COMPLIANCE INFO_1987-2006 - Laserfiche WebLink

Home Browse Search

UL Listed Centron® Fiberglass / Epoxy Pipe and Fittings ❑ Underwriters Laboratories, Inc. and Under- writers Laboratories of Canada have re - Gently completed the materials properties test and the physical test portion of their investiga- tion under UL subject 971 and ULC C107C- M1984 of Centron fiberglass / epoxy tubular products in size 2" and found it to comply with all applicable requirements for use with petro- leum products, alcohol, and alcohol -gasoline blends. UL file MH15635 and ULC file CMH 1301. ❑ Centron@ fiberglass / epoxy tubular products have the same excellent corrosion and physical properties as the Centron@ Oil Field products. The pipe, sleeve couplings, adapters, and reducer bushings are manufactured using the same filament winding process that has produced field proven tubular products for the past fifteen years. These products have been used by major and independent oil companies in service condi- tions up to 3,500 psi. ❑ Easy Installation - Centron@ fiberglass / epoxy tubular products are lightweight, easy to handle and install, and well suited for installation in underground fuel service piping systems and transmission lines. The bell and spigot piping systems are installed using Centron@ CAS -1 fuel and alcohol resistant adhesive specifically de- signed for this application. This adhesive was de- veloped for rapid installation with short cure time and maximum durability. Assembly of Cen- tron@ piping systems requires no special field 2 preparation except for tapering of field cut joints which is fully outlined in our installation instruc- tions. A full range of fittings and adapters are available. ❑ Pipe Products - Centron@ fiberglass / epoxy pipe products are filament wound on polished steel mandrels. The angle of the continuous fiberglass roving is precisely controlled to give the tubular products maximum performance capabilities. The epoxy resin matrix used in Centron@ fiberglass / epoxy products determines the mechanical, chemical, and thermal proper- ties of the products. The composite has a glass - to -resin ratio of 75:25 by weight and the glass/ resin system is matched for optimum physical and chemical resistance. The chemistry of the epoxy resin mix is strictly controlled and the curing cycle carefully monitored to ensure optimum chemical and physical properties of the finished product. ❑ Fittings - Centron@ epoxy fittings are the first to be manufactured using the state-of-the-art Resin Transfer Molding (RTM) technology. This process permits the use of long strand oriented reinforcement (as opposed to random oriented short strand reinforcement) and results in increased strength -to -weight ratios. Additionally, the proprietary RTM technique used to manufac- ture Centron@ RTM fittings produces parts with very low void content, excellent fiber wet out, and a resin rich inner surface for exceptional corrosion resistance. •0 • • 00 Piping 30'(9144) Nominal 15'(4572) Nominal (1) B 1-3/40 Taper 1-3/40 Taper (1) Some 15 foot lengths may have bonded coupling on bell end. Physical Description and Performance Values Pipe Size Designation Nominal I.D. Nominal Nominal O.D. Internal Ultimate Weight Minimum "B" Inch (mm) ASTM D-1599 Inch (mm) Wall Inch (mm) Pressure External Lbs/ft Bend Bell ASTM D-792 Flow Coefficient, C 150 thickness Rating (150°) Collapse (Kg/M) Radius O.D. Inch (mm) PSI (MPa) Pressure Ft (M) Inch (mm) PSI (MPa) 2 (50) CBS 300A 2.23 (56.6) .065(l.65) 2.36 (59.9) 300 (2.07) 155(l.07) .38 (.57) 75 (23) 2.5(64) *3 (76) CBS 225A 3.35 (85.1) .070J.78) 3.49 (88.6) 225(l.55) 85(.59) .60 (.89) 90 (27) 3.7(94) *4 (102) CBS 175A 4.33 (110) .075(l.91) 4.48 (113.8) 175(l.21) 48 (.33) .83 (1.24) 140 (43) 4.7(120) Physical and Mechanical Properties Property Value Test Method Axial Tensile Strength 12,000 PSI ASTM D-2105 Axial Tensile Modulus 6 1.8 x 10 PSI ASTM D-2105 Hoop Tensile Strength @ Weep 44,000 PSI ASTM D-1599 Long Term Hydrostatic Strength Cyclic (1.5 x 108cycles) @180° F Static (100,000 hrs) @75°F 8,106 PSI 28,114 PSI ASTM D-2992 Proc. A ASTM D-2992 Proc. B Axial Thermal Expansion -5 1.43 x 10 In/In/°F ASTM D-696 Density .07 LB/In 3 ASTM D-792 Flow Coefficient, C 150 Hazen -Williams 3 Fiberglass / Epoxy Fittings 90° Elbow, Bell x Bell 45° Elbow, Bell x Bell i ee, i5ell x i5en x i5en T B A Sleeve CouDlina. Bell x Bell 4 Size Inch (mm) A +or- 1/16" B Ref. 2 (50) 3.38 (86) 2.80 (71) *3 (76) 4.43 (113) 4.00 (102) *4 (102) 5.31 (135) 5.19 (132) Size Inch (mm) A +or- 1/16" B Ref. 2 (50) 2.73 (69) 2.80 (71) *3 (76) 3.46 (88) 4.00 (102) *4 (102) 4.06 (103) 5.19 (132) Size Inch (mm) A +or- 1/16" B Ref. 2 (50) 3.38 (86) 2.80 (71) *3 (76) 4.44 (113) 4.00 (102) *4 (102) 5.31 (135) 5.19 (132) Size Inch (mm) A +or- 1/16" B Ref. 2 (50) 6.00 (152) 2.55 (64) *3 (76) 6.50 (165) 3.65 (93) *4 (102) 7.00 (178) 4.65 (118)