Laserfiche WebLink
LUUULC LISTED <br />SECONDARY <br />TERMINATION <br />TEE 900 ELBOW 450 ELBOW SLEEVE COUPLING CONCENTRIC REDUCER <br />x�rxd$�i fF`Fsr)�de3':',i't D ${ Q <br />TERMINATION CONCENTRIC REDUCERIO <br />WITH 3/4" NPT <br />I , htv�.' 3/4" NPT <br />f TAP <br />Sizes available for Termination Concentric Reducers, <br />with and without tap: 3"x 2", 4"x 3", *6"x 4". <br />SIZES <br />Size <br />A <br />:v: B <br /><+ ,; <br />6 <br />7 <br />14 <br />3" <br />71/2 <br />8 <br />14 <br />4" <br />8 <br />9 <br />16 <br />6"* <br />SIZES AVAILABLE <br />Belied sae Outlet <br />Threaded side Outlet <br />NFT Ini—I Threada121 <br />3"x2" <br />3"x 1" <br />4" x 2" <br />3" x 11/4" <br />4"x3" <br />3"x1�/i' <br />4 <br />4"x 1" <br />3 <br />4" x 11/4" ' <br />24.4 m <br />4" x 1'h" <br />D <br />E <br />Size <br />3 <br />21/2 <br />21/2 <br />3 <br />3 <br />21/2 <br />4 <br />4 <br />3 <br />*NOTE: 6" secondary containment fittings are not UL/ULC Listed. <br />PRESSURE RATINGS <br />SADDLES <br />,,. rC yiiir i� 9 t T <br />Bending Properties of RED THREAD II Pipe <br />psig at ;. <br />Size <br />150° <br />3" <br />90 <br />4" <br />80 <br />6"* <br />141 <br />SADDLES <br />,,. rC yiiir i� 9 t T <br />Bending Properties of RED THREAD II Pipe <br />-". � 1 , :: SA`4 ,�1v q. 3'4 iy.: -. -i'. L Y.� :.._ t.. :.: ,., :..:.. '.-.:: i Y .:...1 yy, S f fi ! J✓ ; � i ! �i�v .t4; <br />Mlnitnu n <br />Nominal <br />Bending Radiusl'1 <br />}Pipe Slze <br />';76* F/24* C <br />Tensile Strength — Axial at 75° F <br />50 I L <br />2„ <br />15.2 m <br />at 150° F <br />80 Ill. <br />t <br />64.12 MPa <br />24.4 m <br />Compressive Strength — Axial at 75° F <br />100 It. <br />4" <br />30.5 m <br />-". � 1 , :: SA`4 ,�1v q. 3'4 iy.: -. -i'. L Y.� :.._ t.. :.: ,., :..:.. '.-.:: i Y .:...1 yy, S f fi ! J✓ ; � i ! �i�v .t4; <br />ATYPICAL' P.HYSICAL�'PROPERTIES <br />Property ° . <br />: Value <br />Value k , <br />Test`Method <br />Tensile Strength — Axial at 75° F <br />11,900 psi <br />82.05 MPa <br />ASTM D-2105 <br />at 150° F <br />9,300 psi <br />64.12 MPa <br />Compressive Strength — Axial at 75° F <br />22,700 psi <br />156.51 MPa <br />ASTM D-695 <br />at 75° F <br />Modulus of Elasticity in Tension <br />1.92 x 106 psi <br />1.32 x 104 MPa <br />ASTM D-2105 <br />at 150° F <br />1.70 x 106 psi <br />1.17 x 104 MPa <br />Ultimate Hoop Tensile Strength at Burst <br />Average at 75° F <br />44,000 psi <br />303.37 MPa <br />ASTM D-1599 <br />Long Term Hoop Strength at 75° F <br />9,140 psi <br />63.02 MPa <br />ASTM D-2992 <br />Cyclic Pressure (150 x 106 cycles) at 150° F <br />8,020 psi <br />55.30 MPa <br />Procedure A <br />Thermal Expansion Axial <br />2" 3" 4" pipe <br />1.09 x 10-5 in./in./°F <br />1.96 x 10-5 mm/mm/°C <br />AOSI-TM16-3 <br />Thermal Conductivity <br />2" 3" 4" pipe <br />2.9 BTU/(ft.2)(hr.)(°F/in.) <br />0.42 W/(m)(°K) <br />AOSI-TM16-15 <br />Specific Gravity <br />1.85 <br />1.85 <br />ASTM D-792 <br />Flow Factor <br />Hazen -Williams Coefficient <br />150 <br />150 <br />AOSI <br />(1) A 3"x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at time of (6) Pipe is manufactured in compliance <br />not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing. with ASTM 0-2996. Refer to general <br />use with the 4"x 3" termination flexible connector. would result in premature pipe failure specification sheet in catalog for the <br />concentric reducer. under pressure conditions. (5) Tests run on pipe samples. D-2996 designation code. <br />