Laserfiche WebLink
SWRCB, January 2002 <br />Page 6 of 8 <br />7. UNDER-DISPENSER CONTAINMENT (UD9 TESTING <br />Test Method Developed By: <br />U UDC Manufacturer <br />U Other (Spec) <br />IXlndustry Standard U Professional Engineer <br />Test Method Used: <br />U Pressure <br />U Other (Spec) <br />U Vacuum <br />Mydrostatic <br />Test Equipment Used: <br />UDC Manufacturer: <br />UDC# 1&2 <br />I? <br />UDC# 3&4 <br />7 <br />Equipment Resolution: <br />UDC# 5&6 <br />? <br />UDC# 7&8 <br />? <br />UDC Material: <br />Plastic c <br />Pl stir <br />Plastic <br />UDC De the <br />1211 <br />ee <br />Height from UDC Bottom to Top <br />of Highest Piping Penetration: <br />Bottom <br />Bottom <br />Bottom <br />Bottom <br />Height from UDC Bottom to <br />Lowest Electrical Penetration: <br />Bottom <br />Bottom <br />Bottom <br />. e <br />Bottom <br />Condition of UDC prior to <br />testing: <br />Dirt /Dr <br />Dirty/Dry <br />Dirty/Dry <br />Dirty/Dry <br />Portion of UDC Tested <br />Does turbine shut down when <br />UDC sensor detects either <br />product or water?* <br />U Yes U No XJ NA <br />U Yes U No DENA <br />Utes U No LINA <br />U Yes U No LXNA <br />Turbine shutdown response time <br />A <br />A <br />Is system programmed for fail- <br />safe shutdown?* <br />U Yes U No X1 NA <br />Utes UNo LNNA <br />Utes 'U No X_INA <br />UYes UNo INA <br />Was fail-safe verified to be <br />operational?* <br />U Yes U No NA <br />Utes U,40INNA <br />Utes UNo AU NA <br />UYes UNo IRNA <br />Wait time between applying <br />pressure/vacuum/water and <br />starting test <br />hr. <br />hr. <br />2 hr. <br />hr. <br />Test Start Time: <br />12:15 <br />12:20 <br />1:20 <br />1 1:40 <br />Initial Reading R: <br />0 <br />0 <br />0 <br />0 <br />Test End Time: <br />__2__L5 0 <br />12:10 <br />Final Reading (RF): <br />Test Duration: <br />Chan&e in Readin RSR, <br />Pass/Fail Threshold orCriterla: <br />Test Result: <br />XJ Pass U Fall <br />E Pass U Fall <br />N Pass U Fail <br />IX Pass U Fall <br />Was sensor removed for testing? <br />U Yles 11 No LWA <br />U Yes U No D(NA <br />U Yes U No IRNA <br />U Yes U No 1XNA <br />Was sensor properly replaced and <br />verified functional after testin ? <br />p Yes 0 No IMA <br />U Yes UNo IXNA <br />U Yes U No 1XNA <br />U Yes U No 1XNA <br />Comments — (include information on repairs made prior to testing, and recommended follow-up forfailed tests) <br />e If the testing method does not test the entire depth of the UDC, specify how much of the UDC was tested. Methods not testing the <br />entire UDC should only be used if the monitoring system provides fail-safe turbine shutdown. (See SWRCB LG -160) <br />2 With the submersible pump running, place the sensor in product (discriminating sensors should also be placed in water). The time <br />between placing the sensor in product and the turbine shutting down is the response time. This should be done if the secondary <br />containment testing method used does not test the entire volume of the UDC <br />This information is not needed if the entire UDC is tested. <br />