COMPLIANCE INFO_1986-1996 - Laserfiche WebLink

Home Browse Search

Ij 17. FILL -UP FOR TEST Stick Water Bottom A before Fill -up to % in. a Gallons Fill up. STICK BEFORE AND AFTER EACH COMPARTMENT DROP OR EACH METERED DELIVERY QUANTITY Inventory Stick Readings to % in. Q/. w Total Gallons Gallons ea. Reading ®?(p O Tank Diameter Q n Product in full tank (up to fill pipe) 18. SPECIAL CONDITIONS AND PROCEDURES TO TEST THIS TANK Hyd"tl Rr� i ® %�°F VAPOR RECOVERY SYSTEM .,1j, 11� r 1960 / �!+ See manual sections applicable. Check below and record procedure in log (26). CD ri d ! 7-O r ® v �, (p 1960 */ n Stage I F] Water in tank ❑ High water table in tank excavation F1 Une(s) being tested with LVLLT n Stage 11 N 19. TANK MEASUREMENTS FOR 1 TSTT ASSEMBLY / ut Bottom of tank to Grade* ..................... tD Add 30" for 4: L ................. H Add 24" for 3" L or air seal ....... / rr Total tubing to assemble Approximate / r r 20. EXTENSION HOSE SETTING /7' , Tank top to grade'.......'r Extend hose on suction tube 6" or more below tank top ................. /0 n n 'If Fill pipe extends above grade, use top of fill. 21. 14. Atye`eA V f#/a .3 CQj(,o N gam Ldrit- Zod ,f 9-/0 Co Is Today Warmer? [J Colder? [7 —n F Product in Tank _° F Fill -up Productions Name of Supplier, Owner or Dealer Address No. and Street(s) City -. State Date of Test 29. Reading No. Standpipe Level in Inches 15. TANK TO TEST 16. CAPACITY From Zy ^ M act 3 • f/�.Q yr Nominal Capacity- Station Chart By most accurate /'y/'� ❑ , capacity chart available v Tank Manufacturer's Chart Sa `- Identity by position Gallons Gallons Company Engineering Data �} 82.817f J ratr M Is there doubt as to True Capacity? Charts supplied with "Piro T. Lte gallons Brand and Grade See Section "DETERMINING TANK CAPACITY" Other IAN TESTER Ij 17. FILL -UP FOR TEST Stick Water Bottom A before Fill -up to % in. a Gallons Fill up. STICK BEFORE AND AFTER EACH COMPARTMENT DROP OR EACH METERED DELIVERY QUANTITY Inventory Stick Readings to % in. Q/. w Total Gallons Gallons ea. Reading ®?(p O Tank Diameter Q n Product in full tank (up to fill pipe) 18. SPECIAL CONDITIONS AND PROCEDURES TO TEST THIS TANK Hyd"tl Rr� i ® %�°F VAPOR RECOVERY SYSTEM .,1j, 11� r 1960 / �!+ See manual sections applicable. Check below and record procedure in log (26). CD ri d ! 7-O r ® v �, (p 1960 */ n Stage I F] Water in tank ❑ High water table in tank excavation F1 Une(s) being tested with LVLLT n Stage 11 N 19. TANK MEASUREMENTS FOR 1 TSTT ASSEMBLY / ut Bottom of tank to Grade* ..................... tD Add 30" for 4: L ................. H Add 24" for 3" L or air seal ....... / rr Total tubing to assemble Approximate / r r 20. EXTENSION HOSE SETTING /7' , Tank top to grade'.......'r Extend hose on suction tube 6" or more below tank top ................. /0 n n 'If Fill pipe extends above grade, use top of fill. 21. TEMPERATURE/VOLUME FACTOR (a) TO TEST THIS TANK 31. VOLUME MEASUREMENTS M RECORD TO GAL 34' TEMPERATURE COMPENSATION USE FACTOR(a) Is Today Warmer? [J Colder? [7 —n F Product in Tank _° F Fill -up Productions Truck _° F Expected Change ( + or - ) 22. Thermal -Sensor reading after circulation °F 29. Reading No. Standpipe Level in Inches 3/8 digits _ Nearest - 35. Thermal Sensor Reading 23. Digits per °F in range of expected change Temperature 1 At Nips I" record TOW End Deflection Beginning of Reading digits Volume Varome Minus Expansion (+) or Contraction (-) #33(V) -#37(T) At low Lerel compute ewe per Now (NFPAcriteria) 24. Q G7 X IF 000 �S3��® �} 82.817f J Product Recovered (+) total quantity in 'coefficient of expansion for _ volume change in this tank gallons full tank (16 or 17) involved product per °F ('0084) 25. Q t� ,ter �? 19 A" �J -1- V 18 0 .5-518 = This is volume change per °F (24) Digits per °F in test Volume change per digit. test Range (23) Compute to 4 decimal places. factor (a) 28. LOG OF TEST PROCEDURES 30. HYDROSTATIC PRESSURE CONTROL 31. VOLUME MEASUREMENTS M RECORD TO GAL 34' TEMPERATURE COMPENSATION USE FACTOR(a) 38. NET VAS CHANGES EACH READING 39.ACCUMULATED, CHANGE '17. DATE 28. Record details of settingU P and running test. (Use full length of line if needed.) 29. Reading No. Standpipe Level in Inches 32. Product in Graduate Product Replaced (-) 35. Thermal Sensor Reading 38. Change Higher + g Lower - (c) 37. Computation p x Expansion O + Expansion + Contraction - Temperature 1 At Nips I" record TOW End Deflection Beginning of Reading Level to which Restored Volume Varome Minus Expansion (+) or Contraction (-) #33(V) -#37(T) At low Lerel compute ewe per Now (NFPAcriteria) ftyE (24 hr.) Before Reading After Reading Product Recovered (+)