INSTALL_2011 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed Red Thread® II A Piping System RED THREAD IIA PIPING RED THREAD IIA PFimary Piping RED THREAD IIA Secondary Containment Piping Nom.Pipe Pipe Nom.Pipe Pipe Size Part Length Size Part Length (InJ.. .) Number (ft.) (In.lmm) Number (ft) 2 50 011020-069-1 15 3 80 011030-069-4 15 2 50 011020-069-2 22-25 3 80 011030-069-5 22-25 2 50 011020-069-3 26-30 3 80 011030-069-6 26-30 3 80 011030-069-1 15 4 100 011040-077-5 15 3 80 011030-069-2 22-25 4 100 011040-069-5 22-25 3 80 011030-069-3 26-30 4 100 011040-077-6 26-30 4 100 011040-071-1 15 6 150 011060-120-5 15 4 100 011040-069-2 22-25 6 150 011060-120-4 22-25 4 100 011040-071-3 26-30 6 011060-120-6 26-30 DIMENSIONAL DATA Nominal Nominal Mill Pipe Nominal Nominal Wall Nominal Pressure/ Test External Pressure Size I.D. O.D. Thickness Weight Temperature Pressure Max.Rating(psig/MPa) (InJ ") (InJ;°n) (in./rnrn) (InJm,) (lbsJftA ) Max.Rating (pelylMPa) 75'F/24'C 150'F/66'C 2 2.235 2.375 .070 0.5 250 psig @ 150'F 375 85 80 61 1.78 0.74 1.72 MPa @ 66°C 2.59 .57 .55 3 3.360 3.500 .070 0.7 175 psig Q 15WF 300 36 34 85 90 2.54 1.04 1.21 MPa @ 66°C 2.07 .25 .23 4 4.390 4.560 .085 1.2 125 psfg C 150-F 265 34 30 100 111 116 2.16 1.79 0.86 MPa @ 66'C 1.83 .23 .21 6 6.408 6.678 .135 2.4 NA 285 22 20 150 163 170 3.43 351 NA 1.83 .15 .14 TYPICAL PHYSICAL PROPERTIES" PROPERTY RED THREAD'IIA PIDe Bending Radius,Minimum Nominal psi @ 75'F MPa @ 24 psi @ 150'F NIPa @ 66°C Pipe Size 2" 3" 4" 6" Axial Tensile(ASTM D2105) inches Ultimate Stress 10,300 71.0 8,200 56 5 Design Stress 2,575 17.8 2,050 14.1 Ft. 75 110 140 204 Modulus of Elasticity 1.82 x 10° 12548 1.42 x 10' 9791 Axial Compression(ASTM D695) 33,300 230.0 25,600 177.0 13.5 427 62.2 Ultimate Stress 8,300 572 6,400 44.1 Design Stress 1.26 x 10' 8687 .89 x 10' 6136 Modulus of Elasticity (1) All values except pressure-temperature Beam Bending(SFPTM) maximum rating are nominal values.Tolerances or Ultimate Stress 23,000 159.0 19,203 132.0 maximum/minimum limits can be obtained from Smith Design StressM 2,900 20.0 2,400 16.5 Fibercast Modulus of Elasticity 2.18 x 10' 15031 1.70 x 10' 11721 (2) Al sizes can accept full vacuum pressures at (Long Tenn per ASTM D2925) maximum temperature ratings. (3) Ultimate and allowable design stresses are Hydrostatic Burst(ASTM D1599) based on minimum reinforced wall thickness.Pipe is Ultimate Hoop 000 39,200 271 manufactured in compliance with ASTM D29%. Tensile Stress (4) Design bending stress is 1/8 of ultimate to account for combined stress(i.e.bending and Hydrostatic Design(ASTM 02992) 2'-3" 2'8 3" 213' 213" pressure). Procedure A 9,41001 64.91 7,400(0 51'°' (5) Design stress is based on long term cyclic fatigue Cyclic 150 x 10' 4'-6- 4"•6" V.6' 4"-6" data using ASTM 02992 test method.However,all Cycles 13,040"' 89.9` 10,450 72 1 testing is not complete at time of printing. (6) For RED THREAD IIA pipe the hydrostatic Coefficient of Linear 088 x 104 nAnJ'F cyclic design stress was determined at 150'and Thermal Expansion(SFPTM) 1.58 x 10'mm/mm/'C 2007,per ASTM D2992 Procedure A.Based on this data,the extrapolated value at 75"F is 13,030 psi. Specific Gravity 1.8 (7) For RED THREAD IIA pipe the hydrostatic cyclic Flow Factor design stress was determined at 75'and 200'F,per Hazen-Williams Coefficient 150 ASTM D2992 Procedure A.Based on this data,the extrapolated value at 150'F is 7,400 psi. 4