COMPLIANCE INFO_2006-2012 - Laserfiche WebLink

Home Browse Search

Fiber Glass Systems, 0 Bulletin B2102 May 1,2006 UUULC Listed Red Thread®II A Piping System General Specifications Primary Piping SECTION 1 :.S colve This section covers the use of fiberglass reinforced machined areas shall be protected from sunlight until plastic (FRP) pipe for single wall fuel handling and installed. fuel handling vent and vapor applications including 2.06 Acceptable Manyfacturers. Fiber Glass gasoline, unleaded gasoline, gasoline/alcohol Systems, Smith Fibercast, 501-618-2203, or approved mixtures, bio-diesel and diesel up to 150°F and 250 equal. psig cyclic pressure. Section 3-Material and Construction SECTIO 2- General Conditions 3.01 2"- " Pipe. The pipe shall be manufactured by 2.01 Coordination. Material furnished and work the filament winding process using an amine cured performed under this section shall be coordinated with epoxy thermosetting resin to impregnate strands of the related work and equipment specified under other continuous glass filaments, which are wound around sections, i.e. Valves, Flexible Connectors, Equipment. a mandrel at a 543/4" winding angle under controlled tension. The pipe shall be heat cured and the cure 2.02 Governing,Standards. Except as mofidifed or shall be confirmed using a Differential Scanning supplemented herein, all materials and construction Calorimeter. methods shall comply with and be tested in Pipe shall be supplied with a T.A.B.Tm (Threaded accordance with the following standards and test and Bonded) ends. methods: Pipe shall have a minimum continuous cyclic Standards and Test Methods pressure rating of 125 psig at 150°F in accordance UL971-2004 Standard for Nonmetallic with ASTM D2992, Procedure A or UL 971 pressure Underground Piping for Flammable rating. Liquids All pipe shall be 100% hydrotested at the factory ASTM D2310 Standard Classification for Machine- before shipment at a minimum pressure of 265 psig Made "Fiberglass" (Glass Fiber and shall be UL971-2004 Listed and labeled. Reinforced Thermosetting Resin) 3.02 ASTM D2310 Classifications (at 73.40F) Pipe 2"- 3" RTRP-11AF ASTM D2992 Standard practice for obtaining 4" RTRP-11AH Hydrostatic or Pressure Design Basis (Mechanical properties cell classifications shown are for Fiberglass" (Glass Fiber Reinf- minimums.) orced Thermosetting Resin) Pipe and Fittings 3.03 Fittings. All fittings shall be manufactured using the same type of material as the pipe. Fittings 2.03 eratin Conditions. In addition to the may be manufactured either by compression molding, above listed minimum tiondesign requirements,a clition the filament winding, resin transfer molding or contact . molding methods. All fittings, adapter, and sump system shall meet the following minimum operating penetrations shall be UL971-2004 Listed. conditions:a. Operating Pressure Fittings shall be adhesive bonded matched tapered bell and spigot. b. Fluid Conveyed 3.04 Connections. Connections to flex connectors c. Test Pressure or other piping materials shall be made by the use of NPT (National Pipe Thread) threaded adapters or 2.04 Quality Assurance. Pipe manufacturer's flanges bonded to the FRP piping system. quality program shall be in compliance with ISO 9001 3.05 Sum2 Penetrations. Sump penetrations shall and/orAPI Q1. be made by means of a permanently bonded FRP coupling. The coupling shall be capable of adjusting 2.05 DeliveM Storage. and Handling. Pipe and for the slope of the piping system entering or exiting fittings shall be protected from damage due to impact the sump wall. and point loading. Pipe shall be properly supported to 3-06 Adhesives. Adhesives shall be manufacturer's avoid damage due to flexural strain. The contractor standard for the piping system specified. shall not allow dirt, debris or other extraneous 3.07 Acceptable Products. RED THREAD IIA materials to get into pipe and fittings. All factory Piping System as manufactured by FGS Smith Fibercast or engineered approved equal. @ Trademark of Varco IIP,Inc. FIBER GLASS SYSTEMS•A NATIONAL OILWELL VARCO COMPANY http://www.smkhfibereast.com 2700 W.65th ST.,LITTLE ROCK,AR 72209.501-568-4010•FAX 501-568-4465 25 S.MAIN ST.,SAND SPRINGS,OK 74063•918-245-6651 •FAX 918-245-7566