ARCHIVED REPORTS_XR0006616 - Laserfiche WebLink

Home Browse Search

leve} All screens and casings used will be in a contaminant-free condition when placed in the ground No thread lubrication shall be used, other than teflon tape or distilled water, during the connection of individual lengths of screened and solid well casing Screen shall not be placed in a borehole that creates hydraulic interconnection of two or more distinctly separate aquifer units. Screen slot size will be chosen to be compatible with the encountered aquifer materials. The screen slot size will be chosen to retain a high percentage of the filter pack or natural formation. The remainder of the well casing, above the screened interval, shall be of solid riser casing. A sand pack shall be placed in the remammg anular space surrounding the well casing to a minimum of 1 foot above the screened interval. Sand pack shall not be placed such that it interconnects two or more distinctly separate aquifer units. Sand pack shall be chosen to be compatible with both the aquifer materials and the screen slot size. Sand pack shall consist of clean, washed, kiln dried silica sand. A miumurn 1-foot thick bentonite pellet or bentonite slurry seal shall be placed above the sand pack. All bentomte shall be hydrated by either formation water or steam-distilled water The remaining annular space above the bentonite seal shall be grouted with a neat cement or bentonite-neat cement mixture and shall be placed from the top of the bentonite pellet seal to within 6 inches of the top of the well If used, the bentorute content of the mixture shall not exceed 5 percent by weight Sand pack, bentonite, and cement seal levels will be confirmed during construction by measuring the remaining anular space with a calibrated weighted tape If shallow water table conditions prevail, the screen interval will be placed such that the screen height above the static water level is reduced and a maximum possible surface seal can be achieved A held boring log and well construction diagram (Plate A-1) shall be prepared by a representative of HETI for each well completed Monitoring and extraction wells shall be constructed with CIass-A cement/bentonite grout or bentonite pellets tremied into position as a base for the well casing if necessary The well casing will be set within the aquifer according to the proposed function of the well and the chemistry of the potential contaminants In the event a monitoring well is required to be installed in an aquifer unit underlying an i existing, shallower aquifer, the well will be completed in the lower aquifer such that only water from the lower aquifer is drawn into the well The upper aquifer will be sealed by installing a steel conductor casing which extends to the base of the shallow aquifer The steel casing will be trenved into position with an annular neat cement or cement-bentonite grout seal placed between the outside wall of the casing and the wall of the borehole. The cement grout will be allowed a ininunnun of 72 hours to set prior to advancing the boring beyond the sealed conductor casing and into the next aquifer. After 72 hours,the boring will be advanced below the seal and completed as a well as described above but within the steel conductor casing The tops of all well casings will be sealed and placed in a vandal resistant, traffic rated box to prevent entry of surface contamination,unauthorized entry and tampering Monitoring wells will be surveyed to obtain north-end casing elevations to the nearest± 0 01 foot Water level measurements will be recorded with an interface probe to the nearest±0 01 foot and referenced to either a project datum or mean sea level (MSL). A project site datum is typically chosen such that it will remain in the event the project site undergoes a physical change as a result of construction or other cultural disturbance Where required, the wells will be surveyed by a licensed land surveyor relative to the nearest bench mark and relative to mean sea level Typically, the establishment of a known, on-site reference by a licensed survey, is enough to allow for the rens ping well top elevations to be determined using a survey level and prod. Unless directed'otherwise by local regulatory agencies, the well top elevations will be I established in,this'manner I , 3 i, I I I ❑ll I I If�ll I ilhl' rl ' !1,II'lll ill I IV I Ili I IIli,�l I SII!it 'I', II I it � Illli 11 ''�I I II ! li ii I I 'I III I�ill' II� I! fi it IIII i illl'I I ' Ili I i I„ I! 1 i I