COMPLIANCE INFO_2004-2005 - Laserfiche WebLink

Home Browse Search

Secondary Containment System Installation S!l P NECTIfl 5 the outside sump wall while pressing the metal ring against the alignment ring on the inside. A. Entry and Termination at the Sump j. Do not disturb assembly until the adhesive is cured. 1. Sump EntrylTerminatfon Fitting with This includes bonding of pipe to the entry fitting and Bonded Fiberglass Alignment Rings installing the threaded outlet fitting.Clean excess ad- hesive from all bonding surfaces.See adhesive kit in- NOTE: Fiberglass ring seals can only be bonded to a flat structions for cure times. fiberglass surface.DO NOT install on round sumps. DO NOT k. The use of an industrial hot air gun may speed up the use with series piping. curing process. Do not overheat. a. Determine entry hole location and cut entry hole in I. Remove '/"plastic threaded outlet protector.Apply ad- sump wall using dimensions in Table 13. (Maximum hesive to the / fitting and screw into the /4"threaded allowable offset is 5".) outlet.Tighten to 40 in-lbs or 1'/r2 turns past hand tight. After installing the fitting,be sure the interstitial space is TABLE 13. Fitting Dimensions free from excess adhesive. Install a short hose and blow excess adhesive through the air passage. Size A B C m. Connect only flexible tubing or hoses to the 1/4"side-out- (in.) (in.) (in.) (in) let.NOTE:tubing or hoses must be rated to full vacuum. n. Bond primary pipe. 3x2 6.83 4.00 4.00 o. After primary pipe has been tested,use a concentric 4x3 6.83 4.00 5.00 reducer to bond the sump entry/termination fitting to the secondary containment piping.Do not use a clam b. Using 40-60 grit sanding surface,sand the area around shell termination fitting in place of the concentric the hole where the alignment rings will bond to the reducer. See Termination Example below. sump. Lightly sand the rings. Remove dust and wipe Refer to Bulletin No.82104 for more detailed information. with solvent(Optional). BONDED Sump Entry/Termination Fitting Body c. Place two alignment rings on sump entryttermination fitting and insert through sump wall with the rings on sump Wail the outside of the wall. Locate the 1/4"threaded outlet Bond Ring to the desired location. For a gravity drain or open 1 system,the 1/4"threaded outlet should be located at the 6 o'clock position.Leave'/4"plastic threaded outlet Protector in place until'/<"fitting installation. __--------.__.. . � Retaining Ring d. Dry fit primary pipe and rotate the two rings until the / desired angle is reached.Make alignment marks on !J the rings and the sump wall. c e. Place one ring over the sump fitting in the inside of the _ Hole Dia. sump and rotate to the desired angle. Make alignment - ----" - - - 1 mark on both the sump wall and the ring. f. Mix one 7014 or 8014 adhesive for each fitting per the instructions in the adhesive kit.Mix in filler to thicken adhesive(fiberglass alignment ring will not seal s ( $ Inside Sump properly out filler). A g. Apply adhesive generously,approximately 1/16" thick to the inside and the outside of the sump TERMINATION EXAMPLE using walls where the alignment rings are lo- i SUMP ETRY/TE IATIN FITTINGS cated.Be sure to coat cut edges of Minimized insertion _ hole. I a thin coating of _ Primary Pipe- the entry Apply 9 Make air � � C Red Thread 81a adhesive to the bonding surface of the passage is clear \\ Concentric Reducer two rings that will bond to the sump walls. o h. Line up rings with alignment marks and press to- ° ! ° gether firmly. 1. Slide the metal retaining ring over the inside section of sump fitting against the alignment rings until they are tight against sump wall.(A short section of 4"pipe may be used to drive the metal retaining ring over the ° ° containment Pipe fitting.)Be sure there Is an adhesive bead visible Red Thread iia between the rings and the sump wall.The metal `Sump Entry/Termination Fitting ring must hold the assembly in position while the �--SpigotxNPTAdapterorSpigotxSpigotNipple adhesive cures.If the assembly is not tight against Use concentric reducer to connect the sump entry/termination the sump wall,firmly press the entry fitting against rating to secondary containment pipe;DO NOT USE clam shell termination fittings with this style fitting. RED THREAD 11A Pipe & Fittings 4. 20