COMPLIANCE INFO_1992-2005 - Laserfiche WebLink

Home Browse Search

r „ll� ! ! 1 ! ! ! , TERMINATION TEE St1° EL80W 45° ELBOW SLEEVE COUPLING CONCENTRIC REDUCER F. A Sizes available for Termination Concentric Reducers, with and without tap: 3"x 2", 4"x 3", *6"x 4". SRES SIZES AVAILABLE Sailed sloe outlet Thread®d swe alai NPT flannel ThreadsM 3"x2" 3"x1" 4" x 2" 3" x 1 'A" 4" x 3" 3” x 1 th" 7 4"x1„ 3 4" x 11/4" 2tk' 4" x 1 Y4" *NOTE: 6" secondary containment fittings are not UL/ULC Listed. 4.. PliESSU!i RATINGS `kt ra�i"Se' .,^x *P H�Y+i Z �t f" „ •#'fit f Blind Rediust'l ' _ at 150° F 9,300'psi 64.12 MPa 1 �,, F1 3'f 31, 6 7 14 3 21/2 2tk' 4" 71h 6 14 3 3 2t/2 611* L8 9 16 4 4 3 *NOTE: 6" secondary containment fittings are not UL/ULC Listed. 4.. PliESSU!i RATINGS `kt ra�i"Se' .,^x *P H�Y+i Z �t f" „ •#'fit f Blind Rediust'l ' _ at 150° F 9,300'psi 64.12 MPa 1 �,, F1 3'f 90 4" so 6"* ro1 SADDLES Bending Properties of RED THREAD 11 Pipe N• � k% � H3N� `t�' !fid) �F �N '� ��! .,^x *P H�Y+i Z �t aril. dH! r ..Y4 Blind Rediust'l ' _ at 150° F 9,300'psi 64.12 MPa Compressive Strength — Axial at 75° F 22,700 psi 50 ft. 2„ 15.7 m 3„ 80 ft. ASTM D-2105 24.4 m 4„ 100 tL 30.5 m N• � k% � H3N� `t�' !fid) �F �N '� ��! .,^x *P H�Y+i Z �t aril. dH! r ..Y4 Tensile Strength -- Axial at 75° F 11,900 psi 82,05 MPa 9 ASTM D-2105 _ at 150° F 9,300'psi 64.12 MPa Compressive Strength — Axial at 75° F 22,700 psi 156.51 MPa ASTM 6-695 Modulus of ElasticityIn Tension at 75° F 1.92 x 100 psi 1.32 x 11)4 MPa ASTM D-2105 _ at 150° F 1.70 x 100 psi 1.17 x 1(14 MPa Ultimate Hoop Tensile Strength at Burst Average at 75° F 44,000 psi 303.37 MPa ASTM D-1599 Long Term Hoop Strength at 750 F 9,140 psi 63.02 MPa ASTM D-2992 Cyclic Pressure (150 x 106 cycles) at 150° F 8,020 psi 55.30 MPa Procedure A Thermal Expansion Axial 2" 3" 4" pipe 1.09 x 10-6 in./In./°F 1.96 x 10'' mm/mni/'C AOSI-TM16-3 Thermal Conductivity 2" 3" 4" pipe 2.9 STU/(fL2)(hr.)(°F/in.) 0.42 W/(m)(°K) AOSI-TM16-15 S ecilic Gravity 1.85 1.85 ASTM D-792 Flow Factor Hazen -Williams Coefficient 150 151) AOSI (1) A 3" x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated 44) Dept net available at time of (6) Pipe Is manufactured In compliance not UL/ULC Listed is available for must be made with a to avoid stress concentration which prin8ng. with ASTM D-2696. Refer to general use with the 4"x 3" termination flexible connector, would result in premature Pipe failure specification shoat In catalog for the concentric reducer. under pressure condillotis.r (a) Tests run on pipe rampiea. 0-2998 designation code.