COMPLIANCE INFO_1992-2000 - Laserfiche WebLink

Home Browse Search

UL/ULC LISTED SECONDARY •'e1. TERMINATION CONCENTRIC REDUCERM WITH 3/4" NPT 3/4" NPT + TAP Sizes available for Termination Concentric Reducers, with and without tap: 3" x 2", 4" x 3", •6" x 4" SIZES SIZES AVAILABLE Belled side outlet Threaded Side outlet NPT Internal Threads(2) 3„x2„ 3„x1„ 4" x 2" 3" x 11/4" 4" x 3" 3" x 11/2" 6 4"x1" 14 4" x 11/4" 21/2 4" x 1lh" Ul *NOTE: 6" secondary containment fittings are not UL/ULC Listed. PRESSURE RATINGS SADDLES Bending Properties of RED THREAD 11 Pipe Sse A f 'A = B C D -qAy Propertya. 50 IL 3" 6 7 14 3 21/2 21/2 4" 71/2 8 14 3 3 21/2 Compressive Strength — Axial at 750 F 6"* 8 9 16 4 4 3 Ul *NOTE: 6" secondary containment fittings are not UL/ULC Listed. PRESSURE RATINGS SADDLES Bending Properties of RED THREAD 11 Pipe (1) A 3" x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at time of (6) Pipe is manufactured in compliance not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing, with ASTM 0-2996. Refer to general use with the 4-x 3" termination flexible connector. would result in premature pipefailure specification sheet in catalog for the concentric reducer. under pressure conditions. (5) Tests run on pipe samples. D-2996 designation code. 7 Minimum �� NomfnaC� Bending Radiusni aPlpe Siie 75' F/2C° C -qAy Propertya. 50 IL 2„ 15.2 m x 80 I L 3„ 24.4 m at 750 F Tensile Strength —Axial 100 It. 4„ 30.5 m (1) A 3" x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at time of (6) Pipe is manufactured in compliance not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing, with ASTM 0-2996. Refer to general use with the 4-x 3" termination flexible connector. would result in premature pipefailure specification sheet in catalog for the concentric reducer. under pressure conditions. (5) Tests run on pipe samples. D-2996 designation code. 7 TYP CA PHYSIC�kLPRQPERTIES A -qAy Propertya. Value Value Method x .,aTest at 750 F Tensile Strength —Axial 11,900 psi 82.05 MPa ASTM D-2105 at 1500 F 9,300 psi 64.12 MPa Compressive Strength — Axial at 750 F 22,700 psi 156.51 MPa ASTM D-695 at 750 F 1.92 x 106 psi 1.32 x 104 MPa Modulus of Elasticity in Tension ASTM D-2105 at 1500 F 1.70 x 106 psi 1.17 x 104 MPa Ultimate Hoop Tensile Strength at Burst Average at 750 F 44,000 psi 303.37 MPa ASTM D-1599 Long Term Hoop Strength at 750 F 9,140 psi 63.02 MPa ASTM D-2992 Cyclic Pressure (150 x 106 cycles) at 1500 F 8,020 psi 55.30 MPa Procedure A Thermal Expansion Axial 2" 3" 4" pipe 1.09 x 10-5 in./in./OF 1.96 x 10-5 mm/mm/OC AOSI-TM16-3 Thermal Conductivity 2" 3" 4" pipe 2.9 BTU /(ft.2)(hr.)(0F/in.) 0.42 W/(m)(OK) AOSI-TM16-15 Specific Gravity 1.85 1.85 1 ASTM D-792 Flow Factor Hazen -Williams Coefficient 150 150 AOSI (1) A 3" x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at time of (6) Pipe is manufactured in compliance not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing, with ASTM 0-2996. Refer to general use with the 4-x 3" termination flexible connector. would result in premature pipefailure specification sheet in catalog for the concentric reducer. under pressure conditions. (5) Tests run on pipe samples. D-2996 designation code. 7