COMPLIANCE INFO_2002-2005 - Laserfiche WebLink

Home Browse Search

10/18/2005 TUE 10:28 FAX 015/038 ULIULC Listed Red Thread®if A P12ing 5 stem GENERAL SPECIFICATIONS Primary Pieing Secondary Containment Piping SCOPE SCOPE PIPE—Pipe shall be manufactured by Smith Fibercast by a PIPE—Pipe shall be manufactured by Smith Fibereast by a filament winding process using a thermosetting epoxy resin filament winding process using a thermosetting epoxy resin to impregnate strands of continuous glass filaments which to impregnate strands of continuous glass filaments which are wound around a mandrel at a prescribed helix angle and are wound around a mandrel at a prescribed helix angle and under controlled tension. All pipe will be supplied with under controlled tension. matching tapered TA.B_T°' (Threaded and Bonded)coupling and spigot ends or TA_B_spigot x spigot ends. CONSTRUCTION CONSTRUCTION 3"-6"PIPE—RED THREAD iiA pipe shall have continuous glass fibers filament wound at a 540 wind angle In a matrix 2114"PIPE—RED THREAD IIA pipe shall have continuous of epoxy resin_ Pipe shall be in compliance with ASTM glass fibers filament wound at a 64°wind angle in a matrix D2310 and dassi led by Is designation code. Pipe shall of epoxy resin. Pipe shall be in compliance with ASTM meet all performance requirements and mechanical D2310 and classified by Its designation code. Pipe shall properties,and shall be classified with the following meet all dlmenslonal and performance requirements, designation codes: mechanical properties,and shall be classified with the Size Designation Code at 73.4°F following designation codes: 3" RTRP•11AF Size Designation Code at 73.4"F 4"-6" RTRI�-�tall 2"-3" RTRP-11 AF 4" RTRP-11AH ITEMS ITEMS 7 E 3"-6"PiPE—Gass Fiber reinforced filament wound pipe with Plain end by Plain end or T.A.B.spigot by spigot ends. Pipe 2"4"PIPE—Glass fiber reinforced Filament wound pipe with to be factory proofiested at the following pressures: matching tapered TA.B.(Threaded and Bonded)coupling 3"-300 prig(minimum) and spigot ends or T.A.B.spigot by spigot ends, Pipe to be 4"-265 prig(minimum) factory prooftested at the following pressures: 6`-265 psis(minimum) 2"-375 psig 3"-6n FITTINGS—compression molded two-piece fittings 3"-300 psig 4"-265 psig shall be manufactured using a virryi ester mottling compound. The molding compound shall be reinforced with 2"4"FITTINGS—Compression molded fittings shall be a minimum of 60%chopped glass fiber. manufactured using an epoxy molding compound. The molding compound shall be reinforced with a minimum of ADHESIVES—Adhesive and curing agents shall be either 45%chopped glass fiber. In-line fittings are filament wound. UL Listed 6M0 or 7000 series adhesive. Consult Smith ADHESIVES—Adhesive and curing agents shall be ether Fibercast's installation manual No.02160 for recommended g 9 heat curing techniques. UL Listed 8000 or 7000 series adhesive. Consult Smith Ffbercast's installation manual No.82160 For JOINING TECHNIQUES recommended heat curing techniques. 30-6n PIPE and FITTINGS—Pipe shalt be joined wish either JOINING TECHNIQUES 8000 or 7000 series adhesive. Fittings shall be joined with either 7000 or 8000 series adhesives and filter. Material to 2"-4"PIPE and FITTINGS—Pipe and fittings shall be joined be installed in accordance with Smith Fibercast's Installation with 8000 or 7000 series adhesive using matching tapered manual No.82160. bellicoupling and spigot. Material to be installed in TESTING accordance with-Smith Fibercast's installation manual No_ p 82160. 3"-ti"SECONDARY CONTAINMENT PiPE SYSTEMS— Secondary containment pipe systems should be tested prior TESTING to use to assure soundness of all joints and connections. 2"4"PRIMARY PIPE SYSTEMS—Primary pipe systems Consult Smith Fibercast's installation manual No.B2160, should be tested prior to use to assure soundness of all joints and connections. Consult Smith Fibercast's installation manual No.132160. Nak.s'�econaarycontainmPntpipe ano rnttings are not uuuLC Usied 10