Laserfiche WebLink
4HZ32G thru 4HZ59G, 5DVN6 thru 5DVN9, <br /> 5DVP0 thru 5DVP9, 5DVR0 thru 5DVR4, <br /> Dayton Operating Instructions and Parts Manual 6KWH7 thru 6KWH9, 6KW10 thru 6KWJ3 <br /> Daytone Centrifugal Direct-Drive <br /> Upblast Exhaust Ventilators <br /> General Safety Information —,A WARNING Do not use a damper diagram.See Electrical Connection, <br /> Continued Figure , <br /> or speed control in Fi 7page 5.Wire control <br /> P 9 <br /> any kitchen exhaust application. switches at ground level. <br /> Protection Association (NFPA) JA Do not raise <br /> Bulletin 96 in the United States. CAUTION ventilator by its 10.Replace motor[aver. <br /> Ground motor in accordance with windband,use a sling or platform. 11.A drain trough is provided on <br /> NEC Article 250 (grounding). Follow ROOF-MOUNT all Dayton roof mount upblast <br /> the Canadian Electric Code(CEC) in ventilators. Collection for grease and <br /> Canada. -� 0-°m ' residue must be provided. <br /> © CAUTION To reduce the risk {MALL-(MOUNT <br /> of injury to persons, <br /> observe the following: wex <br /> OSHA requires OSHA complying guards <br /> when fan is installed within 7 feet of <br /> floor or working level. VAuft*Q �—ad <br /> w twt HM oee awe <br /> ULIcUL Standards require OSHA <br /> complying guards when fan is installed 6WA <br /> within 8 feet of floor or working level, aooe o a�w�mo�a <br /> Duct end—� <br /> 4. Do not kink power cable or allow Optlaul <br /> it to come in contact with sharp <br /> objects, oil, grease, hot surfaces or Figure 3—Typical Roof-Mount Figure 4—Typical wall-Mount <br /> chemicals. Replace damaged cords 1. Cut an appropriate sized hole <br /> 1. Remove venturi mounting plate <br /> immediately. in the roof surface. Follow curb from ventilator by removing the <br /> 5. Make certain that the power source manufacturer's installation fasteners. <br /> conforms to the requirements for instructions. Caulk and flash curb to <br /> the equipment. 2. Remove motor cover by removing <br /> ensure a water tight seal. fasteners. <br /> 6. Never open access door to a duct 2. Install optional backdraft damper. <br /> 3. Locate the mounting plate at the <br /> with the ventilator running. Secure damper flange to curb <br /> desired position and check to avoid <br /> 7. Motor must be securely and damper tray,with fasteners <br /> unit clearance problems(buildings <br /> adequately grounded.This can provided. and people). <br /> be accomplished by wiring with 3. Remove motor cover by removing <br /> rounded, metal-clad race way 4. Cut the appropriate size square <br /> a <br /> 9 y fasteners. opening in the wall. <br /> system by using a separate ground q place ventilator on curb. <br /> wire connected to the bare metal of 5. Install optional backdraft damper <br /> the motor frame, or other suitable 5. Secure ventilator to roof curb using with directional arrow pointing up. <br /> means. a minimum of eight fasteners. 6. Locate top of mounting plate and <br /> Installation 6. Check ventilator wheel for free attach to the wall structure.The <br /> Installation, rotation. fasteners must pass through the <br /> ©WARNIN!:Ij troubleshooting and 7. Check all fasteners for tightness. holes provided in the mounting <br /> parts replacement is to be performed 8. Install NEC 70 requirements for angle clips on the mounting plate. <br /> only by a qualified personnel. Consult For uneven surfaces, shims may be <br /> and follow NFPA 96 recommendations. Restaurant Exhaust of Appliances. <br /> required. <br /> !NFPA 96 instructions supersede this 9. Mount and wire safety disconnect <br /> document. switch under ventilator cover and <br /> wire motor per connection wiring <br /> 4 <br />