Laserfiche WebLink
UL/ULC Listed Red Thread, Piping System • <br /> RED THREAD IIA PIPING <br /> RED THREAD IIA Primary Piping RED THREAD IIA Secondary Containment Piping <br /> Nom.Pipe Pipe Nom.Pipe Pipe <br /> a i Size Part Length Size Part Length <br /> (In./mm) Number (ft.) (In.1mm) Number (rt.) <br /> 2 011020-069-1 15 3 011030-069-4 15 <br /> 2 011020-069-2 22-25 3 011030-069-5 22-25 <br /> 2 011020-069-3 26-30 3 r. 011030-069-6 26-30 <br /> 3 011030-069-1 15 4 1 '_ 011040-077-5 15 <br /> 3 c.. 011030-069-2 22-25 4 1 011040-069-5 22-25 <br /> 3 c._ 011030-069-3 26-30 4 1 �== 011040-077-6 26-30 <br /> 4 011040-071-1 15 6 1i`2 011060-120-5 15 <br /> 4 011040-069-2 22-25 6 1 : 011060-120-4 22-25 <br /> 4 011040-071-3 26-30 6 1- 011060-120-6 26-30 <br /> DIMENSIONAL DATA <br /> Nominal Nominal Mill <br /> Pipe Nominal Nominal Wall Nominal Pressure/ Test External Pressure <br /> Size I.D. O.D. Thickness Weight Temperature Pressure Max.Rating(psig/MPa) <br /> (inlmm) (in.linm) (in.lmm) (in.1mm) (lbs./tt.Akg_rn) Max.Rating (psig/MPa) 75°F/24°C 150°F/66°C <br /> 2 2.235 2.375 .070 0.5 250 psig @ 150°F 375 85 80 <br /> 3 3.360 3.500 .070 0.7 175 psig @ 150'F 300 36 34 <br /> f'ti k�` rpt' <br /> 4 4.360 4.560 .085 1.2 125 psig @ 150°F 265 34 30 <br /> 6 6.408 6.678 .135 2.4 NA 265 22 20 <br /> 1 c� <br /> TYPICAL PHYSICAL PROPERTIES{" <br /> PROPERTY RED THREAD®IIA Pie Bending Radius,Minimum <br /> t.1Pa Viz-24°C psi 150°F MPa a)66 C Nominal <br /> psi�75°F p @ G--�'" Pipe Size 2" 3" 4" 6" <br /> Axial Tensile(ASTM D2105) inches <br /> Ultimate Stress 10,300 8,200 <br /> Design Stress 2,575 2,050 1 Ft. 75 110 140 204 <br /> Modulus of Elasticity 1.82 x 101 %��l 1.42 x 106 <br /> Axial Compression(ASTM D695) 33,300 25,600 m <br /> Ultimate Stress 8,300 <br /> Design Stress 6 89 X0006 <br /> Modulus of Elasticity 1.26x 10 <br /> (1) All values except pressure-temperature <br /> Beam Bending(SFPTM) maximum rating are nominal values.Tolerances or <br /> Ultimate Stress 23,000 1_;;-G 19,200 maximum/minimum limits can be obtained from Smith <br /> Design Stress�h 2,900 2,400 Fibercast. <br /> Modulus of Elasticity 2.18x 106 1.70 x 106 1 (2) All sizes can accept full vacuum pressures at <br /> (Long Term per ASTM D2925) maximum temperature ratings. <br /> (3) Ultimate and allowable design stresses are <br /> Hydrostatic Burst(ASTM D1599) based on minimum reinforced wall thickness.Pipe is <br /> Ultimate Hoop34000 39,200 manufactured in compliance with ASTM D2996. <br /> , <br /> Tensile Stress (4) Design bending stress is 118 of ultimate to <br /> account for combined stress(i.e.bending and <br /> Hydrostatic Design(ASTM D2992) 2"-3" 2"&3" Z pressure). <br /> ProcedureA 9,410fe a 7,400f0 (5) Design stress is based on long term cyclic fatigue <br /> Cyclic 150 x 106 4"-6' 1' 4"-5' data using ASTM D2992 test method.However,all <br /> Cycles 13,0401e 10,450 L.1 testing is not complete attimeof printing. <br /> (6) For RED THREAD IIA pipe the hydrostatic <br /> Coefficient of Linear 0.88 x 105 in./in./*F cyclicdesign stresswas determined at 150°and <br /> Thermal Expansion(SFPTM) "����` � 200°F,perASTM D2992 Procedure A.Based on this <br /> data,the extrapolated value at 75°F is 13,030 psi. <br /> Specific Gravity 1.8 <br /> Flow Factor (7) For RED THREAD IIA pipe the hydrostatic cyclic <br /> design stress was determined at 75°and 200°F,per <br /> Hazen-Williams Coefficient 150 ASTM D2992 Procedure A.Based on this data,the <br /> extrapolated value at 150'F is 7,400 psi. <br /> 4 <br />