Laserfiche WebLink
UL/ ULC f <br /> TERMINATION <br /> TEE 900 ELBOW 450 ELBOW SLEEVE COUPLING CONCENTRIC REDUCER <br /> _ F <br /> -+- -�- 1 D <br /> a—_ <br /> i 1 <br /> 1 A � Ee <br /> •—B t"�B ��LL <br /> TERMINATION CONCENTRIC REDUCERM SADDLES <br /> WITH 3/4"NPT SIZES AVAILABLE®� <br /> Belled Side Outlet Thrade®Side Outlel <br /> ..w1 NPT Internal TnreadalT <br /> 3"x2" 3"x1" ----- <br /> - - 3/4"NPT -11/4"x 2" 3"x " <br /> + TAP <br /> 4"x 3" 3"x 11/i" <br /> 4'.x 1'A" <br /> Sizes available for Termination Concentric Reducers, 4"x 1'h" <br /> with and without tap:3"x 2".4"x 3".'6"x 4". <br /> SIZES PRESSURE RATINGS Sending Properties of RED THREAD II Pipe <br /> A C =0E F i9 at Naninal ine Radiwm <br /> Size + t ht th.. <br /> e 1500 F size Tse F/24^c <br /> 50 fL <br /> 3" 6 7 14 3 2'h 21/2 3" 90 2" 15.2 m <br /> 80tt <br /> 4" I 7th 8 14 3 3 2'h 4" 80 3" 2 - <br /> 100 ff. <br /> 6"* 8 9 16 I 4 4 3 6"* 141 4" 30.5 m <br /> "'NOTE 6""secondary containment finings are not UL/ULC Listed. <br /> TYPICAL PHYSICAL TI " <br /> Property Value Value Test Method <br /> at 750 F 11,900 psi 82.05 MPa ASTM D-2105 <br /> Tensile Strength—Axial at 1500 F 9,300 psi 64.12 MPa <br /> Compressive Strength—Axial at 750 F 22,700 psi 156.51 MPa ASTM D-695 <br /> at 750 F 1.92 x 106 psi 1.32 x 104 MPa ASTM D-2105 <br /> Modulus of Elasticity in Tension at 1500 F 1.70 x 106 psi 1.17 x 104 MPa <br /> Ultimate Hoop Tensile Strength at Burst <br /> Average at 750 F 44,000 psi 303.37 MPa ASTM D-1599 <br /> Long Term Hoop Strength at 750 F 9.140 psi 63.02 MPa ASTM D-2992 <br /> Cyclic Pressure(150 x 106 cycles) at 1500 F 8,020 psi 55.30 MPa Procedure A <br /> Thermal Expansion Axial _ <br /> 2" 3" 4" pipe 1.09 x 10-5 in./in./OF 1.96 x 10-5 mm/mm/0C AOSI-TM16-3 <br /> Thermal Conductivity2 0 I d ( AOSI-TM16-15 <br /> 2" 3" 4"pipe 2.9 BTU/(ft. )(hr.)( F/in.) 0.42 W/(m)( K) <br /> Specific Gravity 1.85 1.85 I ASTM D-792 <br /> Flow Factor <br /> Hazen-Williams Coefficient 150 150 AOSI <br /> (1)A 3"x 2"reducer Dusmng which is (2)Threaded connections (3)Sharper bends should be eliminated (4)Data not avauabfe at time of (6)Pipe is manufactured in compliance <br /> not UL/ULC Listed is avaiiabie for must pe made with a to avoid stress concentration which printing, with ASTM 0-2996.Refer to general <br /> use witn me a . _ 'ermmation flexiote connector. would result in oremature pioefanure sDecitication sheet in catalog for the <br /> under oressure conditions (5)Tests run on oioe samoies. D-29%cesionauon code. <br />