Laserfiche WebLink
iLUL/ULC LISTED SECONDARY CONTA'INMENT FITTINGS <br />F0 <br />TERMINATION <br />TEE 900 ELBOW 450 ELBOW SLEEVE COUPLING CONCENTRIC REDUCER <br />F <br />P <br />D <br />C <br />Tc, <br />A <br />TERMINATION CONCENTRIC REDUCERV) <br />WITH 3/4" NPT <br />MOM- 3/4" NPT <br />TAP <br />Sizes available for Termination Concentric Reducers, <br />with and without tap: 3'*x 2", 4% 3". *6% 4". <br />SIZES <br />SIZES AVAILABLE <br />Gelled Side outlet <br />Threaded Side Outlet <br />NPT Internal ThreadsM <br />3"x2" <br />3"x1" <br />4" x 2" <br />3" x 11/4" <br />4" x 3" <br />3" X 1'12" <br />7 <br />4"x1" <br />3 <br />4" X 11/4' <br />21/2 <br />4" X 11h" <br />SIZ4 <br />psig at <br />150° Fl-', <br />'B <br />1/41, <br />C <br />'All <br />D <br />E <br />F <br />3" <br />6 <br />7 <br />14 <br />3 <br />21/2 <br />21/2 <br />4" <br />71/2 <br />8 <br />14 <br />3 <br />3 <br />21/2 <br />6" <br />8 <br />9 <br />16 <br />4 <br />4 <br />3 <br />*NOTE: 6" secondary containment fittings are not UL/ULC Listed. <br />PI—Tel 0 4 <br />PRESSURE RATINGS Bending Properties of RED THREAD 11 Pipe <br />Size <br />psig at <br />150° Fl-', <br />3" <br />90 <br />4" <br />80 <br />6" <br />tel <br />- TYPICAL "PHYSICAL*PROPERTIESX5.16)"-';-. <br />Minimum <br />Nominal <br />Bending adiu&13)- <br />Pipe Size <br />75* F/24* C <br />Tensile Strength Axial at 75° F <br />50 It. <br />2" <br />15.2 rn <br />at 150° F <br />80 It. <br />3" <br />24.4 m <br />Compressive Strength — Axial at 75° F <br />100 It. <br />4- <br />30.5 rn <br />- TYPICAL "PHYSICAL*PROPERTIESX5.16)"-';-. <br />Property, <br />Value <br />'Va Value. <br />.Test Method <br />Tensile Strength Axial at 75° F <br />11,900 psi <br />82.05 MPa <br />ASTM D-2105 <br />at 150° F <br />9,300 psi <br />64.12 MPa <br />Compressive Strength — Axial at 75° F <br />22,700 psi <br />156.51 MPa <br />ASTM D-695 <br />Modulus of Elasticity in Tension at 75° F <br />1.92 x 106 psi <br />1.32 x 104 MPa <br />ASTM D-2105 <br />at 150° F <br />1.70 x 106 psi <br />1.17 x 104 MPa <br />Ultimate Hoop Tensile Strength at Burst <br />Average at 75° F <br />44,000 psi <br />303.37 MPa <br />ASTM D-1599 <br />Long Term Hoop Strength at 75° F <br />9,140 psi <br />63.02 MPa <br />ASTM D-2992 <br />Cyclic Pressure (150 x 106 cycles) at 150° F <br />8,020 psi <br />55.30 MPa <br />Procedure A <br />Thermal Expansion Axial <br />2" 3" 4" pipe <br />1.09 X 10-5 in./in./°F <br />1.96 x 10-5 mm/mm/OC <br />AOSI-TM16-3 <br />Thermal Conductivity <br />2" 3" 4" pipe <br />2.9 BTU/(ft.2)(hr.)(*F/in.) <br />0.42 W/(m)(*K) <br />AOSI-TM16-15 <br />Specific Gravity <br />1.85 <br />1.85 <br />ASTM D-79 <br />Flow Factor <br />Hazen -Williams Coefficient <br />150 <br />150 <br />AOSI <br />(1) A 3"x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at time of (6) Pipe is manufactured in compliance <br />not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing. with ASTM D-2996. Refer to general <br />use with the 4"x 3" termination flexible connector. would result in premature pipe failure specification sheet In catalog for the <br />concentric reducer. under pressure conditions. (5) Tests run on pipe samples. D-2996 designation code. <br />7 <br />