COMPLIANCE INFO_1986-1996 - Laserfiche WebLink

Home Browse Search

C C 27. Sensor Calibration / lb 30. HYDROSTATIC PRESSURE CONTROL 31. VOLUME MEASUREMENTS IV) RECORD TO 001 GAL 34. TEMPERATURE COMPENSATION USE FACTOR lal 38, NET VOLUME CHANGING EACH READING 39, ACCUMULATED CHANGE LOG OF TEST PROCEDURES ' DATE —" TtAdE—'- 124 ht I Record details of settingu P and running test (Use full iengll, of line dneeded -t 29. Heading No V Standpipe Levet m Inches 32. Product m GraiWaie 33. Product Replace) 1.1 35. The+mat Sensor Reading 36. gi;+ri e V Higher lower • Id 37 Computation (d . (al Expansion • Contraction - Temperature Ad,usun-1 __. ._._... _ Volume Minus Expansion (•) or Contraction f-) a33(VI — WIT) At Low level comput Change pe r Hour Change petenal INIPA Beginning 01 Reading Level to which Res,oied 8elo(e Reading Aller Reading Product Recovered I.1 ARRIVED AT TESD LOCATION —REMVED MIMI' ILL UP, AMPTERS, IND SPLAAH TUBES FROM FILL PIPES. In CM SET UP EQUIPMENT # 1 START CIRCULATION # 2 # FA=R P (.l- —7 ) #Z # FACMR A 1St TSIERMO READING # START HIGH LEVEL TEST 42 ' I 1st HIGH LEVEL READING # 1 ee ie ee ee is # 1 I HIGH LEVEL READINGS CONT. # 2 -1A 4Q ��y n ee n ee a 2` INOWI + � I I ei ee n ie n # 3 �• ✓ .�✓ of ei of It if # 4 t ILM Is is to is # tr C J e� / ( µ +15 1 Q 4T.(/lam � ( 11 ee n ie ee # 5� 'V.1lJ n ie ee ee # 6 ® }'VC.�e✓ wJ�LJ� �� +'l J�"1 ei ei ie a ie # 6Z P -T Tank Test Data Chart Additional Info 1. Net Volume Change at Conclusion of Precision Test ...--- gph Signature of Tester: Date: 2. Statement: ❑ Tank and product handling system has been tested tight according to the Precision Test Criteria as established by regulatory agency. This is not intended to indicate permission of a leak. OR ❑ Tank and product handling system has lailod the tank tightness test according to the Precision Test Criteria as established by regulatory agency. OR ❑ Tosl invalid duo to unvironniuntnl ur nwchanicul IR<;lors boyonrl control of 1110 lusting uqu,pniunl. It is the responsibility of the owner and/or operator of this system to immediately advise state and local authorities of any implied hazard and the possibility of any reportable pollution to the environment as a result of the indicated failure of this system. The manufacturer of this test method does not assume any responsibility or liability for any loss of product to the onvironmonl. Tank Owner/Operator Dain MIMI' In MIMMI ' I I INOWI � I I M1 P -T Tank Test Data Chart Additional Info 1. Net Volume Change at Conclusion of Precision Test ...--- gph Signature of Tester: Date: 2. Statement: ❑ Tank and product handling system has been tested tight according to the Precision Test Criteria as established by regulatory agency. This is not intended to indicate permission of a leak. OR ❑ Tank and product handling system has lailod the tank tightness test according to the Precision Test Criteria as established by regulatory agency. OR ❑ Tosl invalid duo to unvironniuntnl ur nwchanicul IR<;lors boyonrl control of 1110 lusting uqu,pniunl. It is the responsibility of the owner and/or operator of this system to immediately advise state and local authorities of any implied hazard and the possibility of any reportable pollution to the environment as a result of the indicated failure of this system. The manufacturer of this test method does not assume any responsibility or liability for any loss of product to the onvironmonl. Tank Owner/Operator Dain