COMPLIANCE INFO_1989-2008 - Laserfiche WebLink

Home Browse Search

ou�onwomm10 October 1.znou FiberGlass— — --�� ^�� ~�� N�~�� . _ ' ' , ' -~__ - ~— ' ~,~~~ Adhesive ~ ~.�~ For use with RED THREAD@Uand ULListed RED THREAD IIA piping systems. NOTE: This bulletin contains limited installation information.It is important that you read and fully dnstanuthm instructions inManual No.F600ofor standard products, orManual No.B2160for WL Listed products,before beginning your installation. 7014 Kit 7024 Kit 7069 Kit Contents Bonds per Kit Contents Bonds per Kr Contents Bonds per Kit Pipe Pipe Pipe Size No. Size No. Size No. Description Qty. (in.) Bonds — Description City. (in.) Bonds Description Qty. (in.) Bonds 5.4 oz.Can Base Adhesive 1 2 25 2.0 oz.Can Base Adhesive 2 2 18 7.8 oz.Can Base Adhesive 1 6 8 1.6 oz.Container Hardener 1 3 18 0.6 oz.Container Hardener 2 3 10 2.3 oz.Container Hardener 1 8 4 Stir Stick 1 a 3 Stir Stick 2 Stir Stick 1 14 2 Vinyl Gloves 1 pr. Vinyl Gloves 2 pr. Vinyl Gloves 1 pr. *Total mboth kits. The rmmseries adhesives are room temperature,two component,epoxy aon piping systems in recommendedservices where continuous service temperatures sive systems. Once mixed,the adhesive's working life.ylimited m approximately u^not exceed 150'r. zominutes atm^p. The adhesive mrecommended ux"oemmamnhp/u*mam PRECAUTIONS ter. Avoid inhaling fumes. Work in a well Solvent Containers may be under pres- ASmith Fibercast recommends that you ventilated area. Asure. Use caution when removing in- ner seals,especially in warm weather. Use DO NOT test any installation with air When adhesive is allowed to set up eye protection. Trichloroethylene is not clas- or gas because of the safety hazards creat- LN (harden)in the metal container,the sified as flammable;however,concentrated ed. container may reach approximately 4007. vapors can be ignited. When using this sol- AWear gloves and eye protection. Do not handle hot containers without heavy vent,do not smoke or use near an open Avoid contact with the adhesive and gloves. This exothermic reaction will gener- flame. Use with adequate ventilation. Refer hardener,since they are capable of causing ate a heavy,dense,foul-smelling smoke; to the warning label on each container for ad- skin and eye irritation. If contact is made, therefore,the container should be placed ditional information. flush with water and wash with soap and wa- outdoors in an open area until it cools. Avoid inhaling smoke. JOINT PREP near onopen flame Never use gaao' 1 For best results,base adhesive and line,turpentine,ordiesel fuel k/clean hardener should bobetween 7U~Fand 1 Cleaning the bonding surface ixre- joints. 1OO^Fbefore mixing. quimUonly when the bonding surfaces, on either i fittings, h b Once ou�aooshave been cleaned,de 2 PourenUr000n�en�eofhordnnor ' not contaminate them bytouching with container into the adhesive container �prints,—t -' ~�hx- ' `tapered dirt,i finger-ots or` hands, laying pipe in the dirt. oto. (see Fig. 1.0). Contaminated ov�ooeowixcause a factory-fresh spigots ° -~'~'^cleaning ~~~ poo bond. 3 Mix the adhesive and hardener -- ^ ~'^ `'~~'� to- contaminated. For dirt contamination, Make sure the solvent has ovaporategethorwiththowoodonmixingn8okd . washing with water is acceptable. from the bonding surfaces before apply- Cleaning with solvent is optional. ingadhnoiwe. Acceptable solvents are momumoxyl' nno.um»mne.ormmuxy|omylketono. ADHESIVE MIXING WARNING: Acetone and methyl SOLVENT DISPOSAL:Solvent is classified as a Aethyl ketone are extremely flam' hazardous waste and cannot be dumped.It can be mebie. When using these Sol- use.Empty solvent cans meet EPA regulations for vents, do not smoke or use ner.These guidelines are based on federal regula- tions.State and local regulations and ordinances should be reviewed. Figure 1.0 upu: hon:m°ww.ommmummmm.com Fiber GlassSystems NATIONAL muweLLvAnooCOMPANY unmw.xoHar.LITTLE ROCK,xn72u09*s92`m1-5ao* 10^pAX501-568-446