Laserfiche WebLink
0 0 <br />Primary Piping System Installation <br />TABLE 6. 7000 & 8000 Adhesive Kit Data <br />Kit ID Number <br />(Excludes Solvent) <br />Label <br />ColorV) <br />2" Quantity <br />Mixed Adhesive <br />Approx. No. of Bonds Per KJ(2) <br />2" 3" 4" <br />(50 mm) (75 mm) (100 mm) <br />Working <br />Life(2) at <br />75°F (23.9°C) <br />Minutes <br />7014 <br />Red <br />5.4 oz. (193 g) <br />25 <br />18 <br />10 <br />25 <br />7024 (WAn Pack) <br />Black <br />2.0 oz. ea. (71 g ea.) <br />9 <br />6 <br />4 <br />25 <br />7069(2) <br />Blue <br />7.8 oz. (282 g) <br />- <br />- <br />- <br />25 <br />8014 <br />Green <br />5.5 oz. (181 g) <br />21 <br />15 <br />8 <br />15 <br />8024 (Twin Pack) <br />Yellow <br />2.3 oz. ea. (77 g ea.) <br />18 <br />12 <br />8 <br />15 <br />L 8055 (Bag Kit) <br />No Color <br />1.6 oz. (45 g) <br />3 <br />2 <br />1 <br />15 <br />1 80690) <br />Orange <br />8.0 oz. (264 g) <br />- <br />(These adhesives are for RED THREAD IIA piping systems conveying petroleum products including leaded and unleaded gasoline, <br />diesel, 100% ethanol or methanol, all alcohol -gasoline mixtures and biodiesel fuels.) <br />Watch the labeled adhesive color to the hardener color before mixing. <br />OWhen adhesive is properly mixed, it has a limited "working life" during which <br />joints maybe bonded. Use of the adhesive beyond the working life is prohibited. <br />ORecommencled for secondary containment installations due to size of kit. <br />ADHESIVE WORKING LIFE <br />Working life or pot life is the time it takes for the adhesive <br />to harden in the mixing can. This time is measured from the <br />time the adhesive and hardener are first mixed. Working <br />life is shorter at temperatures above 75°F (21°C) and <br />becomes longer as the temperature drops below75°F (211C). <br />Working life is affected by the quantity of mixed adhesive <br />as well as by temperature. Use the following methods to <br />increase the working life of adhesives: <br />Warm Weather: <br />• Occasionally stir the adhesive mixture during <br />application. <br />• Use small Ice chests or other containers with fteezer <br />packs to keep adhesive cool. <br />Cool Weather: <br />• Store adhesive kits inside. <br />• Prewarm tab 700-SOPF (21.10-26.M) before <br />use. <br />ACAUTION: If adhesive becomes warm and <br />!tarts to harden in the container, discard <br />immediately. DO NOT USE THIS ADHESIVE TO <br />BOND A JOINT! <br />When adhesive is allowed to harden in the metal <br />container, the container may reach approximately 400°F <br />(2050C). Do not handle hot containers without heavy gloves. <br />This exothermic reaction will generate a dense, foul-smelling <br />smoke. Therefore, place the container outdoors in an open <br />area until it cools. Avoid inhaling smoke. <br />7 <br />ADHESIVE DISPOSAL: Once the adhesive and catalyst have <br />been mixed and reacted, nothing can be extracted, and it is <br />classified as non -hazardous material. Dispose of in a normal <br />manner as other solid waste. Excess adhesive and catalyst can <br />be mixed, allowed to react, and disposed of as above. If extra <br />cans of adhesive or tubes of catalyst have accumulated with- <br />out the other component to mix and react, contact your FGS <br />regional manager. Catalyst tubes, when empty are not subject <br />to EPA regulation and can be disposed of in a normal manner. <br />These guidelines are based on federal regulations. State and <br />local regulations and ordinances should be reviewed. <br />