COMPLIANCE INFO_2006-2012 - Laserfiche WebLink

Home Browse Search

Bulletin D4010 Fiber Glass Systeing- 0 April 15, 2007 7014, 7024 & 7069 Adhesive Kits For use with RED THREAD@ and UL-Listed RED THREAD IIA Piping Systems NOTE: This bulletin contains limited installation information. It is important to read and fully understand the instructions in Manual No.F6000 for standard products or Manual No.B2160 for UL-Listed products before beginning installation. 7014 Kit 7024 Kit 7069 Kit Contents Bonds Per Kit Contents Bonds Per Can' Contents Bonds Per Kit Pipe Pipe Pipe No. Size Size Size Description Qty. Inches No. Description Qty. Inches No. Description Qty. Inches 5 4 oz.Can Base 1 2 25 2.0 oz.Can Base 2 2 9 7 8 oz Can 1 6 8 Adhesive Adhesive Base Adhesive 1.5 oz.Container 1 3 18 0.6 oz. Container 2 3 6 23 oz Container 1 8 4 Hardener Hardener Hardener 1"PaintBrush1 4 10 V"Paint�Brush 2 4 4 2"Point Brush 1 10 3 Mixing Stick 1 6 6 Mixing Stick 2 6 2E Mixing Stick 1 4 2 Vinyl Gloves I pr. 1 8 3 Vinyl Gloves 2 pr. 8 1 Vinyl Groves 'I or 16 1 10 irs is rot =ee num , j.,nF 2 roral rot 155111 W 1=2 1 , The 7000 series adhesives are room temperature,two component,epoxy adhesive systems Once mixed,the adhesive's working life is limited to approximately 25 minutes at 75°F. Adhesive is recommended for use with FGS Smith Fibercast piping systems in recommended services where continuous service temperatures do not exceed 150°F. PRECAUTIONS containers without heavy gloves. This exothermic reaction will AFGS Smith Fibercast DOES NOT recommend testing generate a heavy, dense, foul-smelling smoke. The container of any installation with air or gas because of the safety should be placed outdoors in an open area until it cools. Avoid n! hazards created. inhaling smoke. Wear gloves and eye protection. Avoid contact with the adhesive Solvent containers may be under pressure. Use caution when and hardener since they are capable of causing skin and eye irrita- removing inner seals, especially in warm weather. Use eye tion. If contact is made, flush with water and wash with soap and protection. Concentrated vapors can be ignited. When using water. Avoid inhaling fumes. Work in a well ventilated area. solvent.do not smoke or use near an open flame. Use with ad- equate ventilation. Refer to the warning label on each container When adhesive is allowed to set up(harden)in the metal container, for additional information. the container may reach approximately 40011F. Do not handle hot POT LIFE OF ADHESIVE solvent. Do not put water or solvent in when necessary. The surfaces should the adhesive, be dry before applying adhesive. Once The pot life(working life)of an adhesive is the surfaces have been cleaned, do not the time it takes for the adhesive to begin - Reduce the concentrated mass by contaminate them by touching with hands. to harden in the mixing can. The life is removing the mixed adhesive from the can laying pipe in the dirt,etc. measured from the time the hardener and and spreading the adhesive into a thin film adhesive are first mixed. Though the pot onto a piece of tin or aluminum foil. This WARNING: Acetone and methyl ethyl life is quite short at high temperatures, it aids the dissipation of heat generated by ketone are extremely flammable. When becomes longer as the temperature drops the curing process. using these solvents,do not smoke or use below 75'F. near an open flame. Never use gasoline, The pot life of adhesive in hot weather can JOINT PREP turpentine,or diesel fuel to clean joints. be extended by keeping the adhesive cool A strong adhesive bond requires clean ADHESIVE MIXING or by reducing the concentrated mass of bonding surfaces. The bonding surfaces adhesive in the can. These can be easily must be free of oily fingerprints. dirt, oils, The ideal temperature range for mixing accomplished in the field as follows: grease and other contaminants. Freshly the adhesive base and hardener is 70 and tapered spigots or factory-fresh spigots and 80'F. • Cool the can by wrapping with rags or bells do not require cleaning unless visibly To mix. pour the entire contents of the paper towels.and then keep the wrappings contaminated. Soil or dirt may be removed hardener container into the adhesive wet with water or solvent. The can will by washing with water. Surfaces may be container. Mix the adhesive and hardener be cooled by evaporation of the water or cleaned with acetone or methyl ethyl ketone together with the wooden mixing stick. t Trademark of Varco I/P,Inc. FIBER GLASS SYSTEMS-A NATIONAL OIL ELL VARCO COMPANY 2700 W 65th ST,LITTLE ROCK,AR 72209.501-568-4410-FAX 501-56814465 25 S,MAIN ST,SAND SPRINGS,OK 74063 91.11-245JM51 -FAX 911-245-7156