|
authorized, substances orcomponents; soil or other CAUTION
<br /> surface or subsurface conditions; or fire, flood, storm, Do not remove elastic band from around float until
<br /> lightning, earthquake, accident or any other conditions, instructed to do so, as damage to valve may result.
<br /> events or circumstances beyond OPW's control . WARWI.N
<br /> THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER Failure to properly connect delivery hose andel-
<br /> WARRANTIES, EXPRESS OR IMPLIED, AND ALL OTHER bow, and/or disconnecting aliquid filled delivery
<br /> WARRANTIES INCLUDING, WITHOUT LIMITATION, THE hose or elbow will result in a hazardous spill, which
<br /> WARRANTIES OF MERCHANTABILITY AND FITNESS FOR may result in personal injury, property damage, fire,
<br /> A PARTICULAR PURPOSE, ARE HEREBY EXCLUDED. . explosion, and water and soil pollution.
<br /> OPW shall have no other liability whatsoever, whether • Make Sure all connections, including the hose and
<br /> based on breach of contract, negligence, gross negli- elbow connections, between storage tank and
<br /> gence, strict liability or any other claim, including, with- transport are securely coupled.
<br /> out limitation, for special, Incidental, consequential or
<br /> exemplary damages or for the cost of labor, freight, ex- • Make sure the lip seal and/or all gaskets in the deliv
<br /> cavation, clean-up, downtime, removal, reinstallation, ery elbow are properly in place to prevent spills.
<br /> loss of profit, or any other cost or charges. No person or . Do not operate with damaged or missing parts,
<br /> entity is authorized to assume on behalf of OPW any which prevent tight connections.
<br /> liability beyond this limited warranty. This limited war-
<br /> ranty is not assignable. Normal Operation: A Hose " Kick" and reduced flow
<br /> signal that the tank is full , Close transport delivery
<br /> Date of manufacture on this product is located on valve and drain hose into tank before disconnecting
<br /> the flat area of the valve body, under float. any hose fitting .
<br /> Overfilled Tank. Failure of the hose to drain after
<br /> GENERAL INSTRUCTIONS closing the delivery valve signals an overfilled tank. Do
<br /> The OPW 7150 Overfill Prevention Valve is designed for Not Disconnect any delivery hose fitting until the liquid
<br /> tight fill, gravity drop applications to help prevent acci- level in the tank has been lowered to allow the hose to
<br /> dental or intentional overfilling of underground storage drain Into the tank.
<br /> tanks. It is installed in the UST drop tube In place of a WARNiNg
<br /> standard drop tube. In the event you are splashed with fuel remove wet
<br /> The main 71 SO valve closes when liquid reaches the clothing immediately. Skin contactwith gasoline
<br /> initial shut off point. A small bypass valve remains open can cause chemical burns and may result in inhala-
<br /> to allow the delivery hose to drain at 3-5 gallons per tion of vapors that may be fatal. Never go inside
<br /> minute. If the delivery truck valve is not closed after confined areas after being splashed and never go
<br /> initial shut-off, the bypass valve will close and will re- near ignition sources*
<br /> strict all fuel delivery to ensure that the top of the tank IMPORTANT
<br /> is not wetted per EPA requirements. Determine if the underground storage tank is equipped
<br /> The 7150 models of the 71 SO are designed to be in - with a ball float vent valve, as illustrated in Figure 24. In
<br /> stalled with the following OPW products: Face Seal all systems, the shut-off point of the 7150 must be
<br /> Adaptor, OPW Spill Container or Multi port, Jack Screw reached before the ball float reduces flow to ensure
<br /> Kit, Rotatable Product Adaptor, and Product Cap. proper overfill valve operation.
<br /> IMI QRTANT TOOLS NEEDED FOR INSTALLATION AND ASSEM-
<br /> Read these assembly and installation instructions com� "LY;
<br /> pletely and carefully prior to starting. Check to make 1 . 7150-TOOLor 71SO TOOLCor
<br /> sure all parts have been provided . Use only the parts
<br /> supplied, substitution of parts may cause product fall- 71 SO-TOOLCT (includes the following)
<br /> ure. • Sharp 3/16" drill bit with stop
<br /> Failure to follow instructions may cause improper prod- . Punch
<br /> uct operation or premature failure which may permit NC}7 Testable 71 SO models ending with a uT" re-
<br /> storage tank overfill . An overfilled storage tank may
<br /> create hazardous conditions and/or environmental can- cl'uiro the 71 SOTOOLCT or modified 71 SA-Toot or
<br /> tamination. 71 SO-TOOLC
<br /> 2
<br />
|