|
SECTION 09260 - GYPSUM WALLBOARD ASSEMBLIES SECTION 09900 - PAINTING SECTION 10155 - TOILET COMPARTMENTS
<br /> 1. For assemblies with fire resistance ratings, provide materials and construction identical to those tested in assembly PARTS 1 - GENERAL 3.03 PREPARATION: 1. Subject to compliance with requirements, provide products by one of the following:
<br /> indicated by ASTM E 119 . A. Perform preparation and cleaning procedures in strict accordance with coating manufacturer's instructions for each A. Accurate Partitions Corporation
<br /> A]
<br /> 2. For assemblies with STC ratings, provide materials and construction identical to those tested in assembly indicated by 1.01 SUMMARY: substrate condition. B. Bobrick Washroom Equipment, Inc.
<br /> ASTM E 90 and ASTM E 413. C. Crane Plumbing; Sanymetal.
<br /> A. Section Includes: Painting and finishing of all interior and exterior items and surfaces, unless otherwise indicated or B. Concrete and Masonry: Surfaces shall be dry, clean, and free of dirt, efflorescence, encrustation, and other foreign
<br /> 3. STEEL FRAMING: ASTM C 754, Steel Sheet Components: ASTM C 645, ASTM A 653 G60 hot dip galvanized zinc coating. listed under exclusions below: matter. Glazed surfaces on concrete shall be roughened or etched to uniform texture. D. Global Steel Products Corp. Architecture / Development
<br /> Minimum Base Metal Thickness: 0.0312 inch unless noted otherwise. E. Metpar Corp.
<br /> 1. Paint all exposed surfaces, except as otherwise indicated, whether or not colors are designated. C. Ferrous Metal: Clean oil, grease, and foreign matter with solvent. Surface shall be primed within 3 hours after
<br /> 4. TIE WIRE: ASTM A 641/A 641M, Class 1 zinc coating, soft temper, 0.0625 inch diameter wire, or double strand of Include field painting of exposed exterior and interior plumbing, mechanical and electrical work, except preparation. F. Weis/Robart Partitions, Inc. 14901 Quorum Drive
<br /> 0.0475 inch diameter wire. 2. STEEL SHEETS WITH COLOR COATED FINISH: Mill hos hatized corrosion resistant steel see ; stretcher leveled flatness
<br /> as indicated below. D. Sand and scrape metal to remove loose primer and rust. P P � � Suite 300
<br /> 5. WIRE HANGERS: ASTM A 641/A 641M, Class 1 zinc coating, soft temper, 0.162 inch diameter. 2. Paint exterior stucco where indicated on Drawings. E. Non-Ferrous Metal: Chemically or solvent clean and then treat with on etching-type solution if recommended by the ASTM A 591/A 591M, Class C, or ASTM A 653/A 653M; with manufacturer's standard baked finish. Color: As selected Dallas Texas 75254
<br /> 6. CARRYING CHANNELS: Cold rolled, commercial steel sheet with a base metal thickness of 0.0538 inch a minimum 1/2 B. Work Included: finish manufacturer. Cleaned and retreated Non-Ferrous Metal shall be rimed the same da that cleaninghas been from manufacturer's full range
<br /> inch wide flange, and in depth indicated. 1. The intent and requirements of this Section is that all work, items and surfaces which are normal) painted and P y Fa ((97 239-584
<br /> 9 P q Y P performed. 3. Core Material for Metal Faced Units: Sound deadening honeycomb of resin impregnated kraft paper in thickness required Fax: (972)239-5054
<br /> 7. COLD ROLLED CHANNELS: 0.0538 inch bare steel thickness, with minimum 1/2 inch wide flange, 3/4 inch deep. finished in a building of this type and quality, shall be so included in this contract, whether or not said work, F. Wood Surfaces: Remove dust, grit and foreign matter. Sand surfaces and dust clean. Spot coat knots, pitch to provide finished thickness of 1 inch minimum for doors, panels, and screens and 1-1/4 inches minimum for
<br /> 8. Steel Studs and Runners: ASTM C 645, in depth indicated. item or surface is specifically called out and included in the schedules and notes on the drawings, or is, or is streaks, and sappy section with pigmented stain sealer when surfaces are to be painted. Fill nail holes, cracks and pilasters. ISSUE RECORD
<br /> 9. HAT SHAPED, RIGID FURRING CHANNELS: ASTM C 645, 7/8 inch deep. not, specifically mentioned in these specifications. other defects after priming and spot prime repairs when fully cured. 4. PILASTER SHOES AND SLEEVES (CAPS): Stainless steel, not less than 3 inches high. DATE DESCRIPTION
<br /> 10. RESILIENT FURRING CHANNELS: 1/2 inch deep members designed to reduce sound transmission, and asymmetrical with C. The following general categories of work and items that are included under other sections shall not be a part of this G. Remove hardware and accessories, machined surfaces, plates, lighting fixtures and similar items in place and 5. STIRRUP BRACKETS: Chrome plated, nonferrous, cast zinc alloy (zamac) or clear-anodized aluminum
<br /> single leg. section: not-to-be-finish painted, or provide surface-applied protection. Reinstall removed items upon completion of work in 6. CONTINUOUS BRACKETS: Clear anodized aluminum or Stainless steel. URBAN PROTOTYPE DESIGN
<br /> 11. GRID SUSPENSION SYSTEM FOR INTERIOR CEILINGS: ASTM C 645, direct hung system of interlocking main beams and 1. Shop prime painting of structural and miscellaneous iron or steel. each area. 7. TOILET COMPARTMENTS: Overhead braced and floor anchored 10-22-2018 ISSUED FOR PERMIT
<br /> cross furring members. 2. Shop prime painting of hollow metal work. H. Existing surfaces to be recoated shall be thoroughly cleaned and deglossed by sanding or other means prior to 8. URINAL SCREENS: Wall hung.
<br /> 12. DEEP LEG DEFLECTION TRACK: ASTM C 645 top runner with 2 inch deep flanges. 3. Shop finished items. painting. Patched and bare areas shall be spot primed with some primer as specified for new work. 9. DOORS: Unless otherwise indicated, 24 inch wide in swinging doors for standard toilet compartments and 36 inch wide
<br /> 13. FIRESTOP TRACK: Top runner manufactured to allow partition heads to expand and contract with movement of the D. The Room Finish Schedules indicated on the drawings indicates the location of interior room surfaces to be painted I. Thoroughly backpaint all surfaces of exterior and interior finish lumber and millwork, including doors and window out swinging doors with a minimum 32 inch wide clear opening for compartments indicated to be accessible to people
<br /> structure while maintaining continuity of fire resistane rated assembly indicated; in thickness not less than indicated or finished. The schedule indications are general and do not necessarily define the detail requirements. Include all frames, trim, cabinetwork, etc., which will be concealed after installation. Backpaint items to be painted or enameled with disabilities.
<br /> P g P P P
<br /> for studs and in width to accommodate depth of studs. detailed refinements and further instructions as may be given for the required complete finishing of all spaces and with the priming coat. Use a clear sealer for backpriming where transparent finish is required. 10. DOOR HARDWARE: Clear anodic aluminum or cast zinc alloy (zomac) or Stainless steel. Provide units that comply with
<br /> 14. FLAT STRAP AND BACKING PLATE: Steel sheet for blocking and bracing in length and width indicated. rooms. J. Bare and covered pipes, ducts, hangers, exposed steel and ironwork, and primed metal surfaces of equipment accessibilityrequirements of authorities having jurisdiction at compartments indicated to be accessible to people with
<br /> 15. GYPSUM WALLBOARD: ASTM C 36, Regular Type: In thickness indicated and with long edges tapered and featured E. Related Sections: installed under mechanical and electrical work shall be cleaned prior to priming. disabilities.
<br /> q g P P P
<br /> rounded or beveled), Type X: In thickness indicated and with Ion edges tapered and featured rounded or beveled Section 05 70 00 - Ornamental Metal K. Preparation of other surfaces shall be performed following specific recommendations of the coatings manufacturer. 11. Install units rigid, straight, level, and plumb, with not more than 1 2 inch between pilasters and panels and not more
<br /> ( ) YP 9 g P ( ). Section 07 17 50 - Water Repellent Coatings L. Bond breakers and curing agents shall be removed and the surface cleaned before primers, sealers or finish paints g g P / P
<br /> 16. SAG RESISTANT GYPSUM WALLBOARD: ASTM C 36, manufactured for improved sag resistance, with long edges tapered. Section 09 96 00 - High Performance Coatings can be applied. than 1 inch between panels and walls. Provide brackets, pilaster shoes, bracing, and other components required for a
<br /> Apply on ceilings and similar interior horizontal surfaces. complete installation. Use theft resistant exposed fasteners finished to match hardware. Use sex type bolts for through
<br /> 17. FIRE RESISTIVE TYPE: ASTM C 36, Type X, complyingwith re requirements of fire resistance rated assemblies indicated, and M. All drywall surfaces shall be completely dry and dust free before painting. Skim coated drywall shall be sealed with
<br /> yp q bolt applications.
<br /> 1.02 SUBMITTALS: a sealer recommended by the paint manufacturer for this surface. Use the appropriate light or medium tack 12. STIRRUP BRACKETS: Alin brackets at pilasters with brackets at walls. Locate wall brackets so holes for wall anchors
<br /> with long edges tapered and featured (rounded or beveled) for prefilling. g p'
<br /> A. Product Data: Submit complete manufacturers descriptive literature and specifications in accordance with the masking tape.
<br /> 18. GLASS MAT GYPSUM SHEATHING BOARD: ASTM C 1177. occur in masonry or the joints.
<br /> 19. TILE BACKING PANELS: provisions of Section 01 30 00. 13. Set hinges on in swinging doors to hold open approximately 30 degrees from closed position when unlatched. Set REVISION RECORD
<br /> A. Glass Mat, Water Resistant Board: ASTM C 1178. 1. Materials List: Submit complete lists of materials proposed for use, giving the manufacturer's name, catalog 3.04 APPLICATION: hinges on out swinging doors and swing doors in entrance screens to return to fully closed position.
<br /> B. Cementitious Backer Board ANSI A118.9. number, and catalog cut for each item when applicable. A. Apply painting and finishing materials in accordance with the manufacturers recommendations.
<br /> 20. EXTERIOR AND INTERIOR TRIM: ASTM C 1047, hot dip galvanized steel sheet or rolled zinc. B. Samples: In accordance with provisions of Section 01300, submit, on 8-1/2 inch by 11 inch hardboard, samples of 1. The number of coats specified is the minimum that shall be applied. Apply additional coats when SECTION 10800 - TOILET ACCESSORIES
<br /> 21. JOINT TAPE: ASTM C 475, Interior Gypum Wallboard: Paper, Glass Mat Gypsum Sheathing Board: 10 by 10 glass mesh, each color, gloss, texture and material selected by the Architect from standard colors available for the coatings undercoats, stains or other conditions show through final paint coat, until paint film is of uniform 1. STAINLESS STEEL: ASTM A 666, Type 304, No. 4 satin finish, unless otherwise indicated.
<br /> Tile Backing Panels: As recommended by panel manufacturer. required. finish, color and appearance. 2. BRASS CASTINGS: ASTM B 19, ASTM B 16, or ASTM B 30.
<br /> 22. Joint Compound for Interior Gypsum Wallboard compatible with other compounds applied on previous or for successive 1. For natural and stained finishes, provide sample on each type and quality of wood used on the project. B. Apply each material at not less than the manufacturer's recommended spreading rate: 3. CHROMIUM PLATING: ASTM B 456, Service Condition Number SC 2 (moderate service).
<br /> coats. C. Manufacturer's Instructions: Submit the manufacturer's current recommended methods of installation, including C. Apply prime coat to surface which is required to be painted or finished. 4. MIRROR GLASS: ASTM C 1036, Type I, Class 1, Quality q2, with silvering, electroplated copper coating, and protective
<br /> 23. JOINT COMPOUND FOR TILE BACKING PANELS: Water Resistant Gypsum Backing Board: Use setting type taping and relevant limitations, safety and environmental cautions, application rates, and composition analysis. D. Finish exterior doors on tops, bottoms, and edges same as exterior faces, after fitting. organic coating complying with FS DD-M-411. Repair or replace mirrors that develop visible silver spoilage defects
<br /> setting type, sandable topping compounds. E. Sand lightly and dust clean between succeeding coats. within 15 years from date of Substantial Completion.
<br /> 24. Acoustical Sealant for Exposed and Concealed Joints ASTM E 90and ASTM C 834 Nonsag, paintable, nonstaining, latex 1.03 QUALITY ASSURANCE: 5. GALVANIZED STEEL MOUNTING DEVICEs: ASTM A 153/A 153M, hot dip galvanized after fabrication.
<br /> sealant. A. Regulatory Requirements: Comply with applicable codes and regulations of governmental agencies having jurisdiction 3.05 CLEANING, TOUCH-UP AND REFINISHING: 6. Use fasteners appropriate to substrate tamper and theft resistant when exposed, and of galvanized steel when
<br /> 25. SOUND ATTENUATION BLANKETS: ASTM C 665, Type I blankets without membrane facing. Comply with mineral fiber including those having jurisdiction over airborne emissions and industrial waste disposal. Where those requirements A. Carefully remove all spattering, spots and blemishes caused by work under this section from surfaces throughout the concealed. Install units level, plumb, and firmly anchored in locations and at heights indicated.
<br /> requirements of fire resistance rated assemblies. conflict with this Specification, comply with the more stringent Provisions. project.
<br /> 7. Install grab bars to withstand all loads per applicable Codes.
<br /> 26. Non load bearing steel framing installation. ASTM C 754, and ASTM C 840 requirements for framing installation. Regulatory changes may affect the formulation, availability, or use of specified coatings. Confirm availability of B. Upon completion of painting work remove all rubbish, paint cans, and accumulated materials resulting from work in 8. Adjust accessories for unencumbered, smooth operation and proper function. Remove temporary labels and protective
<br /> 27. Gypsum wallboard installation, ASTM C 840 and GA-216. coatings to be used prior to job going out to bid and before start of painting project. each space or room. All areas shall be left in a clean, orderly condition. a P P P P ry
<br /> B. Runs, sags, misses, holidays, P g q coverage 28. INSTALLING TRIM ACCESSORIES: For trim with back flanges intended for fasteners, attach to framing with same fasteners a. Comply with the current applicable regulations of the California Air Resources Board (GARB) and the Environmental 9 � y , stains and other defects in the pointed surfaces, including inadequate Covera a and mil
<br /> used for panels. Otherwise, attach trim according to manufacturer's written instructions. Protection Agency (EPA). thickness shall be satisfactorily touched up, or refinished, or repainted as necessary. SECTION 11090 - KNOX BOX
<br /> 29. LEVELS OF GYPSUM BOARD FINISH; Gypsum Association GA-214. b. Comply with South Coast Air Quality Management District (SCAQMD) Rule 1113. A copy of this 1. REFERENCE STANDARDS: Comply with the current edition of applicable provisions of the following published specifications
<br /> Level 0: Not used regulation can be obtained from http://www.aqmd.gov/ruies/reg/regil/rlll3.pdf. 3.06 FINISH SCHEDULE:
<br /> and standards unless noted otherwise. Key boxes shall bear UL label.
<br /> Level 1: Wall Spaces above Ceilings. A. Apply the following finishes to the surfaces specified on the finish schedule or on the drawings. Apply all materials
<br /> P 9 B. Field Sample: When and as directed by the Architect, apply one complete coating system for each color, gloss and 2. Order key boxes from manufacturer using original authorization/order form signed by authority having jurisdiction.
<br /> Level 2: Fire Riser Room, Electrical Room, and locations to receive wall tile or F.R.P. in accordance with manufacturer's instructions on properly prepared surfaces and foundation coats. All intermediate
<br /> texture required. When approved, the sample panel areas will be deemed incorporated into the Work and will serve Deliver key boxes to site in good condition, in original unopened packaging, and with labels intact. Inspect materials
<br /> Level 3: Not used. undercoats must be tinted to approximate the final color.
<br /> as the standards by which the subsequent Work of this Section will be judged. 1. Architect will issue a color schedule prior to start of painting to designate the various colors and upon delivery and replace damaged or contaminated materials. Key boxes shall be shipped to contractor. Keys shall be
<br /> Level 4: Dining Room and any locations to receive wall paper. p P g g shipped directly to authority having jurisdiction.
<br /> Level 5: All locations where painted sum board is to be the final finish. locations required for the work. 1 2" solid late door and 1 4" steel
<br /> P 9YP 1.04 DELIVERY, STORAGE, AND HANDLING: 3. KEY BOXES: Provide Model 3200-RTS recessed mounted heavy duty Key Boxes, / p /
<br /> A. Storage and Protection: Use all means necessary to protect the materials of this Section before, during, and after B. Exterior Systems: case in dark bronze finish, or as required by authority having jurisdiction.
<br /> SECTION 09310 - CERAMIC TILE1. Masonry Concrete
<br /> installation. 4. Locate key box as shown on drawings.
<br /> 1. Furnish extra materials matching, products installed. Package with protective covering for storage and identify with a. Gloss - 100% Acrylic PROFESSIONAL SEAL
<br /> labels describing contents. Furnish quantity of full size tStore where directed in accordance with manufacturer's instructions.
<br /> he and trim units equal to 3 percent of amount installed, for B. Deliver materials to job site in new, original, and unopened containers bearing manufacturers name and trade name. First Coat EFF-STOP Premium Masonry Primer/Sealer (ESPR00) 5. Install materials in accordance with accepted shop drawings and manufacturers printed instructions.
<br /> each type, composition, color, pattern, and size. Second Coat EVERSHIELD Exterior Gloss Paint (EVSH60) Color SP514 A R
<br /> Ccy
<br /> 2. Waterproof, Crack Suppression Membranes for Thin Set Tile Installations ANSI A118.10 Manufacturer's standard. 1.05 PROJECT CONDITIONS: Third Coat EVERSHIELD Exterior Gloss Paint (EVSH60) Color SP514
<br /> 3. PORTLAND CEMENT MORTAR THICKSET INSTALLATION MATERIALS: ANSI A108.1A. .bGloss- 100% Acrylicr `
<br /> 4. DRY SET PORTLAND CEMENT MORTAR THIN SET: ANSI A118.1. A. Do not apply exterior materials during fog, rain or mist, or when inclement weather is expected within the dry time F.
<br /> specified by the manufacturer. No exterior or interior painting shall be done until the surfaces are thoroughly dry First Coat EFF-STOP Premium, Masonry Primer/Sealer (ESPR00) G
<br /> 5. CHEMICAL RESISTANT, WATER CLEANABLE, TILE SETTING AND GROUTING EPDXY: ANSI A118.3. and cured. Do not apply paint when temperature is below 50° F. Avoid painting surfaces when exposed to direct Second Coat SYN-LUSTRO Exterior Gloss Paint (W10) Color 221 Safety Red (Red Base)
<br /> 6. WATER CLEANABLE, TILE SETTING EPDXY ADHESIVE: ANSI A118.3. * 2
<br /> sunlight. Third Coat SYN-LUSTRO Exterior Gloss Paint (W10) Color 221 Safety Red (Red Base)
<br /> 7. LATEX ADHESIVE: ANSI A136.1, Type I.
<br /> 2. Concrete Block - CMU
<br /> 8. STANDARD SANDED CEMENT GROUT: ANSI A118.6, color as selected by Architect.
<br /> PART 2 - PRODUCTS a. Gloss - 100% Acrylic
<br /> 9. SAND PORTLAND CEMENT GROUT: ANSI A108.10, color as selected by Architect.
<br /> 10. Elastomeric Sealants One Part, Mildew Resistant Silicone ASTM C 920; Type S; Grade NS; Class 25; Uses NT, G, A, and, First Coat SMOOTH BLOCFIL Premium Concrete Block Filler (SBPR00) - ��
<br /> 2.01 MANUFACTURERS: Second Coat EVERSHIELD Exterior Gloss Paint (EVSH60) Color SP514 '
<br /> as applicable to nonporous joint substrates indicated, 0; formulated with fungicide, intended for in service exposures of A. Manufacturer's catalog names and number of paint types in this Section herein are based on products manufactured Third Coat EVERSHIELD Exterior Gloss Paint (EVSH60) Color SP5142012
<br /> high
<br /> high humidity and extreme temperatures. No substitutionsn
<br /> com and are the basis of design.www.dunnedwards.com www
<br /> the Dunn-Edwards Corp . . g .
<br /> 11. Trowelable Underlayments and Patching Compounds: Latex modified, portland cement based formulation provided or or distributed by b. Gloss- 100% Acrylic (Belly Band)
<br /> approved by manufacturer of tile setting materials. will be allowed. First Coat EFF-STOP Select Masonry Primer/Sealer (ESPROO) tinted to red color
<br /> 12. Remove coatings, curing compounds and other substances that contain soap, wax, oil, or silicone, that are incompatible B. Substitutions: Dunn-Edwards Paint only Second Coat SYN-LUSTRO Exterior Gloss Paint (W10) Color 221 Safety Red (Red Base)
<br /> with tile settingmaterials. Fill cracks, holes, and depressions with trowelable levelingand patchingcompound accordingC. Acceptable Manufacturers
<br /> p P 1. Dunn-Edwards only Third Coat SYN-LUSTRO Exterior Gloss Paint (W10) Color 221 Safety Red (Red Base)
<br /> to tile setting material manufacturer's written instructions. Remove protrusions, bumps, and ridges by sanding or 2. Ferrous Metal
<br /> grinding. 2.02 MATERIALS: a. Gloss - Waterborne Alkyd / 100% Acrylic
<br /> 13. Comply with TCA Installation Guidelines Handbook for Ceramic Tile Installation. A. Paints: Provide ready-mixed, except field catalyzed coatings. Pigments shall be fully ground maintaining soft paste First Coat BLOC-RUST Premium, Anti Corrosive Metal Primer (BRPR00-1 series)
<br /> 14. Extend tile work into recesses and under or behind equipment and fixtures to form complete covering without consistency, capable of being readily and uniformly dispersed to complete homogeneous mixture. Paints shall have Second Coat RUSTOLEUM SIERRA BEYOND Distributed by Dunn-Edwards
<br /> interruptions, unless otherwise indicated. Terminate work neatly at obstructions, edges, and corners without disrupting good flowing and brushing properties and be capable of drying or curing free of streaks and sags. Third Coat RUSTOLEUM SIERRA BEYOND Distributed by Dunn-Edwards PROTOTYPE VERSION
<br /> pattern or joint alignments. B. Accessory Materials: Linseed oil, shellac, solvents, and other materials not specified but required to achieve required 4. Non-Ferrous Metal URBAN DESIGN
<br /> 15. Lay tile in grid pattern, unless otherwise indicated. Align joints when adjoining tiles on floor, base, walls, and trim are finishes shall be of high quality and approved by manufacturer. a. Gloss - Alkyd / 100% Acrylic
<br /> same size. Lay out tile work and center tile fields in both directions in each space or on each wall area. Adjust to C. Colors shall be selected from color chip samples provided by manufacturer of paint system approved for use. Match Pretreatment Supreme Chemical, Metal Clean and Etch (ME 01)
<br /> minimize tile cutting. Provide uniform joint widths, unless otherwise indicated. approved samples for color, texture and coverage. PROJECT NAME
<br /> 16. Grout the per ANSI A108.10, unless otherwise indicated. PP P g First Coat GALV-ALUM Premium, Non Ferrous Metal Primer (GAPR00)
<br /> D. Aromatic Compounds: Paints and coatings shall not contain more than 1.0 percent by weight of total aromatic Second Coat RUSTOLEUM SIERRA BEYOND Distributed by Dunn-Edwards I N N 0 UT
<br /> 17. Install waterproofing per ANSI A108.13 and manufacturer's written instructions to produce waterproof membrane of compounds (hydrocarbon compounds containing one or more benzene rings). Third Coat RUSTOLEUM SIERRA BEYOND Distributed by Dunn-Edwards
<br /> uniform thickness bonded securely to substrate. E. Restricted Components: Paints and coatings shall not contain any of the following: C. Interior Systems:
<br /> 18. Exterior floor installation on concrete TCA F102 thick set portland cement mortar, or Latex Portland cement mortar. 1. Acrolein. 1. Gypsum Board Dining Room Ceiling BURGER
<br /> Sand portland cement grout. 2. Acrylonitrile. a. Eggshell - Acrylic Co-Polymer / 100% Acrylic
<br /> 19. Interior floor installation on concrete TCA F113, Thin Set Dry set portland cement mortar with latex additive. Standard 3. Antimony.
<br /> sanded cement grout. 4. Benzene. First Coat VINYLASTIC Premium, Interior Wall Sealer (VNPR00)
<br /> 20. Interior floor installation on waterproof crack suppression membrane over concrete; TCA F122. Thin Set Latex portland 5. Butyl benzyl phthalate. Second Coat EVERSHIELD Eggshell Sheen Paint (EVSH30) Color IN-N-OUT White
<br /> cement mortar, Polymer modified sanded grout. 6. Cadmium. Third Coat EVERSHIELD Eggshell Sheen Paint (EVSH30) Color IN-N-OUT White LATH RO P
<br /> 21. Exterior wall installation over masonry or concrete; TCA W202. Thin Set Mortar: Dry set portland cement mortar. Sand 7. Di (2-ethylhexyl) phthalate. 2. Gypsum Board Back Room, Office, Locker Room, Restrooms,
<br /> portland cement grout. a. Gloss - 100% Acrylic CALIFORNIA
<br /> 22. Interior d location wall installation; thin set mortar; over sum board; TCA W243 or over cementitious backer units; 8. Di-n-butyl phthalate.
<br /> dry gyp 9. Di-n-octyl phthalate. First Coat VINYLASTIC Premium, Interior Wall Sealer (VNPR00)
<br /> thin set portland cement mortar with latex additive, TCA W244, standard sanded cement grout. 10. 1,2-dichlorobenzene. Second Coat EVERSHIELD Gloss Paint (EVSH60) Color DEW 380 White
<br /> 23. Interior damp locations installation over glass mat, water resistant backer board; TCA B419 and TCA W245 thin set 11. Diethyl phthalate. Third Coat EVERSHIELD Gloss Paint (EVSH60) Color DEW 380 White
<br /> mortar portland cement mortar, Standard sanded cement grout. 12. Dimethyl phthalate. 3. Gypsum Board Dining Room Areas to receive Wallcovering 16514 GOLDEN VALLEY PKWY
<br /> 24. Interior wet location installation TCA 8415 and TCA W244; over cementitious backer units; or TCA 8420 and TCA W245 13. Ethylbenzene. a. Acrylic Co-Polymer
<br /> over glass mat, water resistant backer board portland cement mortar; standard sanded cement grout. 14. Ethylene Glycol. First Coat VINYLASTIC Premium, Interior Wall Sealer (VNPR00) LATHROP, CA 95330
<br /> SECTION 09512 - ACOUSTICAL CEILINGS 15. Formaldehyde. Second Coat 325 Draw-Tite Clear Manufactured by Scotch Paint. (Apply wallcovering with Gardner
<br /> 1. FIRE RESISTANCE RATINGS: Where indicated, provide acoustical tile ceilings identical to those of assemblies tested for 16. Hexavalent chromium. Gibson 433 Heavy Duty Clay Strippable Wallcovering Adhesive. Wallpaper should be hung
<br /> fire resistance per ASTM E 119. Ratings are indicated by design designations from UL's Fire Resistance Directory. 17. Isophorone. with laser to ensure palm trees are level throughout the dining area.)18. Lead. 4. Ferrous Metal Doors and Jams
<br /> Identify materials with appropriate markings of applicable testing and inspecting agency. 19. Mercury. a. SCOPE
<br /> 2. SURFACE BURNING CHARACTERISTICS: Acoustical tiles complying with ASTM E 1264 for Class A materials, when tested per 20. Methyl ethyl ketone. This specification describes a paint system of DuPont Imron Industrial Strength polyurethane primer and
<br /> ASTM E 84. Smoke Developed Index: 450 or less. 21. Methyl isobutyl ketone. Imron Industrial Strength polyurethane high loss topcoat.
<br /> 3. Furnish extra materials matching products installed. Package with protective covering for storage and identify with labels g P Y g g P
<br /> describing contents. Acoustical Ceiling Units: Full size units equal to 2 percent of quantity installed, but not fewer than 23. Naphthalene.22. Methylene chloride. b. GENERAL Ilan"
<br /> NmNmOUT
<br /> 25. 1,1,1-trichloroethane.
<br /> 1 case. Suspension System Components: Quantity of each concealed grid and exposed component equal to 2 percent 24. Toluene (methylbenzene). Modifications must be detailed.
<br /> of quantity installed, but not less than 1 case. C. SURFACE PREPARATION
<br /> 4. ACOUSTICAL TILE STANDARD: ASTM E 1264, Armstrong, USG as scheduled. 25. Vinyl chloride. 1. Prepare the surface in accordance with SSPC-SP2 Hand Tool Clean or SSPC-SP3 Power Tool Clean. `BURGER(D
<br /> 5. METAL SUSPENSION SYSTEM STANDARD: ASTM C 635, Donn, Chicago Metallic, as scheduled. 2. Prior to primer application solvent clean to SSPC-SP1 with T-1021 acetone.
<br /> 6. ATTACHMENT DEVICES: Size for five times design load per ASTM C 635, Table 1, Direct Hung, unless otherwise noted. d. APPLICATION GOD BLESS AMERICA
<br /> 7. Wire Hangers, Braces, and Ties: Zinc coated carbon steel wire; ASTM A 641 Class 1 zinc coating, soft temper. 2.04 MIXES: 1. Handling, mixing, re-coating, dry times and application methods must be in accordance with the
<br /> 8. METAL EDGE MOLDINGS AND TRIM: Manufacturer's standard moldings for edges and penetrations that fit acoustical the A. Mix, prepare, and store painting and finishing materials in accordance with manufacturers directions. manufacturers written instructions.
<br /> edge details and suspension systems indicated; formed from sheet metal of some material and finish for exposed PART 3-EXECUTION 2. On the some day as the surface is cleaned apply the Imron Industrial Strength polyurethane primer at
<br /> flanges of suspension system runners. 3.0 to 5.0 mils dry film thickness.
<br /> 9. Install acoustical tile ceilings per ASTM C 636, seismic requirements, per Code, manufacturer's written instructions, and 3.01 EXAMINATION: 3. After the prime coat has dried sufficiently for re-coat, depending on film thickness, temperature and
<br /> CISCA's Ceiling Systems Handbook. A. Examine surfaces to be painted before beginning painting work. Work of other trades that has been left or installed humidity, apply a top coat of Imron Industrial Strength high gloss polyurethane at 2.0 to 3.0 mils dry
<br /> 10. Paint cut edges of tiles to match face of tiles. in a condition not suitable to receive paint, stain other specified finish shall be repaired or corrected by the film thickness. PROJECT NUMBER
<br /> 11. Suspend ceiling hangers from structural members, plumb and free from contact with insulation or other objects above applicable trade before painting. Painting of defective or unsuitable surface implies acceptance of the surfaces. 4. Total dry film thickness must be at least 5.0 mils minimum. Maximum dry film thickness is 8.0 mils. 180641.001
<br /> ceiling. Splay hangers only where required and, if permitted with fire resistance rated ceilings, to miss obstructions. B. Beware of a condition known as critical lighting. This condition causes shadows that accentuate even the slightest e. INSPECTION
<br /> Offset resulting horizontal forces by bracing, counter splaying, or other equally effective means. Where width of ducts1. All prepared surfaces can be inspected and approved by an owner's representative prior to primer
<br /> surface variations. A pigmented sealer will provide tooth for succeeding decorative coating, but 'does not' equalize application and prior to topcoat application and after rimer and topcoat application. SHEET TITLE
<br /> and other construction interferes with hangers, provide trapezes or equivalent devices. smoothness or surface texture. Any corrective action to drywall must be done by the drywall contractor prior to pp P P pp P P pp
<br /> 12. Install edge moldings and trim at perimeter of ceiling area and conceal edges of acoustical units. Screw attach 2. Dry film thickness of each coat must be measured as described in ASTM D1186 (ferrous substrates).
<br /> moldings to substrate with concealed fasteners at 16 inches o.c. and 3 inches from ends maximum, level with decorating. 3. The completed system must be inspected visually for skips, holidays and uniform color. Defects shall SPECIFICATIONS
<br /> suspension system. Miter corners accurately and connect securely. 3.02 PROTECTION: be repaired before final acceptance.
<br /> E 13. Install suspension system runners square and interlocked. Remove and replace dented, bent, or kinked members. A. Protect previously installed work and materials, which may be affected by Work of this Section.
<br /> 1.Protect prefinished surfaces, lawns, shrubbery and adjacent surfaces against paint and damage. SSPC=Steel Structures Paint Council
<br /> 2. Furnish sufficient drop cloths, shields, and protective equipment to prevent spray or splatter from fouling NOTICE
<br /> surfaces not being painted.
<br /> CD
<br /> 3. Protect surfaces, equipment, and fixtures from damage resulting from use of fixed, movable and hanging Availability of products listed in this specification may be affected by local, state, or federal regulatory requirements for
<br /> C> Cdscaffolding, planking, and staging. architectural coatings. Consult your Dunn-Edwards representative for information on current product availability.
<br /> C>
<br /> B. Provide wet paint signs, barricades, and other devices required to protect newly finished surfaces. Remove temporary SHEET NUMBER
<br /> Qo protective wrappings provided by others for protection of their work after completion of painting operations. END OF SECTION
<br /> m
<br /> zZ
<br />
|