Laserfiche WebLink
86 SERIES <br /> SPECIFICATIONS <br /> MULTISTAGE CENTRIFUGAL BLOWER <br /> Number of Stages...............1 through 9 <br /> - ., -..-••-•.•.... <:_._.�:-•� :• Inlet Connection..................8"(203.2 mm)flange,ASA 125#drilling <br /> • •• •-::. ., Outlet Connection................B'(203.2 mm)flange,ASA 1251 drilling <br /> Operation Speed..................3550 RPM(60 Hz),2960 RPM(50 Hz) <br /> rte'` ....;}.� sing Pressure(max.).......25 PSIG(1. 5 kg/cm') <br /> Ca es 7 <br /> :. tea::::::.=u•.. f <br /> `:�• �• ;; Seats(ail)...........................Carbon ring,two each end <br /> Seals as Stuffing box type(special seals available <br /> '`-H Bearings:.............................Ball,10-year minimum life perAFBMA L70 standard <br /> t' Lubrication..........................Grease(standard)or Oil <br /> - Impeller Diameter................24,00 in(609.6 mm) <br /> Impeller Tip Speed..............372 fVs(113 m/s)®3550 RPM <br /> ? First Critical Speed..............4323 RPM(9-stage) <br /> - Drive Type...........................Direct coupled or Belt driven, <br /> Inlet driven(standard)or Outlet driven <br /> Shaft End............................1.875 in(47.63 mm)diameter at coupling <br /> 86 SERIES BLOWER Vibration Tolerence..............25 in/sec(6.4 mm/sec)ISO overall specification, <br /> 14,7 PSIA(101.4 kPa),68°F(20°C),36%RH,3550 RPM 1.25 mils(0.03 mm)peak to peak <br /> kPa PSIG DHF kid Rotor Balance......................Individual impellers statically balanced and i <br /> 120 18 360 zea complete rotating assembly dynamically balanced <br /> 16 ' ' 320 240 <br /> 100 -— -.__..__.,_._,_.. <br /> 14 �... ... leo 220 ac <br /> _.f...._._..„ .. _. ;- ' ' -i 200 w <br /> q 80 12 ' 240 100 <br /> 0° 10 =0i41-- <br /> 8 160 120 a <br /> p i <br /> h40 ° s_ 120 ao0 Iz a Casing..................... .......Cast iron ASTM A48 grade 30 <br /> —^ 4 <br /> " 20 z -- - -ao o y' Bearing Caps&Housings...Cast iron ASTM A48 grade 30 <br /> i <br /> 0 _.: _....__.�_y...,... 020 ry ...................... Cast aluminum ANSI AA319 <br /> Olr <br /> 1500 2000 zsoo 3000 3500 4000 c>sn+ Shaft .......Carbon steel AISI 4140(stainless steel available) <br /> ' I Reservoir <br /> 3000 ssoo aIN ET;FLO5600 RTE5°° 6000 6500 7000.'/h, Impellers.............................Cast aluminum ANSI AA319 or Fabricated <br /> aluminum ANSI AA6061 with Cast Al AA356 Hub <br /> 86 SERIES EXHAUSTER Seals(air)............................Isostatically molded,high density,fine grain I <br /> 29.92 InHg(760 mmHg),68°F(20°C),36%RH,3550 RPM electro-graphite <br /> mmHg irft BHP kw Seals(gas)..........................Cast aluminum ANSI AA319 stuffing box with <br /> 400 1e � no braided packing i <br /> 850 14 175 14 <br /> 0 Interstage Baffle Rings........Stainless steel ASTM A240 304 <br /> --,-. 1stow <br /> 300 t2 50 Tie Rods...............................75 in(19.1 mm)diameter,high strength steel <br /> a ASTM A193-B7 <br /> 250 10 125 1°°qp, <br /> 200 a 100 8D Blower Base........................Welded structural steel <br /> a <br /> 150 6 75 8° Motor Pedestal....................Welded steel plate <br /> 100 4 50 40 Joint Sealing Compound.....RTV silicone <br /> 50 2 25 20 Base isolation Pads.............Neoprene rubber <br /> 1500 zo0o 2500 3000 3500 4000 CFM Finish..................................Two-part epoxy ASA61 gray <br /> 3000 3500 4000 4500 5000 5500 6000 6500 7000 ml/hr <br /> INLET FLOW RATE <br /> Note: Specifications subject to change without notice. <br /> 02005 Houston Service Industries,Inc. www.hsiblowers.com <br /> I <br /> 1 <br /> I <br />