INSTALL_2011 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed Red Thread®II A Piping System GENERAL SPECIFICATIONS Primary Piping Secondary Containment Piping SCOPE SCOPE PIPE—Pipe shall be manufactured by Smith Fibercast by a PIPE—Pipe shall be manufactured by Smith Fibercast by a filament winding process using a thermosetting epoxy resin filament winding process using a thermosetting epoxy resin to impregnate strands of continuous glass filaments which to impregnate strands of continuous glass filaments which are wound around a mandrel at a prescribed helix angle and are wound around a mandrel at a prescribed helix angle and under controlled tension. All pipe will be supplied with under controlled tension. matching tapered T.A.B."m (Threaded and Bonded)coupling and spigot ends or T.A.B.spigot x spigot ends. CONSTRUCTION CONSTRUCTION 3"-6"PIPE—RED THREAD IIA pipe shall have continuous glass fibers filament wound at a 54'wind angle in a matrix 2"4"PIPE—RED THREAD IIA pipe shall have continuous of epoxy resin. Pipe shall be in compliance with ASTM glass fibers filament wound at a 54'wind angle in a matrix D2310 and classified by its designation code. Pipe shall of epoxy resin. Pipe shall be in compliance with ASTM meet all performance requirements and mechanical D2310 and classified by its designation code. Pipe shall properties,and shall be classified with the following meet all dimensional and performance requirements, designation codes: mechanical properties,and shall be classified with the size Designation Cods at 73.4'F following designation codes: 3^ RTRP-11AF size Designation Code at 73.4'F 4"-6" RTRP-11 AH 2'-3" RTRP-11AF 4' RTRP-11AH ITEMS 3"-6"PIPE—Glass fiber reinforced filament wound pipe with ITEMS Plain end by Plain end or T.A.B.spigot by spigot ends. Pipe 2"-4"PIPE—Glass fiber reinforced filament wound pipe with to be factory prooftested at the following pressures: matching tapered T.A.B.(Threaded and Bonded)coupling 3"-300 prig(minimum) and spigot ends or T.A.B.spigot by spigot ends. Pipe to be 4"-265 psig(minimum) factory prooftested at the following pressures: 6"-265 psig(minimum) 2"-375 prig 3"-300 psig 3"-6"FITTINGS—Compression molded two-piece fittings 4"-265 psig shall be manufactured using a vinyl ester molding 2"�"FITTINGS—Com Compression molded fittings shall be compound. The molding compound shall be reinforced with P 9s a minimum of 60%chopped glass fiber. manufactured using an epoxy molding compound. The molding compound shall be reinforced with a minimum of ADHESIVES—Adhesive and curing agents shall be either i 45%chopped glass fiber. In-line fittings are filament wound. FListed 8000 or series adhesive. Consult Smith Fibercast's installation manual No.82160 for recommended ADHESIVES—Adhesive and curing agents shall be either heat curing techniques. UL Listed 8000 or 7000 series adhesive. Consult Smith Fibercast's installation manual No. 82160 for JOINING TECHNIQUES recommended heat curing techniques. 3"-6"PIPE and FITTINGS—Pipe shall be joined with either JOINING TECHNIQUES 8000 or 7000 series adhesive. Fittings shall be joined with either 7000 or 8000 series adhesives and filler. Material to 2"-4"PIPE and FITTINGS—Pipe and fittings shall be joined be installed in accordance with Smith Fibercast's installation with 8000 or 7000 series adhesive using matching tapered manual No. B2160. bellicoupling and spigot. Material to be installed in TESTING accordance with Smith Fibercast's installation manual No. B2160. 3"-6"SECONDARY CONTAINMENT PIPE SYSTEMS— Secondary containment pipe systems should be tested prior TESTING to use to assure soundness of all joints and connections. 2"-4"PRIMARY PIPE SYSTEMS—Primary pipe systems Consult Smith Fibercast's installation manual No.82160. should be tested prior to use to assure soundness of all joints and connections. Consult Smith Fibercast's installation manual No.B2160. Note:6"secondary containment pipe and Btbngs are not UL/ULC Listed. 10