|
GENERAL NOTES
<br /> I m
<br /> 1 . SEE ELECTRICAL SCHEDULE FOR PANEL & CIRCUIT BREAKER
<br /> ASSIGNMENT, VOLT/PH, FLA, BREAKER SIZE, COND/WIRE,
<br /> RECEPTACLE TYPE, HEIGHT ABOVE FINISHED FLOOR,
<br /> REQUIREMENTS & REMARKS FOR ALL ELECTRICAL EQUIPMENT.
<br /> I 2. VERIFY OEP DROP CORDS DO NOT FALL BELOW HEIGHTS LISTED
<br /> ON ELECTRICAL SCHEDULE. RECEPTACLES SHOULD BE LOCATED
<br /> IAT HEIGHTS TO AVOID CONTACT WITH HOT APPLIANCES.
<br /> E.C. SHALL PROVIDE (5) CONVENIENCE OUTLETS WITHIN THE
<br /> DINING AREA FOR CUSTOMER USE, AND (1 ) OUTLET AND DATA 3. RE–USE EXISTING CIRCUITRY AND BREAKERS. CONFIRM
<br /> FOR TELEVISION. E.C. AND G.C. SHALL VERIFY EXACT AMPERAGE AND BREAKER SIZE AS SHOWN ON SCHEDULE. IF
<br /> QUANTITIES AND LOCATIONS IN THE FIELD WITH McDONALD'S NONE, PROVIDE NEW CIRCUIT BREAKER AND WIRE. 0
<br /> AREA CONSTRUCTION MANAGER AND FINAL DECOR DRAWINGS.
<br /> ALL DINNING AREA RECEPTACLES SHALL BE TAMPERPROOF
<br /> TYPE PASS & SEYMOUR "SAFELOCK" 2095–TR OR PROTECTED DEMOLITION NOTES
<br /> BY AN UPSTREAM GFCI TYPE CIRCUIT BREAKER OR DEVICE. w
<br /> E.C. SHALL PROVIDE AT LEAST (2) BRANCH CIRCUITS TO FEED
<br /> THESE CUSTOMER RECEPTACLES AND SHALL PROVIDE ALL D1 . THE ELECTRICAL CONTRACTOR SHALL RELOCATE EXISTING
<br /> IPOWER, DATA, AND TELEPHONE DEVICES IN THE BATHROOM
<br /> MATERIAL AND LABOR FOR A COMPLETE AND FULLY
<br /> FUNCTIONAL OUTLET SYSTEM. THESE OUTLETS SHALL NOT BE AREAS TO BE AFFECTED. REFER TO DEMO PLAN D1 .0 FOR
<br /> AFFECTED AREA.
<br /> ISOLATED GROUNDING TYPE. TOTAL ADDED LOAD 9 AMPS.
<br /> REUSE EXISTING DINING AREA RECEPTACLE CIRCUITRY WHERE
<br /> POSSIBLE. D2. THE ELECTRICAL CONTRACTOR SHALL RELOCATE EXISTING
<br /> POWER, DATA, AND TELEPHONE DEVICES FOR THE WALL
<br /> RELOCATION. REFER TO DEMO PLAN D1 .0 FOR AFFECTED
<br /> AREA.
<br /> D3. RE–USE EXISTING CIRCUITRY AND BREAKERS. CONFIRM
<br /> CP:* IF THERE IS NOT SUFFICIENT CAPACITY IN THE EXISTING AMPERAGE AND BREAKER SIZE AS SHOWN ON SCHEDULE. IF
<br /> COMPUTER PANEL FOR THE NEW COMPUTER CIRCUITS , THEN NOT, PROVIDE NEW CIRCUIT BREAKER AND WIRE,
<br /> CONTRACTOR IS TO REPLACE THE EXISTING PANEL WITH A NEW 42 w
<br /> NOT IN SCOPE OF CIRCUIT PANEL OF THE SAME AMPACITY AS EXISTING. NEW PANEL Q
<br /> WORK SHALL BE OF THE SAME MAKE, MODEL, MANUFACTURER AND HAVE KEY NOTES Q
<br /> THE SAME AIC RATING AS THE PANEL BEING REPLACED. PROVIDE POWER WITHIN CEILING FOR CONNECTION TO SELF ORDER
<br /> KIOSKS. COORDINATE EXACT LOCATION OF KIOSKS WITH DECOR w
<br /> DRAWINGS. PROVIDE 2#12,1 #12 GRD., & 1 #12 ISOLATED GROUND ON
<br /> A 20A DEDICATED CIRCUIT FED FROM THE CP PANEL FOR EVERY ONE ENGINEER of RECORD:
<br /> (1) DOUBLE SIDED OR TWO (2) SINGLE SIDED KIOSKS. IF
<br /> RESTAURANT DOES NOT RECEIVE KIOSK, PROVIDE J–BOX AND 112" Eft
<br /> CONDUIT WITH PULL STRINGS TO TWO (2) SPARE 20A/1 P BREAKERS FER
<br /> WITHIN CP PANEL. "ALL ELECTRICAL FEEDS FOR THE KIOSKS ARE TO
<br /> HANDLED BY THE GENERAL CONTRACTOR'S ELECTRICIAN ON SITE." / 7
<br /> ❑3 I VERIFY IF OPTIONAL TABLE TRACKER SYSTEM IS TO BE USED. IF
<br /> USED, PROVIDE 2#12, 1#12 GRD, & Y,2 ISOLATED GRD. TO AVAILABLE SOF CA0'f°
<br /> \ SPARE 20A/1 P BREAKER WITHIN CP PANEL. CONNECT CIRCUIT TO 9/6/19
<br /> — — — — — — TWO (2) IG RECEPTACLES, ONE (1 ) RECEPTACLE FOR SERVER
<br /> C� (TYPICALLY LOCATED IN I.T. CLOSET AND ONE (1 )RECEPTACLE FOR
<br /> MONITOR (TYPICALLY LOCATED AT HLS OR PICKUP COUNTER).
<br /> COORDINATE EXACT LOCATION(S) IN THE FIELD AND REQUIREMENTS W , 0
<br /> 4 7 WITH MANUFACTURER'S INSTALLATION INSTRUCTIONS.
<br /> NEW DIGITAL MENU BOARD. CATV TYP. 0 CP:* 3 EXISTING POWER N THIS AREA TO REMAIN.
<br /> REUSE EXISTING CIRCUITRY ❑
<br /> AND CONTROL. REFER TO
<br /> DIGITAL MENU BOARD DETAIL FOR RECEPTACLE CIRCUITRY REFER TO THE BOX NOTE ON THIS
<br /> ❑ 10 14 ON SHEET E4.0. [4] SHEET. COORDINATE FINAL LAYOUT WITH DECOR AND OWNER y
<br /> 3 OPERATOR. TYPICAL.
<br /> 14 10 5 EC SHALL PROVIDE A DUPLEX RECEPTACLE AND A LOW VOLTAGE W
<br /> 13 BROADBAND CONNECTION FOR THE INSTALLATION OF FLAT PANEL m , Q
<br /> TELEVISIONS. COORDINATE EXACT LOCATIONS WITH DECOR COMPANY. , a
<br /> FOR BROADBAND CONNECTION, EC SHALL PROVIDE A 4 X 4 BOX O <'T
<br /> w }�u�a)
<br /> °
<br /> WITH A 3/4" CONDUIT STUB–UP WITH A BUSHING INTO ACCESSIBLE
<br /> w� a°
<br /> o ❑ 0 CEILING SPACE. RE–USE EXISTING CIRCUITRY.
<br /> J
<br /> I
<br /> 6 I I I 0 ❑6 ROUGH IN FOR FUTURE DIGITAL BULLETIN BOARD. CONFIRM LOCATION °
<br /> v WITH ACM. o
<br /> .a
<br /> PROVIDE AN ALLOWANCE IN BID TO PROVIDE TWO(2) FLEXIBLE POWER °Q o � �o o.o
<br /> ❑3 I I U - CP:* ID
<br /> CONNECTIONS FOR POWER TO FURNITURE/ FAMILY EXPERIENCE o
<br /> ° ELEMENTS AS PART OF THE DECOR PACKAGE. VERIFY EXACT J Q L ° 0 °
<br /> 1 LOCATIONS IN FIELD AND WITH DECOR DRAWINGS. PROVIDE ALL ° °' a ° °
<br /> a o � a
<br /> NECESSARY MATERIALS AND LABOR FOR A COMPLETE AND FULLY NEC o a) �
<br /> FIELD VERIFY CODE COMPLIANT INSTALLATION. ALL COMPONENTS SHALL BE FED a o I U' L
<br /> LOCATIONS OF EXISTING I I 9 FROM A GFCI TYPE CIRCUIT BREAKER AND BRANCH CIRCUIT SHALL ° Q) N
<br /> POWER PANELS 12 8 CONTAIN TWO PATHS OF GROUNDING (CONDUIT BODY AND AN ° a D �_ a o Q
<br /> t a
<br /> INSULATED GROUNDING CONDUCTOR) TO COMPLY WITH McDONALD'S o -°a .3 a ° °
<br /> GROUNDING STANDARDS. @ L o a-
<br /> - L° ° La °
<br /> ❑3 II ii REUSE EXISTING FRONT COUNTER CIRCUITS WHERE POSSIBLE. REFER o �.N E-
<br /> Q� ii 0 0 TO DETAIL ON SHEET E4.0. PROVIDE (4) 20A, 120V I.G. CIRCUITS a ° o a , °
<br /> P:* FROM PANEL CP TO FEED FRONT COUNTER POS EQUIPMENT, TABLE co� a
<br /> — U U
<br /> TRACKERS AND UBER TABLET. (1 ) 20A, 120V CIRCUIT FROM A SPARE
<br /> 1 C/B IN AN AP PANEL TO FEED 2 DCO'S SERVING THE BAKED GOODS o o
<br /> II 11 C� DISPLAY. IF THERE IS NOT SUFFICIENT CAPACITY IN THE EXISTING u w a
<br /> �fl I COMPUTER PANEL FOR THE NEW COMPUTER CIRCUITS, THEN 0 _� °"L o�.�
<br /> � _ �
<br /> I II 13 CONTRACTOR IS TO REPLACE THE EXISTING PANEL WITH A NEW 42 Q a ° L >
<br /> Q n L
<br /> CP:* I CIRCUIT PANEL OF THE SAME AMPACITY AS THE EXISTING. NEW PANEL u o o o ° Q 0,
<br /> DUAL POINT FRONT SHALL BE OF THE SAME MAKE, MODEL, MANUFACTURER AND HAVE N o 0 oa
<br /> °
<br /> 2 I� THE SAME AIC RATING AS THE EXISTING PANEL.
<br /> ,
<br /> COUNTER LAYOUT CONFIRM � ° Q
<br /> L — LAYOUT WITH MCD o o L o o i
<br /> EXISTING SELF SERVICE CONSTRUCTION SUPERVISOR ELECTRICAL RACEWAY PROVIDED WITH COUNTER AND INSTALLED BY o ® a ' 3 ° ocn 0
<br /> BEVERAGE BAR. REFER TO DETAIL ON w ° o - °.0 o
<br /> E.C. REFER TO DETAIL ON SHEET E4.0 0- a� U) s
<br /> 13 SHEET E4.0 w ° L
<br /> RELOCATE/REUSE EXISTING ELECTRICAL CIRCUITRY o a
<br /> H a i C n
<br /> FOR THE KITCHEN EQUIPMENT ASSOCIATED WITH I EXISTING POWER IN BATHROOMS TO BE RELOCATED AS NEEDED PER w
<br /> THE SERVICE AREA MODERNIZATION. NO — — — — — — — — — —— 10 NEW ADA COMPLIANT BATHROOM LAYOUT. EXTEND EXISTING CONDUIT z o
<br /> ADDITIONAL LOADS WILL BE ADDED. ❑ ® I r Q0
<br /> �3 3 AND CIRCUITRY TO NEW DEVICE LOCATIONS. NO ADDITIONAL LOADS m o o m o o w
<br /> WILL BE ADDED TO EXISTING CIRCUITS. z w N -D � o N
<br /> ® ILil
<br /> Q U w w 01 w a l
<br /> 1 1
<br /> 1 .5" CONDIUIT AND BOX AT 7'-10" FOR RELOCATED ORB. REUSE o o � o � c
<br /> ' EXISTING POWER AND DATA o C
<br /> ❑ DRAFT STOP ABOVE CEILING. E.C. TO ENSURE INTEGRITY OF FIRE
<br /> 12 RATED WALLS WHERE ELECTRICAL EQUIPMENT PENETRATES WALLS.
<br /> 1 ELE�TRIAO�CPOWER PLAN SEAL PER SPECIFICATIONS FOR FIRE STOPPING. z
<br /> 0
<br /> Y
<br /> CJ
<br /> E1 . 1 1 4" — � ' ❑ EXTEND 2 1/2" CONDUIT FROM 1 '-2" AFF TO ABOVE CEILING FOR o
<br /> 13 POS DATA CABLES. IF THERE IS NOT ENOUGH SPACE IN WALL TO cn
<br /> ROUTE CONDUIT TO ABOVE CEILING, CONTRACTOR TO TRENCH TO
<br /> NEAREST FULL HEIGHT WALL AND EXTEND 2 1/2" CONDUIT TO ABOVE
<br /> CEILING. w
<br /> SYMBOLS AND ABBREVIATIONS SYMBOLS AND ABBREVIATIONS >_
<br /> Q
<br /> SYMBOL DESCRIPTION SYMBOL DESCRIPTION SYMBOL DESCRIPTION SYMBOL DESCRIPTION 14 ELECTRICAL CONTRACTOR TO CONFIRM RESTROOM CIRCUITRY Is ON U o z
<br /> MCDONALDS PANELS. IF NOT THEN COORDINATE OUTAGES WITH O
<br /> CONVENIENCE STORE MANAGEMENT. z w cl� >
<br /> SINGLE POLE SWITCH, 3W=THREE WAY SWITCH, K=KEYED SWITCHED, g0 BUZZER OS STUB UP THRU ROOF IG ISOLATED GROUND0 J w
<br /> VSVACANCY SENSOR O Q D co _
<br /> I� ( ) © BUTTON FOR BUZZER 0 THERMOSTAT SENSOR W/ 1/2"C– UP TO CEILING SPACE JB JUNCTION BOX �
<br /> T MANUAL SWITCH T=THERMAL OVERLOADS o w o U)
<br /> w
<br /> MOTOR CONNECTION KFS KITCHEN EQUIPMENT SUPPLIER LL m a
<br /> ❑T TRANSFORMER o o PULLBOX L_ w w Ln
<br /> MLO MAIN LUGS ONLY ELECTRICAL LOAD CALCULATION z o
<br /> CONDUIT RUN CONCEALED IN CEILING OR WALLS O
<br /> ® JB WITH DUPLEX CONVENIENCE OUTLET (FLUSH WITH CEILING) G PANELBOARD — W O Q 1,
<br /> EXISTING INTERIOR LIGHTING REMOVED -5.7 KW
<br /> / \ CONDUIT RUN IN FLOOR SLAB WP WEATHERPROOF z o U z
<br /> �{ JB WITH SINGLE CONVENIENCE OUTLET O O CIRCUIT BREAKER NEW COMPUTER CIRCUITS 2.5 KW � � w 00
<br /> HOT (SHORT), NEUTRAL (LONG), EQUIP GRD (LONG WITH DOT), & pp CARBON MONOXIDE SENSOR — w
<br /> JB WITH DUPLEX CONVENIENCE OUTLET A AMPERES �X & 'X' DENOTES ISOLATED GRD NEW INTERIOR LIGHTING 1.0 KW J O X 0 o �
<br /> x Li
<br /> JB WITH TWO DUPLEX CONVENIENCE OUTLETS ACM AREA CONSTRUCTION MANAGER TOTAL NETADDED LOAD - -2.2 KW N W w U W
<br /> J–BOX WITH FINAL EQUIPMENT CONNECTION o
<br /> JB WITH SPECIAL PURPOSE OUTLET AFF ABOVE FINISHED FLOOR OS CEILING MOUNTED OCCUPANCY SENSOR NEW ESTIMATED LOAD - -2.2
<br /> NEW ESTIMATED LOAD AMM PS - -6.2 AMM
<br /> PS
<br /> ® JB WITH ISOLATED GROUND OUTLET C CONDUIT N INTERCOM STATION W/ 3/4"C TO MAIN STATION EC ELECTRICAL CONTRACTOR
<br /> =IG4700A, =IC5262
<br /> IG4710, '.' =IG5261 , '� CCT CIRCUIT TELEPHONE JACK GC GENERAL CONTRACTOR E 1 9 1
<br /> ❑� DISCONNECT SWITCH GND GROUND OJ JUNCTION BOX WALL OR CEILING MOUNTED GFI/GFCI GROUND FAULT CIRCUIT INTERRUPTER U) POWER PLAN
<br />
|