. "NOTE: NO CUTTING, BORING, NOTCHING, FURRING AND
<br />DRILLING OF TRUSS OR OTHER STRUCTURAL MEMBERS WILL BE ALLOWED. CONTRACTOR SHALL
<br />COORDINATE WITH OTHER TRADES TO ALLOW FOR GROUP RUNS AND ELIMINATE ANY OVERLAPPING OR
<br />OBSTRUCTION.
<br />9.
<br />WORKING CLEARANCES
<br />WORKING CLEARANCE REQUIREMENTS FOR ALL ELECTRICAL EQUIPMENT INCLUDING DISCONNECTS WILL BE
<br />MAINTAINED AS PER CEC 2010 ARITCLE 110.26
<br />10 COMPLETION OF WORK AND TEST
<br />THE ENTIRE ELECTRICAL SYSTEM SHALL BE FREE FROM ANY SHORT CIRCUITS, AND IMPROPER GROUNDS.
<br />DEMONSTRATE WITH THE OWNER AND DESIGNER THAT THE ENTIRE INSTALLATION IS COMPLETE AND IN
<br />PROPER OPERATING CONDITION.
<br />i
<br />1. Dur;ng i of -,nal operation, both exhaust -fan
<br />ant MaKeup a in on position
<br />20 When Ansel Sys tem is acUva+ed, make up
<br />air hooch lights c:nd all elect{ ice devices VV '11
<br />the hood Will be cuterrc-Jtically -1.ur-ned Off.
<br />H 0 0 D E X I A lil/ I- I_ A U 0 ISI A C �! Y B E
<br />LJRN!ED 0, all elec;tri!;;a e guipmen-T, dev1ce S,
<br />receptacles, lighting; etc. to be loca Led within
<br />and under i.he hood footprint.
<br />All receptacics (net,,, and existing) in all
<br />l
<br />kitchen food prep areas siia'll be GFC
<br />prote(-ted.
<br />FastlWraW"k' XL
<br />AJ Them I Cemmics
<br />C4mmer ia[ Kitchen Grease Duct Enclosure System
<br />Air Ventilation Duct Ertctosure Systettt
<br />f res:op art rated Rocr and wail assemblies FastWrap XL as UL
<br />%IaGsilted and is port Df Lit.'s Lis;itig and Foilow-Up Service
<br />Program to ensure the •;c-nilstent g%iahty essential to the criti-
<br />cal nature of this fife -safety application..
<br />Product Features
<br />• Zero clearance to ceni"vtibles at anY locaticn
<br />Thin and Lightweight at 1-1)2 inch think, 6 pc.f density
<br />• Contours easily to complex duct designs
<br />•
<br />Buttjointson Inside layer • Aa'rd labor, space, 3rd rAater,a:
<br />• Fully rail encapsulated for fast and clean installation
<br />Completely inorganic and non-aornbustiiaie
<br />Contains 2C@0°F rated I bees For added safety margin
<br />Contains na loin temperature rninerai or glass fibers
<br />Wide variety of through penetration systems
<br />Resistant to mold growth
<br />• Extensive Listings and dat1114d installahon irstn:cticn.s
<br />Oftrereel in 60 and 100 square fact roils
<br />Available in 48 inch widths for less joints and installation
<br />labor
<br />Reference Standard Standard No.
<br />Pe-rformance
<br />Prcduot Data & Instaflatiort Guide
<br />pass
<br />t. Froiluct Description
<br />Pass
<br />6Cerarritls' new FlreMaster ;:MtVlrir '9L is the
<br />Pass
<br />tta;en"t and lightest flexible wrap rnaterial.availaiaie tat pass-
<br />$
<br />es the AS -T64 E 2335 test:standard required by the 2000 IMC
<br />Pass
<br />and NFPA Lad for reduced ctearaneo enclosure matonals used
<br />Pass
<br />io provide I or 2 hour fire rating for kitchen exhaust ducts.
<br />_
<br />f'astWrap XL is alas VL Ctassiried and Labe:ed per 130 0944
<br />5�v
<br />a9 ar alternative to a t or 2 hour rated e-nciosure for air vent!-
<br />lation ducts The FaslWrap XL core blan$iet is manufactomd
<br />4 2s :h
<br />using Thermal Ceramics patented Suyerwooil� fiber. a 2400'F
<br />Res'str:
<br />rated, non-comt)u%tita!e, slkar:rte-earth 34:1icata wool with low.
<br />Pass
<br />biopersistence. FastWrap XL is the product of extensive
<br />Pass
<br />rosoarch and developrnont resuhing In break•thrcugh improva-
<br />. N...,x
<br />rnents in stgodicart tnhancerrnerts
<br />in thermal properties beneficial to Eire protection apptleatiOns-
<br />PastWrap XL when u*eti in t:vmbin,atlon with an approved
<br />q;rostop sealant provides an o"ective through penetration
<br />A. Performance 5peciCnations
<br />f res:op art rated Rocr and wail assemblies FastWrap XL as UL
<br />%IaGsilted and is port Df Lit.'s Lis;itig and Foilow-Up Service
<br />Program to ensure the •;c-nilstent g%iahty essential to the criti-
<br />cal nature of this fife -safety application..
<br />Product Features
<br />• Zero clearance to ceni"vtibles at anY locaticn
<br />Thin and Lightweight at 1-1)2 inch think, 6 pc.f density
<br />• Contours easily to complex duct designs
<br />•
<br />Buttjointson Inside layer • Aa'rd labor, space, 3rd rAater,a:
<br />• Fully rail encapsulated for fast and clean installation
<br />Completely inorganic and non-aornbustiiaie
<br />Contains 2C@0°F rated I bees For added safety margin
<br />Contains na loin temperature rninerai or glass fibers
<br />Wide variety of through penetration systems
<br />Resistant to mold growth
<br />• Extensive Listings and dat1114d installahon irstn:cticn.s
<br />Oftrereel in 60 and 100 square fact roils
<br />Available in 48 inch widths for less joints and installation
<br />labor
<br />Reference Standard Standard No.
<br />Pe-rformance
<br />Creast Duct Enclosure System ASTM i;.Z:30
<br />pass
<br />2,ect .• t8 l - .`on- A:T1.1 r— .t..
<br />G'OiY.lrStllvtl'ty
<br />Pass
<br />Ressance AaTM E,i'a
<br />iwail'i
<br />Pass
<br />Esct:a*. `6.3 - Durab,lny 7+s; AwTM 'MA
<br />Pass
<br />Seen t5-< - "aural Fire Test ASTM c'.'3 6
<br />Pass
<br />rire Enii ^i
<br />-duck ASTMc' 4E`I�
<br />Pass
<br />Surface Burning [IiaiaLOFfI5t1Gs
<br />F dint Spead ii¢%'blar:hetl ASTM E54
<br />5�v
<br />_rrroke Develoce4 A3TM EEA
<br />T-hemal es!stance iR-v«tue ASTtS .'fi 10
<br />7D'F)
<br />4 2s :h
<br />Maid Grow* 17556 -95% A,TM D9328
<br />humidity)
<br />Res'str:
<br />Air Ventilation must Enelasure 1 :� 11 4
<br />Pass
<br />Grease timet Enclosure System JUL t97,S'
<br />Pass
<br />nrr'M.•r .wt -I rY�. ni. r., ,k err .-M1-.s x•YNr-,. �.'�ernu
<br />. N...,x
<br />2. Applications
<br />• Applied in 2 layers to provide i or hour fire protection to
<br />grease ducts exhausting Type t hoods per 2006 WC. Nr FA S LtstiegsiMuitding Cndk Reports
<br />0 and 2006 IAPMO. UMC
<br />• Applied in t Payer as an akematwe to a T or 2 hour rated
<br />sled uses
<br />eri,60sure for air Ventilation oucis
<br />3. Phy5imai Charaoteristias
<br />Product
<br />;Unrt Sixe
<br />UnitlI YVf.7
<br />Can- Ctrt.
<br />Fs56� ry Xi
<br />li '1-1:C^ N 24, X �5'
<br />1 37 $1L�.
<br />Fast"Nran Y1.
<br />Rall t. 1''^ a �i v 24'
<br />1 7 Ebs.
<br />Fasr4'nno X� Cotiar
<br />Rall I-tf=' s d' , `b'
<br />4 37 ° lbs.
<br />Caor
<br />White btankel rrilh stwi'nil enaapstAafca
<br />Li
<br />Agency
<br />11511119
<br />`.'i5$ Duct f',nV1'J'iu re .o}fS:iiT: i�STC
<br />Ieara�l�e} - AC I � -, ;F.3T)A E2:tir2s
<br />AREA LOAD 112
<br />v.-jra5*Duct Enc fas.fe::ySxm?Zerc
<br />uk,JxJ trej -AF7,M E2?3''
<br />IGC -E,'
<br />G3:R22!,;
<br />Throuin?eretaacmEireS;opSy-ter^-ASTM1j,L
<br />cc.4; L
<br />5•seF!gWii
<br />VenS3tan Duct Eerdosum System - ISO 6P.4
<br />[JL
<br />J' 3
<br />91411 n!A CToi ItITI IDAI 11tH TC.viii
<br />STRUCTURAL CALCULATION HOOD 'I
<br />TRIBUTARY AREA: 114 (4 HANGING ANGLES, 1 AT EACH
<br />CORNER)
<br />HOOD LOAD: 449 LBS TOTAL
<br />280 LBS (TOTAL HOOD WEIGHT) / 4 (TRIBUTARY AREA) = 112 LBS PER THREADED ROD
<br />112 LBS < 60,000 LBS (THREADED ROD TENSILE STRENGTH CAPACITY) = OK
<br />0
<br />TRIBUTARY
<br />AREA LOAD 112
<br />LBS PER BOLT
<br />4
<br />0
<br />�— MANUFACTURERS HOOD
<br />HANGING ANGLES. SEE HOOD
<br />DRAWINGS, SHEET H1
<br />HOOD WEIGHT
<br />DISTRIBUTION DIAGRAM
<br />STRUCTURAL CALCULATION HOOD 2
<br />TRIBUTARY AREA: 114 (4 HANGING ANGLES, 1 AT EACH
<br />CORNER)
<br />HOOD LOAD: 564 LBS TOTAL
<br />564 LBS (TOTAL HOOD WEIGHT) 14 (TRIBUTARY AREA) = 112 LBS PER THREADED ROD
<br />141 LBS < 60,000 LBS (THREADED ROD TENSILE STRENGTH CAPACITY) = OK
<br />0
<br />TRIBUTARY
<br />AREA LOAD 141
<br />LBS PER BOLT
<br />o
<br />O
<br />- HOOD DETAIL'S
<br />SCALE: 1" = V-0"
<br />MANUFACTURERS HOOD
<br />HANGING ANGLES. SEE HOOD
<br />DRAWINGS, SHEET H1
<br />-• — HOOD WEIGHT
<br />DISTRIBUTION DIAGRAM
<br />- (E) ENGINEERED
<br />WOOD TRUSSES
<br />(3) TOTAL DIAGONAL
<br />STEEL L1 -112x1 -112x3116
<br />WELDED SOLID
<br />FRAMES (1 EACH
<br />SHORT END AND 1
<br />ACROSS FRONT OF
<br />HOOD)
<br />APEX
<br />ARCHITECTURE
<br />845 S. Commerce Street
<br />Stockton, CA. 95206
<br />(209) 662-4874
<br />apexplanning@hotmail.com
<br />Steven Anthony Torres II
<br />Architect # C32553
<br />PROPERTY OWNER
<br />Francisco Javier Llamas
<br />CONTRACTOR
<br />tbd
<br />EL GRULLITO
<br />RESTAURANT T.I.
<br />STOCKTON
<br />1687 N. Californian Street, Suite #3
<br />Stockton, CA. 95204
<br />HOOD DETAILS
<br />AR
<br />EIC# C 32553
<br />REN. 3-31 j9/s
<br />�p �
<br />fi c -
<br />REV.# HATE tSSUED DESCRIPTION
<br />APEX PROJECT 18-19
<br />DATE:10-14-2018
<br />All
<br />DATE Copyright APEX
<br />
|