Laserfiche WebLink
TANK 0 <br /># # # <br />CAPACITY <br />Z oCt-3 p v' C! I 0 (� <br />oYS7cM PRINTSET <br />INFORMATION <br />�fZ 0s- c- • T-rL ) <br />1. <br />ST F 2P <br />Four complete sets of plans (To include specification sheets and/or equipment brochures if not on file). <br />2. <br />MODEL <br />Plans drawn to scale in non -erasable print. <br />3. <br />Plot plan to show location and number of tanks. <br />:. <br />Tank cross-sectional diagram included on prints submitted. <br />CORROSION PROTECTION <br />Detail of tank, piping system, excavation and cover. <br />U.L. LISTED <br />C, -S r Y <br />5. <br />1/11, <br />Tank(s) and piping approved by a nationally recognized independent testing organization. [Title 23, Subchapter 16, <br />L/ <br />Article 3, Sec. 2631 (r) & 26351 <br />7. <br />Verification of product compatibility with the tank(s), piping, monitoring <br />device(s), epoxy or silicone glues, etc. [Section 2635 (b) (2)] <br />3. <br />Manufacturer's written installation instructions for tank(s), piping, monitoring devices, etc. [Section 2635 (b) (5)] <br />�. <br />Tightness Test (NFPA 30) is required on both primary (10) and secondary (20) containment systems before covering. <br />[Section 2635 (b) (6) & (7)] <br />/ <br />10. <br />✓ <br />Double walled tanks using pressure or vacuum testing to monitor the annular space. [Section 2635 (b) (7)] <br />•I1. <br />NFPA 329 "Precision Test" required upon completion of installation with tank in operating condition. Test results to <br />be submitted directly to PHS/EHD from the testing company or owner of facility. [Health & Safety Code, Division 20, <br />Chapter 6.7, Section 25291 (g)] <br />'2. <br />TANK rnMPnCTTTnY <br />TANK 0 <br /># # # <br />CAPACITY <br />Z oCt-3 p v' C! I 0 (� <br />MANUFACTURER <br />�fZ 0s- c- • T-rL ) <br />COMPOSITION <br />ST F 2P <br />MODEL <br />PRODUCT <br />I\ <br />CORROSION PROTECTION <br />U.L. LISTED <br />C, -S r Y <br />COMPATIBILITY WITH 100% <br />METHANOL <br />L/ <br />3. TANK(s) TO BE INSTALLED <br />,1 A. Steel -clad with fiberglass reinforced plastic. <br />_ 9ii ki. Holiday test required immediately before "setting" tank(s) (35,000 - 40,000 volts). [Section 2635 (b) (4)] <br />` t(prC. Fiberglass [Sections 2635 (3) and 2631 (p)] <br />(1) Striker plate dimensions and materials. <br />(2) Striker plate under all accessible openings. <br />(3) Installation instructions require an air test and soap bubble test prior to installation. <br />4W. Non -clad steel tank [Section 2635 (b)] <br />(1) Cathodic protection provided for entire tank, piping and components (nuts, bolts, washers, <br />etc.). <br />(2) Approved by a corrosion engineer or N.A.C.E. technician. <br />(3) Document stating inspection method and frequency (minimum semi-annual inspection requirement). <br />4 <br />