Laserfiche WebLink
FEmirw <br /> TECHNICAL BULLETIN <br /> Franklin Fueling Systems April 30, 2007 <br /> Pump Designation Listing <br /> 4" Pumps - A typical FE Petro 4" pump model number will have up to seven components defining the pump being <br /> supplied. The format for model designation is as follows. See back of this document for examples of model <br /> designation. <br /> XXX (XXX) YYYYY ZZZ V -WWW - QQ <br /> 1 2 3 4 5 6 7 <br /> 1 = Basic Model Designation <br /> IST Intelligent Submersible Turbine(VS2 is implied if not suffixed with VS4. AG is always implied with IST) <br /> STP Submerged Turbine Pump <br /> 2 = Approval Option Designations <br /> ATX European <br /> RT Russian <br /> SAA Australia <br /> 3 = Basic Mechanical Option Designations <br /> AG" Suitable for blend concentrations of: 0%- 15%ethanol or methanol 20% MTBE with 80%gasoline <br /> (Standard on IST)20% ETBE with 80%gasoline 17% TAME with 83%gasoline <br /> EXT Extractable portion—less motor and hardware(STPs and ISTs) <br /> F Floating suction adapter <br /> H High pressure(2 and 1-1/2 HP models only) <br /> K Intake Filter Screen (IFS) assembled onto turbine in manufacturing (4" models only) <br /> L Foot valve diffuser(4" PMAs only) <br /> M MagShellT", expanded PMA shell for 2 HP (both fixed and variable speed) and 4 HP models only. <br /> R— Check Valve set to reset about 22 psi;for use with Veeder Root Pressure Electronic Line Leak Detectors <br /> S Syphon Check Valve included, but not attached. <br /> V Vapor recovery discharge port(4" models only) <br /> W** Check Valve set to reset about 13 psi-for use with Red Jacket Electronic Line Leak Detectors. <br /> Standard 4"models are suitable for same blend concentrations of ETBE, MTBE, and TAME as AG,but,with gasoline, <br /> only concentrations of 0%-15%ethanol or methanol are suitable. <br /> If not specified, a"STD" check valve(which holds at 35-45 psi) is implied. <br /> 4 = Motor Horsepower Rating <br /> 33 1/3 HP fixed speed <br /> 75 3/4 HP fixed speed <br /> 150 1 1/2 HP fixed speed <br /> 200 2 HP fixed speed <br /> VS2 2 HP variable speed <br /> VS4 4 HP variable speed <br /> Note: IST(Intelligent Submersible Turbine) pumps use a Variable Speed 2 HP when no suffix is present and a <br /> Variable Speed 4 HP when the VS4 suffix appears. <br /> 5 = Voltage, Frequency, and Phase Ratings <br /> A 208-230 V, 60 Hz, single phase (assumed if no rating is specified) <br /> B 200-250 V, 50 Hz, single phase <br /> C 380-415 V, 50 Hz, three phase <br /> E 200 V, 60 Hz, three phase <br /> F 200 V, 50 Hz, three phase <br /> Note: Variable Speed motors have a 190V, 70 Hz, three phase rating. The required power is produced from <br /> either an IST-VFC or a MagVFC controller. <br /> 6 = Model Length <br /> A three digit number that represents the pump length in inches. IST uses 1, 2, or 3 to denote length. Variable <br /> length STPs and ISTVS4s use VI-1, VI-2, or VI-3 to denote length. See price list for actual variable model <br /> length ranges. <br /> 7 = Riser Length <br /> Numeric characters that indicate length of riser pipe in inches. See price list for actual stocked riser lengths. <br /> Page 1 of 2 <br />