Laserfiche WebLink
Easy Installation! The 3"inlet of the 99 LD-3000 allows the leak detector to be installed in the discharge port of <br /> 3-5 HP submersible pumps. The discharge of the 99 LD-3000 is 3"male thread; Height- 16.25 inches. Width-7.86 <br /> inches.Weight-29 pounds; Can be installed by one person. Now with easy access to check valve for field replacement. <br /> The 99 LD-3000 is available with flange fittings instead of threads as Part#99 LD-3000\FL. <br /> Integrated In-Line CheckValve/Pressure Relief: Allows the leak detector to compensate for a defective <br /> submersible pump pressure relief or check valves that allow drain-back into tanks. The integrated pressure relief valve <br /> of the 99 LD-3000 will hold 30 PSI in the line by itself. <br /> One Way Poppet Flow Path I Isolates pump turbulence from line leak detection at pump start-up. The hardened <br /> stainless steel poppet does not dimensionally change due to thermal conditions encountered during station operation <br /> (precision metering change is insignificant down to-20 degrees F). <br /> Reverse Ratio Piston/Poppet Combination: The leak detector has a smaller diameter piston area than <br /> the poppet it is attached to. This allows the leak detector to stay in the fast fill position (3 GPM)to a higher pressure <br /> while compressing vapor pockets and stretching flexible line faster, resulting in less time to full flow. <br /> Smaller Volume / Faster Response Piston Size: Results in one-fourth the volume of fuel to replace <br /> when in leak search and one-fourth the volume to return to the line when pump is turned off. T <br /> faster full flow to dispensers and faster resets to detect leaks. RI <br /> CCEVE <br /> OCT 3 1 2014 <br /> Technical Specifications 99 LD-3000 <br /> ENVIRONMENTAL HEALTH <br /> Fuels: - Gasoline,100%®methanol*,100%ethanol*,up to 15%MTBE 7.86 Li"ARTNIENT <br /> * Any combination of the above <br /> * #1 or#2 diesel,kerosene,Jet A*or JP-4*,AV Gas* <br /> and Blodiesel*(all blends). <br /> When used with Blodiesel,any alcohol fuel concentration above20%,JetA,JP-4,or <br /> AV Gas,order part#LD3-SSVS for stainless steel fittings and stainless steel vent <br /> tubing.For chemical applications other than those listed above,contact factory. <br /> Certified to meet EPA 3 GPH @ 10 PSI: <br /> • Rigid pipe up to 406 gal.,1171 ft.of 3"id. <br /> • Flexible pipe up to 96 gal.,260 ft.of 3"id. TEST <br /> • Combination of Rigid and Flexible pipe up to 502 gal., 1431 ft.of 3"id. _-PORT <br /> A <br /> Construction: Forged steel body;Steel alloy;Forged steel threads. (PUAP PPESSIRE) <br /> Cylinder Assembly: Anodized 6061-T6 Aluminum <br /> Internal Parts: Anodized 2011-T3 Aluminum, 6061-T6 Aluminum; <br /> Acetron GP;CDSM 1026 and DOM 1026 steel; 8.75 Tf ST <br /> PORT <br /> 17-4 stainless steel 3. MALC "\T B <br /> Seals: Low drag, stainless steel spring energized teflon seals 0 <br /> T <br /> 0 Rings: U.L.Approved V9702-Viton Type B Fluorocarbon 5 N'.) <br /> 'P <br /> I/ I' T <br /> Metering Pin and Poppet: 17-4 stainless steel TYP 11 CAL <br /> CheckValve: Acetron GP,Viton F Seal 3' MALE NPT-/ <br /> Pressure Relief: Stainless Steel,29 PSI pressure relief. This pressure is in <br /> addition to the pump pressure relief. <br /> Inlet: 3"male Outlet: 3"male <br /> • Certified to handle 12+feet of head pressure. <br /> • Exceeds EPA specifications for 3 GPH @ 10 PSI hourly test. <br /> • Vent line must be unobstructed,leak fight and connected to headspace of tank,not to be subjected <br /> to pressure or vacuum. <br /> • Combination line check1pressure relief prevents drainage into the tank. <br /> VM Vaporless Manufacturing, Inc. Toll Free: 1-800-367-0185 <br /> 8700 East Long Mesa Drive Phone: (928) 775-5191 <br /> Prescoft Valley,Arizona 86314 Fax: (9 28) 775-5309 <br /> Web Site: www.vaporiess.com e Email: vmi@vaporiess.com <br />