Laserfiche WebLink
A <br /> Nominal Nominal Nominal. Nominal Nominal Mill Test External Pressure Random <br /> Pipe Size13t O.D. I.D. Wall Thickness Weight Pressure-Temp. Pressure Max.Rating psi /MPa) Lengths <br /> (in.) (in./-!:::) (in./ ::-i) (in./r,-) (lbs.-H./'; - ) Max.Rating (psig) 75°F/_. c 1501F/;3 (H./c) <br /> 2 2.375 2.235 0.070 0.4 250 psig @ 150°F 375 88 79 15 30 <br /> 2%iF_'�Z 56.3 C54 <br /> .. <br /> 3 3.500 3.360 0.070 0.6 175 psig @ 150°F 265 29 24 15 30 <br /> 4 4.500 4.360 0.070 0.8 125 psig @ 150°F 265 34 30 15 30 <br /> (1) All values except pressure-temperature maximum (2).All sizes can accept full vacuum pressures at (3) UL Listed 5"secondary containment piping and <br /> rating are nominal values.Tolerances or maximum/ maximum temperature ratings. Non-UL Listed 6"secondary containment piping are <br /> minimum limits can be obtained from Smith also available from Smith Fiberglass Products Inc. <br /> Fiberglass Products Inc. <br /> 2"&3" 4„ <br /> PROPERTY RED THREAD®IIA Pipe RED THREAD®IIA Pipe <br /> psi @ 75°F psi @ 150°F ?; psi @ 75°F psi @ 150°F <br /> Axial Tensile(ASTM 105) <br /> Ultimate Stress 13,200 11,600 :_. 15,200 11,700 <br /> Design Stress 3,300 =_.? 2,900 _:.= 3,800 _-. 2,925 <br /> Modulus of Elasticity 2.08 x 106 1.95 x 106 1.80 x 106 = 1.11 X 106 '.. <br /> Axial Compression(ASTM D695) <br /> Ultimate Stress 18,760 _ ._ 14,280 :_.= 33,300 __:._ 25,600 ._ <br /> Design Stress 4,690 3. 3,570 _ .. 8,300 ? 6,400 <br /> Modulus of Elasticity 1.02 x 106 0.91 x 106 _. . 1.26 x 106 89 x 106 _ <br /> Beam Bending(SFPTM) <br /> Ultimate Stress 18,880 17,290 23,000 NA <br /> Design Stressl51 2,360 2,160 2,900 1,800 <br /> Modulus of Elasticity 1.70 x 106 1.20 x 106 2.18 x 106 1.79 x 106 :? <br /> (Long Term per ASTM D2925) <br /> Hydrostatic Burst(ASTM D1599) <br /> Ultimate Hoop 29,860 __ . . 60,340 :.. 35,000 41,000 <br /> Tensile Stress <br /> Hydrostatic Design(ASTM D2992) <br /> Procedure A <br /> Cyclic 150 x 106 NA 6,470161 at 10,450 _. <br /> Cycles <br /> Coefficient of Linear <br /> Thermal Expansion(SFPTM) 1.12 x 10-5 in./in./°F 0.88 x 10-6 in./in./°F <br /> Specific Gravity 1.8 1.8 ` <br /> Flow Factor <br /> Hazen-Williams Coefficient 150 150 <br /> (4) Ultimate and allowable design stresses (5) Design bending stress is 1/8 of (6) Design stress is based on long term (7) For 4"RED THREAD®IIA pipe the <br /> are based on minimum reinforced wall ultimate to account for combined cyclic fatigue data using ASTM D2992 hydrostatic cyclic design stress was <br /> thickness.Pipe is manufactured in stress(i.e.bending and pressure). test method.However,all testing is not determined at 150°and 200°F,per ASTM <br /> compliance with ASTM D2996. complete at time of printing. D2992 Procedure A.Based on this data, <br /> the extrapolated value at 75°F is 13,040 <br /> Bending Radius,Minimum psi. <br /> Nominal <br /> It is the policy of Smith fiberglass Products to improve its products continually. In <br /> Size <br /> PipeeSize <br /> (inchest 2" 3" - 4" accordance with that policy, the.right is reserved-to make changes in specifications, <br /> Ft. 75 105 140 descriptions and illustrative material contained in this bulletin as conditions warrant. <br /> The information contained herein is general in nature and is not intended to express <br /> any warranty of any type whatsoever nor shall any be implied. <br /> 'bCopyright 1992 Smith Fiberglass Products Inc. . <br /> It and''trademarks of Smith Fiberglass Products Inc. /IT <br /> PRINTED IN U.S.A. i <br /> 15M993 <br /> SFAM FIBERGLASS P&RODUICTS INL <br /> A SUBSIDIARY OF A. 0. SMITH CORPORATION <br /> 2700 West 65th Street® Little Rock,Arkansas 72209-8592 *Telephone(501)568-4010.TWX(9 10)722-7377 ® FAX(501)568-4465 <br />