|
ACCESSIBILITY NOTES (CONT.)
<br /> CURB RAMPS (CONT.) PARKING CONT. LAVATORIES CONT.
<br /> 11B-406.5.1 LOCATION. CURB RAMPS AND THE FLARED SIDES OF CURB RAMPS "UNAUTHORIZED VEHICLES PARKED IN DESIGNATED ACCESSIBLE SPACES NOT 11B-606.5 EXPOSED PIPES AND SURFACES. WATER SUPPLY AND DRAIN PIPES �r
<br /> SHALL BE LOCATED SO THAT THEY DO NOT PROJECT INTO VEHICULAR TRAFFIC DISPLAYING DISTINGUISHING PLACARDS OR SPECIAL LICENSE PLATES ISSUED UNDER LAVATORIES AND SINKS SHALL BE INSULATED OR OTHERWISE
<br /> LANES, PARKING SPACES, OR PARKING ACCESS AISLES. CURB RAMPS AT MARKED FOR PERSONS WITH DISABILITIES WILL BE TOWED AWAY AT THE OWNER'S CONFIGURED TO PROTECT AGAINST CONTACT. THERE SHALL BE NO SHARP OR
<br /> CROSSINGS SHALL BE WHOLLY CONTAINED WITHIN THE MARKINGS, EXCLUDING EXPENSE. TOWED VEHICLES MAY BE RECLAIMED AT: ABRASIVE SURFACES UNDER LAVATORIES AND SINKS.
<br /> ANY FLARED SIDES. OR BY TELEPHONING "
<br /> 11B-606.6 ADJACENT SIDE WALL OR PARTITION. LAVATORIES, WHEN LOCATED
<br /> 11B-406.5.2 WIDTH. THE CLEAR WIDTH OF CURB RAMP RUNS (EXCLUDING ANY BLANK SPACES SHALL BE FILLED IN WITH APPROPRIATE INFORMATION AS A ADJACENT TO A SIDE WALL OR PARTITION, SHALL BEA MINIMUM OF 18 INCHES
<br /> FLARED SIDES), BLENDED TRANSITIONS, AND TURNING SPACES SHALL BE 48 PERMANENT PART OF THE SIGN. (457 MM) TO THE CENTERLINE OF THE FIXTURE.
<br /> INCHES (1219 MM) MINIMUM.
<br /> 11 B-606.7 SINK DEPTH. SINKS SHALL BE 6%2 INCHES(165 MM) DEEP MAXIMUM. ©2011 STARBUCKS COFFEE
<br /> 11B-406.5.3 LANDINGS. LANDINGS SHALL BE PROVIDED AT THE TOPS OF CURB TOILET ROOMS
<br /> QnRADANIV
<br /> RAMPS AND BLENDED TRANSITIONS. THE LANDING CLEAR LENGTH SHALL BE 48 11B-603 TOILET AND BATHING ROOMS SIGNS STARBUCKS COFFEE
<br /> INCHES (1219 MM) MINIMUM. THE LANDING CLEAR WIDTH SHALL BE AT LEAST AS
<br /> WIDE AS THE CURB RAMP, EXCLUDING ANY FLARED SIDES, OR THE BLENDED 11B-603.2 CLEARANCES. CLEARANCES SHALL COMPLY WITH SECTION 11B-603.2. 11B-703 SIGNS COMPANY
<br /> TRANSITION LEADING TO THE LANDING. THE SLOPE OF THE LANDING IN ALL
<br /> DIRECTIONS SHALL BE 1:48 MAXIMUM. 11B-603.2.1 TURNING SPACE. TURNING SPACE COMPLYING WITH SECTION 11B-703.2 RAISED CHARACTERS. RAISED CHARACTERS SHALL COMPLY WITH 2401 UTAH AVENUE SOUTH
<br /> 11B-304 SHALL BE PROVIDED WITHIN THE ROOM. SECTION IIB-703.2 AND SHALL BE DUPLICATED IN BRAILLE COMPLYING WITH SEATTLE, WASHINGTON 98134
<br /> 11B-406.5.11 GROOVED BORDER. CURB RAMPS SHALL HAVE A GROOVED BORDER SECTION 11B-703.3. RAISED CHARACTERS SHALL BE INSTALLED IN ACCORDANCE (206) 318-1575
<br /> 12 INCHES (305 MM) WIDE ALONG THE TOP OF THE CURB RAMP AT THE LEVEL 11B-603.2.2 OVERLAP. REQUIRED CLEAR FLOOR SPACES, CLEARANCE AT WITH SECTION 11B-703.4.
<br /> SURFACE OF THE TOP LANDING AND AT THE OUTSIDE EDGES OF THE FLARED FIXTURES, AND TURNING SPACE SHALL BE PERMITTED TO OVERLAP. THESE DRAWINGS AND SPECIFICATIONS ARE
<br /> SIDES. THE GROOVED BORDER SHALL CONSIST OF A SERIES OF GROOVES 1/4 INCH 11B-703.2.1 DEPTH. RAISED CHARACTERS SHALL BE 1/32 INCH (0.8 MM) MINIMUM CONFIDENTIAL AND SHALL REMAIN THE SOLE
<br /> (6.4 MM) WIDE BY 1/4 INCH (6.4 MM) DEEP, AT 3/a INCH (19 MM) ON CENTER. 11B-603.2.3 DOOR SWING. DOORS SHALL NOT SWING INTO THE CLEAR FLOOR ABOVE THEIR BACKGROUND. PROPERTY OF STARBUCKS CORPORATION,WHICH IS
<br /> SPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE. OTHER THAN THE DOOR THE OWNER OF THE COPYRIGHT IN THIS WORK.
<br /> 11B-406.5.12 DETECTABLE WARNINGS. CURB RAMPS AND BLENDED TRANSITIONS TO THE ACCESSIBLE WATER CLOSET COMPARTMENT, A DOOR, IN ANY 11B-703.2.2 CASE. CHARACTERS SHALL BE UPPERCASE. THEY SHALL NOT BE REPRODUCED (IN WHOLE OR IN
<br /> SHALL HAVE DETECTABLE WARNINGS COMPLYING WITH SECTION 11B-705. POSITION, MAY ENCROACH INTO THE TURNING SPACE BY 12 INCHES (305 MM) PART), SHARED WITH THIRD PARTIES OR USED IN AN
<br /> MAXIMUM. 11B-703.2.3 STYLE. CHARACTERS SHALL BE SANS SERIF. CHARACTERS SHALL MANNER ON OTHER PROJECTS OR EXTENSIONS TO
<br /> NOT BE ITALIC, OBLIQUE, SCRIPT, HIGHLY DECORATIVE, OR OF OTHER UNUSUAL THIS PROJECT WITHOUT THE PRIOR WRITTEN
<br /> PARKING SPACES 11B-603.3 MIRRORS. MIRRORS LOCATED ABOVE LAVATORIES OR FORMS. CONSENT OF STARBUCKS CORPORATION. THESE
<br /> DRAWINGS AND SPECIFICATIONS ARE INTENDED TO
<br /> 11B-502 PARKING SPACES COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE EXPRESS DESIGN INTENT FOR A PROTOTYPICAL
<br /> > REFLECTING SURFACE 40 INCHES (1016 MM) MAXIMUM ABOVE THE FINISH 11B-703.2.4 CHARACTER PROPORTIONS. CHARACTERS SHALL BE SELECTED STARBUCKS STORE (WHICH IS SUBJECT TO CHANGE
<br /> 11B-502.1 GENERAL. CAR AND VAN PARKING SPACES SHALL COMPLY WITH FLOOR OR GROUND. MIRRORS NOT LOCATED ABOVE LAVATORIES OR FROM FONTS WHERE THE WIDTH OF THE UPPERCASE LETTER "O" IS 60 PERCENT AT ANYTIME) AND DO NOT REFLECT ACTUAL SITE
<br /> SECTION I IB-502. WHERE PARKING SPACES ARE MARKED WITH LINES, WIDTH COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE MINIMUM AND 110 PERCENT MAXIMUM OF THE HEIGHT OF THE UPPERCASE CONDITIONS. NEITHER PARTY SHALL HAVE ANY
<br /> U MEASUREMENTS OF PARKING SPACES AND ACCESS AISLES SHALL BE MADE REFLECTING SURFACE 35 INCHES (889 MM) MAXIMUM ABOVE THE FINISH FLOOR LETTER "I". OBLIGATION NOR LIABILITY TO THE OTHER (EXCEPT
<br /> �I FROM THE CENTERLINE OF THE MARKINGS. OR GROUND. STATED ABOVE) UNTIL A WRITTEN AGREEMENT IS
<br /> 11B-703.2.5 CHARACTER HEIGHT. CHARACTER HEIGHT MEASURED VERTICALLY FULLY EXECUTED BY BOTH PARTIES.
<br /> N 11B-502.2 VEHICLE SPACES. CAR AND VAN PARKING SPACES SHALL BE 216 INCHES 11B-603.5 ACCESSORIES. WHERE TOWEL OR SANITARY NAPKIN DISPENSERS, FROM THE BASELINE OF THE CHARACTER SHALL BE 5/8 INCH (15.9 MM) MINIMUM
<br /> p (5486 MM) LONG MINIMUM. CAR PARKING SPACES SHALL BE 108 INCHES(2743 MM) WASTE RECEPTACLES, OR OTHER ACCESSORIES ARE PROVIDED IN TOILET AND 2 INCHES (51 MM) MAXIMUM BASED ON THE HEIGHT OF THE UPPERCASE
<br /> >- WIDE MINIMUM AND VAN PARKING SPACES SHALL BE 144 INCHES(3658 MM)WIDE FACILITIES, AT LEAST ONE OF EACH TYPE SHALL BE LOCATED ON AN LETTER "I". ARCHITECT OF RECORD
<br /> o6 MINIMUM, SHALL BE MARKED TO DEFINE THE WIDTH, AND SHALL HAVE AN ACCESSIBLE ROUTE. ALL OPERABLE PARTS, INCLUDING COIN SLOTS, SHALL BE 11B-703.2.6 STROKE THICKNESS. STROKE THICKNESS OF THE UPPERCASE o
<br /> ADJACENT ACCESS AISLE COMPLYING WITH SECTION 118 502.3. 40 INCHES (1016 MM) MAXIMUM ABOVE THE FINISH FLOOR. LETTER "I" SHALL BE 15 PERCENT MAXIMUM OF THE HEIGHT OF THE CHARACTER. �n cz >
<br /> = w a
<br /> > o
<br /> 1 11B-703.2.7 CHARACTER SPACING. CHARACTER SPACING SHALL BE MEASURED
<br /> .3 ACCESS AISLE. ACCESS AISLES SERVING PARKING SPACES SHALL WATER CLOSETS BETWEEN THE TWO CLOSEST POINTS OF ADJACENT RAISED CHARACTERS � U
<br /> �I COMPLY WITH SECTION 118-502.3. ACCESS AISLES SHALL ADJOIN AN ACCESSIBLE „
<br /> C:) WITHIN A MESSAGE, EXCLUDING WORD SPACES. WHERE CHARACTERS HAVE
<br /> ROUTE. TWO PARKING SPACES SHALL BE PERMITTED TO SHARE A COMMON 11B-604 WATER CLOSETS
<br /> 00 ACCESS AISLE. RECTANGULAR CROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISED
<br /> T__ CHARACTERS SHALL BE 1/8 INCH (3.2 MM) MINIMUM AND 4 TIMES THE RAISED mcg a r c h i t e c u r
<br /> T__
<br /> 116-502.3.2 LENGTH. ACCESS AISLES SHALL EXTEND THE FULL REQUIRED LENGTH 11B-604.2 LOCATION. THE WATER CLOSET SHALL BE POSITIONED WITH A WALL CHARACTER STROKE WIDTH MAXIMUM. WHERE CHARACTERS HAVE OTHER
<br /> 0x0 OF THE PARKING SPACES THEY SERVE. OR PARTITION TO THE REAR AND TO ONE SIDE. THE CENTERLINE OF THE WATER CROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISED CHARACTERS SHALL 111 Pacifica, Suite 280, Irving, CA 92618
<br /> CLOSET SHALL BE 17 INCHES(432 MM) MINIMUM TO 18 INCHES (457MM) BE 1/16 INCH (1.6 MM) MINIMUM AND 4 TIMES THE RAISED CHARACTER STROKE P:949.553.1117 F:949.474.7056
<br /> �I MAXIMUM FROM THE SIDE WALL OR PARTITION, EXCEPT THAT THE WATER WIDTH MAXIMUM AT THE BASE OF THE CROSS SECTIONS, AND 1/8 INCH (3.2 MM
<br /> M 1ORDE . LI MARKING. ACCESS AISLES SHALL BE MARKED WITH A BLUE PAINTED CLOSET SHALL BE 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) MINIMUM AND 4 TIMES THE RAISED CHARACTER STROKE WIDTH MAXIMUM AT THE
<br /> BORDERLINE AROUND THEIR PERIMETER. THE AREA WITHIN THE BLUE ARCHITECT STAMP
<br /> CV MAXIMUM FROM THE SIDE WALL OR PARTITION IN THE AMBULATORY ACCESSIBLE TOP OF THE CROSS SECTIONS. CHARACTERS SHALL BE SEPARATED FROM
<br /> rn BORDERLINES SHALL BE MARKED WITH HATCHED LINES A MAXIMUM OF 36 INCHES TOILET COMPARTMENT SPECIFIED IN SECTION IIB-604SLE .8.2. WATER CLOSETS RAISED BORDERS AND DECORATIVE ELEMENTS 3/8 INCH 9.5 MM MINIMUM. 5E� ARC
<br /> SURFACE, PREFERABLY BLUN CENTER IN A OE OR WHITE.LOR THE HTE WORING IDS NO PARKING"TH THAT OF THE BE SHALL BE ARRANGED FOR A LEFT-HAND OR RIGHT-HAND APPROACH. ( ) wrly�����
<br /> PAINTED ON THE SURFACE WITHIN EACH ACCESS AISLE IN WHITE LETTERS A 116-703.2.8 LINE SPACING. SPACING BETWEEN THE BASELINES OF SEPARATE
<br /> ILL
<br /> MINIMUM OF 12 INCHES (305 MM) IN HEIGHT AND LOCATED TO BE VISIBLE FROM 11B-604.3 CLEARANCE. CLEARANCES AROUND WATER CLOSETS AND IN TOILET LINES OF RAISED CHARACTERS WITHIN A MESSAGE SHALL BE 135 PERCENT s
<br /> THE ADJACENT VEHICULAR WAY. ACCESS AISLE MARKINGS MAY EXTEND BEYOND COMPARTMENTS SHALL COMPLY WITH SECTION 11B-604.3. MINIMUM AND 170 PERCENT MAXIMUM OF THE RAISED CHARACTER HEIGHT.
<br /> THE MINIMUM REQUIRED LENGTH. 11B-604.3.1 SIZE. CLEARANCE AROUND A WATER CLOSET SHALL BE 60 INCHESP 2019
<br /> 116-703.4 INSTALLATION HEIGHT AND LOCATION. SIGNS WITH TACTILE
<br /> T__
<br /> 116-502.3.4 LOCATION. ACCESS AISLES SHALL NOT OVERLAP THE VEHICULAR (1524 MM) MINIMUM MEASURED PERPENDICULAR FROM THE SIDE WALL AND 56 CHARACTERS SHALL COMPLY WITH SECTION 11B-703.4. UM ` Qa��
<br /> INCHES (1422 MM) MINIMUM MEASURED PERPENDICULAR FROM THE REAR WALL. OF�AL!�-
<br /> U WAY. ACCESS AISLES SHALL BE PERMITTED TO BE PLACED ON EITHER SIDE OF A MINIMUM 60 INCHES(1524 MM) WIDE AND 48 INCHES(1219 MM) DEEP 11B-703.4.1 HEIGHT ABOVE FINISH FLOOR OR GROUND. TACTILE CHARACTERS
<br /> c� THE PARKING SPACE EXCEPT FOR VAN PARKING SPACES WHICH SHALL HAVE MANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET.
<br /> ACCESS AISLES LOCATED ON THE PASSENGER SIDE OF THE PARKING SPACES. ON SIGNS SHALL BE LOCATED 48 INCHES (1219 MM) MINIMUM ABOVE THE FINISH
<br /> U FLOOR OR GROUND SURFACE, MEASURED FROM THE BASELINE OF THE LOWEST
<br /> 116-502.4 FLOOR OR GROUND SURFACES. PARKING SPACES AND ACCESS AISLES 11B-604.3.2 OVERLAP.THE REQUIRED CLEARANCE AROUND THE WATER CLOSET BRAILLE CELLSAND 60 INCHES (1524 MM) MAXIMUM ABOVE THE FINISH FLOOR OR
<br /> Q
<br /> < SERVING THEM SHALL COMPLY WITH SECTION 11 G SP ACCESS AISLES SHALL BE SHALL BE PERMITTED TO OVERLAP THE WATER CLOSET, ASSOCIATED GRAB GROUND SURFACE, MEASURED FROM THE BASELINE OF THE HIGHEST LINE OF
<br /> C:) AT THE SAME LEVEL AS THE PARKING SPACES THEY SERVE. CHANGES IN LEVEL BARS, DISPENSERS, SANITARY NAPKIN DISPOSAL UNITS, COAT HOOKS, SHELVES, RAISED CHARACTERS.
<br /> i ARE NOT PERMITTED. ACCESSIBLE ROUTES, CLEAR FLOOR SPACE AND CLEARANCES REQUIRED AT
<br /> OTHER FIXTURES, AND THE TURNING SPACE. NO OTHER FIXTURES OR 11B-703.4.2 LOCATION.WHERE A TACTILE SIGN IS PROVIDED AT A DOOR, THE
<br /> 75; 116-502.5 VERTICAL CLEARANCE. PARKING SPACES, ACCESS AISLES AND
<br /> OBSTRUCTIONS SHALL BE LOCATED WITHIN THE REQUIRED WATER CLOSET SIGN SHALL BE LOCATED ALONGSIDE THE DOOR AT THE LATCH SIDE. WHERE A VEHICULAR ROUTES SERVING THEM SHALL PROVIDE A VERTICAL CLEARANCE OF CLEARANCE. TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGN W
<br /> Q 98 INCHES (2489 MM) MINIMUM. SHALL BE LOCATED ON THE INACTIVE LEAF. WHERE A TACTILE SIGN IS PROVIDED
<br /> UI 11B-604.4 SEATS. THE SEAT HEIGHT OF A WATER CLOSET ABOVE THE FINISH AT DOUBLE DOORS WITH TWO ACTIVE LEAFS, THE SIGN SHALL BE LOCATED TO
<br /> 116-502.6 IDENTIFICATION. PARKING SPACE IDENTIFICATION SIGNS SHALL INCLUDE FLOOR SHALL BE 17 INCHES (432 MM) MINIMUM AND 19 INCHES (483 MM) THE RIGHT OF THE RIGHT HAND DOOR. WHERE THERE IS NO WALL SPACE AT THE
<br /> THE INTERNATIONAL SYMBOL OF ACCESSIBILITY COMPLYING WITH SECTION MAXIMUM MEASURED TO THE TOP OF THE SEAT. SEATS SHALL NOT BE SPRUNG LATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT SIDE OF DOUBLE DOORS,
<br /> I IB-703.7.2.1. SIGNS IDENTIFYING VAN PARKING SPACES SHALL CONTAIN TO RETURN TO A LIFTED POSITION. SEATS SHALL BE 21NCHES(51 MM) HIGH SIGNS SHALL BE LOCATED ON THE NEAREST ADJACENT WALL. SIGNS W Cco
<br /> ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGN WITHTHE DESIGNATION "VAN MAXIMUM. CONTAINING TACTILE CHARACTERS SHALL BE LOCATED SO THAT A CLEAR
<br /> ACCESSIBLE." SIGNS SHALL BE 60 INCHES 1524 MM MINIMUM ABOVE THE FINISH FLOOR SPACE OF 18 INCHES (457MM) MINIMUM BY 18 INCHES (457MM) MINIMUM,
<br /> �I ( ) 11B-604.5 GRAB BARS. GRAB BARS FOR WATER CLOSETS SHALL COMPLY WITH CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OF 0 L0(D FLOOR OR GROUND SURFACE MEASURED TO THE BOTTOM OF THE SIGN. O7
<br /> �
<br /> SECTION 11B-609. GRAB BARS SHALL BE PROVIDED ON THE SIDE WALL CLOSEST ANY DOOR SWING BETWEEN THE CLOSED POSITION AND 45 DEGREE OPEN O
<br /> E 11B-502.6.1 FINISH AND SIZE. PARKING IDENTIFICATION SIGNS SHALL BE TO THE WATER CLOSET AND ON THE REAR WALL. WHERE SEPARATE GRAB BARS POSITION. WHERE PERMANENT IDENTIFICATION SIGNAGE IS PROVIDED FOR (jj Q
<br /> cn ARE REQUIRED ON ADJACENT WALLS ATA COMMON MOUNTING HEIGHT, AN L- ROOMS AND SPACES THEY SHALL BE LOCATED ON THE APPROACH SIDE OF THE
<br /> p REFLECTORIZED WITH A MINIMUM AREA OF 70 SQUARE INCHES (45161 MM2). SHAPED GRAB BAR MEETING THE DIMENSIONAL REQUIREMENTS OF SECTIONSLU O U
<br /> DOOR AS ONE ENTERS THE ROOM OR SPACE. SIGNS THAT IDENTIFY EXITS SHALL
<br /> } 11B-604.5.1 AND 11B-604.5.2 SHALL BE PERMITTED. BE LOCATED ON THE APPROACH SIDE OF THE DOOR AS ONE EXITS THE ROOM LLJ Cc
<br /> Q
<br /> o06116-502.6.2 MINIMUM FINE. ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGN o Z Q
<br /> • FINE $250."
<br /> C BELOW THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL STATE "MINIMUM OR SPACE. Z W
<br /> p 11B-604.5.1 SIDE WALL. THE SIDE WALL GRAB BAR SHALL BE 42 INCHES (1067MM)
<br /> z Q
<br /> LONG MINIMUM, LOCATED 12 INCHES (305 MM) MAXIMUM FROM THE REAR WALL O
<br /> AND EXTENDING 54 INCHES (1372 MM) MINIMUM FROM THE REAR WALL WITH THE U U
<br /> �I 11B-502.6.3 LOCATION. A PARKING SPACE IDENTIFICATION SIGN SHALL BE VISIBLE W - LU
<br /> C:) FRONT END POSITIONED 24 INCHES(610 MM) MINIMUM IN FRONT OF THE WATER
<br /> co FROM EACH PARKING SPACE. SIGNS SHALL BE PERMANENTLY POSTED EITHER CLOSET.
<br /> 00 IMMEDIATELY ADJACENT TO THE PARKING SPACE OR WITHIN THE PROJECTED 0 0 N C
<br /> T__ PARKING SPACE WIDTH AT THE HEAD END OF THE PARKING SPACE. SIGNS MAY 11B-604.5.2 REAR WALL. THE REAR WALL GRAB BAR SHALL BE 36 INCHES (914 T C
<br /> ALSO BE PERMANENTLY POSTED ON A WALL AT THE INTERIOR END OF THE MM) LONG MINIMUM AND EXTEND FROM THE CENTERLINE OF THE WATER
<br /> co PARKING SPACE. CLOSET 12 INCHES (305 MM) MINIMUM ON ONE SIDE AND 24 INCHES (610 MM)
<br /> I MINIMUM ON THE OTHER SIDE. STORE #: 11830
<br /> CV 11B-502.6.4 MARKING. EACH ACCESSIBLE CAR AND VAN SPACE SHALL HAVE
<br /> co SURFACE IDENTIFICATION COMPLYING WITH EITHER SECTION 11B-502.6.4.1 OR PROJECT #: 37913-049
<br /> N 11B-604.6 FLUSH CONTROLS. FLUSH CONTROLS SHALL BE HAND OPERATED OR
<br /> 11 B 502.6.4.2. CASEWORK CONCEPT: CORE
<br /> rn AUTOMATIC. HAND OPERATED FLUSH CONTROLS SHALL COMPLY WITH SECTION
<br /> 116-502.6.4.1 THE PARKING SPACE SHALL BE MARKED WITH AN INTERNATIONAL 116-309 EXCEPT THEYSHALL BE LOCATED 44 INCHES(1118 MM) MAXIMUM ABOVE ISSUE DATE:
<br /> L
<br /> (Yj SYMBOL OF ACCESSIBILITY COMPLYING WITH SECTION 11 B 703.7.2.1 IN WHITE L THE FLOOR. FLUSH CONTROLS SHALL BE LOCATED ON THE OPEN SIDE OF THE PROGRAM MANAGER: M.DREBIKA
<br /> Z) A BLUE BACKGROUND A MINIMUM 36 INCHES WIDE BY 36 INCHES HIGH (914 MM X WATER CLOSET EXCEPT IN AMBULATORY ACCESSIBLE COMPARTMENTS STORE DESIGNER: T.MARINIC
<br /> CO 914 MM). THE CENTERLINE OF THE INTERNATIONAL SYMBOL OF ACCESSIBILITY COMPLYING WITH SECTION 118-604.8.2. LEEDOAP: N/A
<br /> Cc SHALL BE A MAXIMUM OF 6 INCHES (152 MM) FROM THE CENTERLINE OF THE
<br /> Q 11B-604.7 DISPENSERS.TOILET PAPER DISPENSERS SHALL COMPLY WITH CHECKED BY:
<br /> I- PARKING SPACE, ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACE SECTION 11B-309.4 AND SHALL BE 7 INCHES (178 MM) MINIMUM AND 9 INCHES (229
<br /> � AND ITS LOWER CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THE MCG PROJECT#: 19232
<br /> o PARKING SPACE LENGTH. MM) MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO THE
<br /> _ CENTERLINE OF THE DISPENSER. THE OUTLET OF THE DISPENSER SHALL BE MCG PROJ. MANAGER: C.LEE
<br /> 116-502.6.4.2THE PARKING SPACE SHALL BE OUTLINED OR PAINTED BLUE AND BELOW THE GRAB BAR, 19 INCHES(483 MM) MINIMUM ABOVE THE FINISH FLOOR MCG PROJ. SPECIALIST: SPARK
<br /> v AND SHALL NOT BE LOCATED BEHIND GRAB BARS. DISPENSERS SHALL NOT BE
<br /> a� SHALL BE MARKED WITH AN INTERNATIONAL SYMBOL OF ACCESSIBILITY OF A TYPE THAT CONTROLS DELIVERY OR THAT DOES NOT ALLOW CONTINUOUS
<br /> o COMPLYING WITH SECTION 11B-703.7.2.1 A MINIMUM 36 INCHES WIDE BY 36 INCHES PAPER FLOW. Revision Schedule
<br /> CL HIGH (914 MM X 914 MM) IN WHITE OR A SUITABLE CONTRASTING COLOR. THE
<br /> rn CENTERLINE OF THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL BE A Rev Date By Description
<br /> T__ MAXIMUM OF 6 INCHES (152 MM) FROM THE CENTERLINE OF THE PARKING SPACE, LAVATORIES
<br /> N ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACE AND ITS LOWER
<br /> CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THE PARKING SPACE. 11B-606 LAVATORIES AND SINKS
<br /> 11B-502.8 ADDITIONAL SIGNAGE. AN ADDITIONAL SIGN SHALL BE POSTED EITHER; 11B-606.2 CLEAR FLOOR SPACE. A CLEAR FLOOR SPACE COMPLYING WITH
<br /> 1) IN A CONSPICUOUS PLACE AT EACH ENTRANCE TO AN OFF-STREET PARKING SECTION I IB-305, POSITIONED FOR A FORWARD APPROACH, AND KNEE AND
<br /> Q FACILITY OR 2) IMMEDIATELY ADJACENT TO ON-SITE ACCESSIBLE PARKING AND TOE CLEARANCE COMPLYING WITH SECTION 116-306 SHALL BE PROVIDED. SHEET TITLE:
<br /> U-) VISIBLE FROM EACH PARKING SPACE.
<br /> 0 11B-606.3 HEIGHT. LAVATORIES AND SINKS SHALL BE INSTALLED WITH THE ACCESSIBILITY NOTES
<br /> U-) 11B-502.8.1 SIZE. THE ADDITIONAL SIGN SHALL NOT BE LESS THAN 17 INCHES (432 FRONT OF THE HIGHER OF THE RIM OR COUNTER SURFACE 34 INCHES (864
<br /> p MM) WIDE BY 22 INCHES (559 MM) HIGH. MM) MAXIMUM ABOVE THE FINISH FLOOR OR GROUND.
<br /> T__ 11B-606.4 FAUCETS. CONTROLS FOR FAUCETS SHALL COMPLY WITH SECTION
<br /> 0 11B-502.8.2 LETTERING. THE ADDITIONAL SIGN SHALL CLEARLY STATE IN LETTERS I IB-309. HAND-OPERATED METERING FAUCETS SHALL REMAIN OPEN FOR 10 SCALE:AS SHOWN
<br /> N WITH A MINIMUM HEIGHT OF 1 INCH (25 MM) THE FOLLOWING: SECONDS MINIMUM.
<br /> SHEET NUMBER:
<br /> co
<br /> r G005
<br /> T
<br />
|