COMPLIANCE INFO_2000-2005 - Laserfiche WebLink

Home Browse Search

r Spill Containment— OPW EVR Thread-on or OPW/POMECO EVR Multi-Port Spill Containers are certified for installation on the OPW Phase 1 PVR system.All fill ports in these spill containers _ feature enhanced 1 DK-2100-EVR vapor tight drain valves that exceed the EVR requirements for a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O.The vapor return spill containers feature a permanent plug installed in the drain ports, as per EVR requirements. Overfill Prevention —The OPW 61 SO-40OC-EVR Series Overfill Prevention Valves are certified for installation on the OPW Phase 1 EVR system.The vapor tight EVR 61 SO's are designed to provide positive shut-off of product delivery, before an overfill condition occurs, per EPA requirements, q without intervention from the transport driver.The valve features a sealed float pivot and a threaded lower tube connection,and exceeds the EVR requirement for a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O.The 61 SO-EVR Series Valve is installed in the base of the OPW EVR Spill Container with the patent pending 611SK lack Screw device.This config uration allows . liquid in the spill container to be drained directly into the drop tube,thereby isolating the drain valve from the tank ullage,eliminating a notorious leak point in previous systems. Tank Bottom Protector-The OPW/POMECO 6111-1400 Tank Bottom Protector is EVR certified for installation at the bottom of the overfill prevention valve drop tube to help prevent the damage from erosion or tank gauging sticks. underground storage tank from sustaining _ K . a Ball Float and 233 Extractor—The OPW 53VML Ball Float, 233 Extractor and 61T Fill Drop Tube configuration can be installed as an alternative to the 6150 Overfill application.The installation of the Ball Float/Drop Tube system is identical to the 61 SO Overfill Valve on the OPW Phase 1 Vapor Recovery System. Rotatable Swivel Adaptors (Fill and Vapor) —OPW EVR Rotatable Swivel Adaptors are certified for installation on the fill and vapor ports on the OPW Phase 1 EVR system. OPW Swivel Adaptors P 360 degrees of rotation of any product or vapor recovery elbow to prevent the adaptors from loosening on the spill container risers.OPW Svulvel Adaptors exceed the EVR requirement to maintain a minimum 360-degree rotation with an average static torque not to exceed 108 inch- pounds (9 foot-pounds).The enhanced poppet system on the OPW 61VSA-EVR vapor swivel adaptor provides a vapor tight seal when closed, per EVR requirements. Adaptor Tool —An OPW 61 SA TOOL is required to ensure proper installation of OPW Rotatable Swivel Adaptors, spill containers and threaded riser adaptors, per EVR requirements.The i" 61S ATOOL includes provisions for the use of a torque wrench to facilitate accurate installation And testing. Dust Caps(Fill&Vapor)—OPW EVR Dust Caps are certified for installation on OPW EVR Certified Rotatable Adaptors. OPW EVR Certified Dust Caps feature enhanced ribbed seals and increased sealing forces to provide a bubble-tight < seal, per EVR requirements.Available in Duratuff or low-profile metal models. Threaded Riser Adaptor(Face Seal Adaptor)—An OPW FSA-400 Threaded Riser Face Seal Adaptor is required to provide a flat,true sealing surface on threaded pipes where a gasket seal exists per EVR requirements.The FSA-400 is installed on the fill pipe riser below the spall container to provide a true sealing surface for the drop tube flange on the 61 SO-4000-EVR Overfill Prevention Valves.The FSA-400 is also required on tank gauging risers,though is optional on vapor risers and rotatable adaptors. Pressure Vacuum Vent—The OPW 623V Pressure Vacuum Vent is certified for installation on the OPW Phase 1 EVR system.The 623V's are installed on the top of the vent pipes for underground fuel storage tanks.The vent cap and internal wire screen are designed to protect the tank et nn lines against intrusion and blockage from water, debris or insects.A normally closed pope the valve opens at a predetermined pressure or vacuum setting to allow the tank to vent The 623V exceeds the EVR requirement of a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O.