SR0082783 - Laserfiche WebLink

Home Browse Search

VINYLTECH AWWA VINYLTECH V�NYLTECH AWWA Vl.YMTECH C900BLUE SUBMTECHITITAL(4"-112") rCAL DATA m C900 BLUE Vil Effective 11/17 TECHNICAL DATA SUBMITTAL (4" - 12") C900 DR 18 Pressure Class 235 PVC - PIPE NOMINALSIZE OUTER MINIMUM FEET PER LIFTS PER APPROX WEIGHT CONFORMANCE MARKING (IN) (mm) DIAMETER(IN) WALL(IN) LIFT TRUCK (LB/100') . These specifications designate the requirements for The pipe shall be marked in accordance with AWWA C900. 4 100 4.800 0.267 1020 16 257 6 manufacturing and Installing Vinyltech AWWA C900 PVC 6 150 6.900 0.383 440 16 521.2 Pressure Pipe for potable water(4"-12"). QUALITY CONTROL 8 200 9.050 0.503 200 20 903.0 ANSI/AWWA C900-Polyvinyl Chloride(PVC)Pressure Pipe Each length of the pipe Including the bell shall be 10 250 11.100 0.617 240 12 1364.4 and Fabricated Fittings,4"Through 60"(100mm Through hydrostatically tested in accordance with AWWA C900.The 12 300 1 13.200 0.733 60-80 28 1 1935.8 1,500mm) pipeshall meet all additional test requirements as described in AWWA C605-Underground Installation of Polyvinyl Chloride AWWA C900.Our full-time quality assurance staff continually (PVC)Pressure Pipe and Fittings for Water administers a rigid program of tests to maintain the production C900 DR 14 Pressure Class 305 ASTM 01784 - Standard Specification for Rigid Poly(Vinyl of the best pipe products available. Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride)(CPVC)Compounds INSTALLATION NOMINAL SIZE OUTER MINIMUM FEET PER LIFTS PER APPROX WEIGHT ASTM D3139 - Standard Specification for Joints for Plastic (IN) (mm) DIAMETER(IN) WALL(IN) LIFT TRUCK (LB/100') M Pressure Pipes Using Flexible Elastomeric Seals Recommended Installation procedures of Vinyltech ASTM F477-Standard Specification for Elastomeric Seals Corporation are outlined in AWWA C605, Underground 4 700 4.800 0.343 1020 16 317.5 (Gaskets)for Joining Plastic Pipe Installation of Polyvinyl Chloride(PVC) Pressure Pipe and 6 150 6.900 0.493 440 16 658.7 Fittings for Water.The AWWA Manual PVC Pipe Design NSF/ANSI 61,Annex G l Drinking Water Systems Components- 8 200 9.050 0.646 200 20 1139.7 and Installation,is also an Invaluable resource guide for design Health Effects 10 250 11.100 0.793 240 12 7722.3 FM 1612-Approval Standard for Polyvinyl Chloride(PVC)Pipe and installation. and Fittings for Underground Fire Protection 12 300 13.200 0.943 60-80 28 2445.5 N UL 1285-Standard for Pipe and Couplings,Polyvinyl Chloride TAPPING (PVC), and Oriented Polyvinyl Chloride (PVCO) for The consistent success of tapping PVC pressure pipe Is 6A Underground Fire Service contingent upon the use of proper procedures and equipment. 0 Vinyltech recommends strict compliance with the PIPE COMPOUND requirements as specified in AWWA 0605. 10 The pipe shall be extruded from compounds meeting ASSEMBLING THE PIPE (PVC 1120)the requirements of Cell Classification 12454,as defined In ASTM 01784,Standard Specification for Rigid Poly Assembly of Vinyltech PVC water pipe Is easily accomplished. 4.o:) (Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl A depth of entry mark is on each spigot end to serve as a visual gill 11 Chloride)(CPVC)Compounds.The PVC shall also be listed by check for rapid,accurate joint Inspection.Do not over Insert. the National Sanitation Foundation(NSF)for use In potable water. 1) Remove any mud,sand,or other foreign matter from the SEALING POINTS V l belled and spigot ends of the pipe.Carefully clean the PIPE gasket area. Vinyltech pipe shall be manufactured in accordance with 2) With a clean applicator(a brush or hand)lubricate the AWWA C900. entire surface of the pipe from the spigot end to the depth of entry mark and the contact surface of the The R i e b e r Factory installed,locked-in gasket GASKET JOINT gasket with Vinyltech Brand Lubricant. 3) Brace the bell to avoid disturbing the already installed •The pipe bell forms over the gasket,making a perfect fit The gasket shall be reinforced with a steel band and meet the Joints.Align the pipe,insert the spigot into the bell and requirements of ASTM F477.Vinyltech pipe shall have an push. Sealing System Avoids the possibility of installing the wrong gasket Integral bell end with a locked-in factory installed gasket and 4) Do not Insert past the entry mark line. The Rieber system provides a proven pipe Reduces installation problems shall meet the joint requirements of ASTM D3139. joint with an excellent track record in the The locked-in gasket eliminates gasket roll-out during joining '\\ g Underwriters field.It is the fastest growing system in the The gasket is molded vs.extruded and spliced 'U11 La6oraeories Inc.® F M R�� world because of its many advantages. •Works equally well under pressure or vacuum / .� ries u.ren Three sealing points achieved vs.two APPROVED •LEAK-PROOF JOINTS `THE WORLDS BEST JOINT' VINYLTECH • 201 S.61st Avenue Phoenix,AZ 85043 • 602 233-0071 • Fax:602 272-4847 www.vtpipe.com u, 01TERTAILcow•nw 201 S.61st Avenue•Phoenix,AZ 85043 V 602 233-0071.602 272-4847 Fax•wwwvtpipe.com QTTERTAIL n ow ..