COMPLIANCE INFO_2020 - Laserfiche WebLink

Home Browse Search

Eye Contact Immediately flush eyes with plenty of water,occasionally lifting the upper and lower eyelids.Check for and remove any contact lenses.Get medical attention if irritation occurs. Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing.Get medical attention if symptoms occur. Skin Contact Flush contaminated skin with plenty of water.Get medical attention if symptoms occur. Wash out mouth with water.If material has been swallowed and the exposed person is conscious,give ingestion small quantities of water to drink.Do not induce vomiting unless directed to do so by medical personnel. Get medical attention if symptoms occur. MOST IMPORTANT SYMPTOMS/EFFECTS,ACUTE AND DELAYED -POTENTIAL ACUTE HEALTH'EFFECTS Exposure to hazardous substances is not expected when handling this product for its intended use.The General information product is essentially inert with low oral and dermal toxicity.In some workplaces,operations with this product may lead to generation of dust.Exposure to dusts may have occupational health hazards. Eye Contact Dust may cause mechanical irritation to eyes. inhalation Dust may cause mechanical irritation to respiratory system. Skin Contact Dust may cause mechanical irritation to skin. Ingestion Dust may cause choking if swallowed. OVER-EXPOSURE SIGNS/SYMPTOMS Eye Contact No known significant effects or critical hazards. i Inhalation No known significant effects or critical hazards. Skin Contact No known significant effects or critical hazards. Ingestion No known significant effects or critical hazards. INDICATION OF IMMEDIATE MEDICAi:ATTENTION AND SPECIAL TREATMENT-.NEEDED,IF NECESSARY Notes to Physician Treat symptomatically.Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Specific Treatments No specific treatment. Protection of First-aiders No special protection is required. See toxicological information(Section 11) Suitable Extinguishing Media Use water,dry chemical,carbon dioxide or chemical foam. Unsuitable Extinguishing None known. Media During a fire,burning may generate carbon monoxide,carbon dioxide,carbonyl halides,gaseous hydrogen chloride,gaseous hydrogen fluoride,irritating and toxic fumes.Burning of large volumes of foam can produce dense clouds of thick,black smoke,which can make it difficult to escape from the fire area. Overheating can produce a hot,semi-liquid melt,which can produce contact blisters and release toxic Specific Hazards Arising from and/or flammable gases or vapors.Foam may tend tomelt while burning,forming a flaming,molten the Chemical product,which could spread the fire.Beware of smoldering re-ignition.After extinguishing,soak completely,tear or cut foam apart and remove burned material to a safe outdoor area.CAUTION,Foam may appear to be extinguished but may be burning or smoldering internally and/or contain molten product.Do not allow smoking in areas where foams are made or stored.Check for compliance with insurance regulations,local building codes or other legal requirements. Hazardous Thermal Under fire conditions:carbon monoxide,carbon dioxide,gaseous hydrogen chloride,gaseous hydrogen Decomposition Products fluoride,irritating and toxic fumes. Special Protective Actions far As for any fire,evacuate the area and fight the fire from a safe distance.Wear a pressure demand,self- Fire Fighters contained breathing apparatus and full protective gear.Fight fire from a protected location or a safe distance.Any water runoff should be minimized and contained. Always respect recommended processing installation procedures,maximum thickness per coat and cooling,never apply excessive thickness in one application,as it could cause spontaneous combustion of the foam hours after the foam was installed. Rigid polyurethane foam can present fire risks in some applications when exposed to ignition sources. Special Precautions Once ignited,this product can burn rapidly and produce rapid flame spread,quick flashover,toxic or flammable gases,dense smoke and intense heat,in no event should the polyurethane foam remain exposed or unprotected.Make no application of foam to interior wall and ceilings or other space enclosures without prompt and subsequent application of approved thermal barriers.No welding or flame cutting until proper surface protection has been provided. Special Protective Equipment Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus 3315 E.Division Street,Arlington,TX 76011 Heatlok HFO Pro Safety Data Sheet Phone(817)640-4900,Fax(817)633-2000 Last Revision 9-17-19 info@Demilec.com,www.Demilec.com Page 2 of 7 f