COMPLIANCE INFO_1999-2007 - Laserfiche WebLink

Home Browse Search

HARDWARE AND ANCHORING POINTS Anchoring hardware and anchor points must be sized according to Table 7-3 and manufactured to industry standards and 0 WARNING: 191 dimensions.The installing contractor is responsible for providing Do not use air pressure to test tanks that contain flammable or hardware and anchor points of sufficient strength.The particular combustible liquids or vapors,and do not perform any post- configuration of hardware will be determined by the owner or the installation pressure test. The fuel/air mixture may explode and owner's representative. Locate the anchor points as shown in cause death,severe personal injury or property damage.Tanks Table 7-2 and Figure 7-2. Refer to dimension"E".Align all anchor that will be ballasted with a flammable product should be air points with the marked(><)location on the tanks,within a tested before ballasting, tolerance of± 1 inch. For specific information on hardware and its �jWARNING: use,consult the hardware manufacturer. 0 TI If product is used as ballast,exercise special care in handling. Safeguard against sparks,fire or product spills.Improper Use only appropriate sized hardware with the strap eye. handling of product can cause a fire or explosion,and may Oversized hardware may damage the strap eye and result in result in death,severe personal injury or property damage. personal injury or property damage.See Figure 7-4 for strap eye dimensions. INTERMEDIATE DEFLECTION MEASUREMENT After backfill is brought to the top of the tank,make an MINIMUM TURNBUCKLE DIAMETER MINIMUM intermediate measurement of vertical deflection according to the TANK (BYTYPE) WIRE ROPE instructions in Section 13. DIAMETER HOOK JAW EYE DIAMETER TEST 4' 3/4" 1/2" 1/2" 3/8" After the tank has been measured and vertical deflection is 6' 3/4" 1/2" 1/2" 3/8" determined to be within the limits specified by Xerxes,the tank 8' 11/4" 3/4" 3/4" 1/2" must be pressure tested to ensure that no damage occurred during installation.The procedure in Section 2 Pre-installation 10' 11/4" 3/4" 3/4" 1/2" Testing should be followed,soaping all exposed areas of the tank 12' 11/4" 3/4" 3/4" 1/2" and all fittings. Because most of the tank exterior is no longer visible,the tank TABLE 7-3 must be tested by checking the gauge for one hour at the test manifold for any drop in pressure.Carefully relieve the pressure in the tank and remove the Quick Disconnect assembly from dry 31/4" Double Wall tanks. T:: -rte 0 WARNING: _f Do not use air pressure to test tanks that contain flammable or combustible liquids or vapors and do not perform any post- installation pressure test.The fuel/air mixture may explode and cause death,severe personal injury,or property damage. FIGURE 7-4 Tanks that will be ballasted with a flammable product should be air tested before ballasting. NOTE:Drop-forged type turnbuckle may be used in place of all or a portion of Zt, WARNING: wire rope. NOTE:All exposed metal on the holddown straps,turnbuckles and/or threaded If product is used as ballast,exercise special care in handling. rod must be coated or galvanized to prevent corrosion(Figure 7-4A). Safeguard against sparks,fire or product spills.Improper NOTE:When fastening wire rope,use a minimum of three clamps on each joint. handling of product can cause a fire or explosion,and mayresult in death,severe personal injury or property damage. Use shackle-type or chair-type clamps as appropriate(Figure 7-4A). The tank may be ballasted after the backfill is even with the top of the tank and post-installation testing,if applicable,has been successfully completed.Only under wet-hole conditions,as described in Section 6,should ballast be added before the backfill is even with the top of the tank.When filling the tank,make sure FIGURE 7-4A the tank is properly vented.The vent must be large enough to allow the displaced air to escape. o.•e• IINI= =11111-11111=11111- 11111=11111-11111-11111-11111-11111