COMPLIANCE INFO_1995-2006 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed RED WREADO 11A Piping ummmol '` • r SCOPE PIPE - Pipe shall be manufactured by Smith Fibercast by a filament winding process using a thermosetting epoxy resin to impregnate strands of continuous glass filaments which are wound around a mandrel at a prescribed helix angle and under controlled tension. All pipe will be supplied with matching tapered T.A.B TM (Threaded and Bonded) coupling and spigot ends or T.A.B. spigot x spigot ends. CONSTRUCTION 2"-4" PIPE - RED THREAD IIA pipe shall have continuous glass fibers filament wound at a 35%` helix angle in a matrix of epoxy resin. Pipe shall be in compliance with ASTM D2310 and classified by its designation code. Pipe shall meet all dimensional and performance requirements, mechanical properties, and shall be classified with the following designation codes: Size Designation Code at 73.4° F 2"-3" RTRP-11 AE 4" RTRP-11AF ITEMS ' 2"-4" PIPE - Glass fiber reinforced filament wound pipe with matching tapered T.A.B. (Threaded and Bonded) coupling and spigot ends. Pipe to be factory prooftested at the following pressures: 2" - 375 psig 3" - 300 prig 4" - 265 psig 2"=4" FITTINGS - Compression molded fittings shall be manufactured using an epoxy molding compound. The molding compound shall be reinforced with a minimum of 45% chopped glass fiber. In-line fittings are filament wound. ADHESIVES - Adhesive and curing agents shall be either UL Listed DS -8000 or DS -7000 series adhesive. Consult Smith Fibercast's installation manual No. B2160 for recommended heat curing techniques. JOINING TECHNIQUES 2"-4" PIPE and FITTINGS - Pipe and fittings shall be joined with DS -8000 or DS -7000 series adhesive using matching tapered bell/coupling and spigot. Material to be installed in accordance with Smith Fibercast's installation manual No. B2160. TESTING 2"-4" PRIMARY PIPE SYSTEMS - Primary pipe systems should be tested prior to use to assure soundness of all joints and connections. Consult Smith Fibercast's _} installation manual No. B2160. • • •ona 111111111 Ira• • SCOPE PIPE - Pipe shall be manufactured by Smith Fibercast by a filament winding process using a thermosetting epoxy resin to impregnate strands of continuous glass filaments which are wound around a mandrel at a prescribed helix angle and under controlled tension. CONSTRUCTION 3"-4" PIPE - RED THREAD IIA pipe shall have continuous glass fibers filament wound at a 35%* helix angle in a matrix of epoxy resin. Pipe shall be in compliance with ASTM D2310 and classified by its designation code. Pipe shall meet all performance requirements and mechanical properties, and shall be classified with the following designation codes: Size Designation Code at 73.4 3" RTRP-11 AE 4" RTRP-11 AF ITEMS 3"-4" PIPE - Glass fiber reinforced filament wound pipe with Plain end by Plain end. Pipe to be factory prooftested at the following pressures: 3" - 300 psig (minimum) 4" - 265 prig (minimum) 3"-4" FITTINGS - Compression molded two-piece fittings shall be manufactured using a vinyl ester molding compound. The molding compound shall be reinforced with a minimum of 60% chopped glass fiber. ADHESIVES - Adhesive and curing agents shall be either UL Listed DS -8000 or DS -7000 series adhesive. Consult Smith Fibercast's installation manual No. B2160 for recommended heat curing techniques. JOINING TECHNIQUES 3"-4" PIPE and FITTINGS - Pipe shall be joined with either DS -8000 or DS -7000 series adhesive. Fittings shall be joined with either DS -7000 or DS -8000 series adhesives and filler. Material to be installed in accordance with Smith Fibercast's installation manual No. B2160. TESTING 3"-4" SECONDARY CONTAINMENT PIPE SYSTEMS - Secondary containment pipe systems should be tested prior to use to assure soundness of all joints and connections. Consult Smith Fibercast's installation manual No. B2160.