WORK PLANS - Laserfiche WebLink

Home Browse Search

DIVISION 09 - FINISHES DIVISION 31 - EARTHWORK GYPSUM BOARD QUALITY CONTROL SOILS REPORT: CERAMIC TILE WALL COVERING MATERIAL SHALL MEET OR EXCEED THE FOLLOWING STANDARDS INSTALLATION OF ACCESSORIES: INSTALL CORNER TRIM AT VERTICAL AND DIVISION 10 - SPECIALTIES THIS SECTION IS NOT USED HORIZONTAL EXTERNAL CORNERS AND ANGLES, AND EDGE TRIM AT ALL WORK SHALL BE IN CONFORMANCE WITH THE SOILS, COMPACTION AND JUNCTIONS OF WALLBOARD AND OTHER MATERIALS AND AT EXPOSED EDGES. DIVISION 11 - EQUIPMENT THIS SECTION IS NOT USED GEOLOGICAL REPORT. 1. TILE: INTERCERAMIC 1. FRP WALL PANELS CEMENT PLASTER -3 COAT SYSTEM : T-1 16x24 CERAMIC, HABITAT DURABODY, SMOKE FRP-1 : WALL PANELS • APPLICATION SHALL BE IN COMPLIANCE WITH APPLICABLE SECTIONS OF TAPING AND FINISHINGFINISH LEVELS: UNLESS OTHERWISE SCHEDULED, DIVISION 12 - FURNISHINGS THIS SECTION IS NOT USED THE CONTRACTOR SHALL HAVE THE SOILS ENGINEER REVIEW AND - PATTERN: 1/2 RUNNING BOND IN RESTROOM / - MANUFACTURER: MARLITE ANSI A42.2 "PORTLAND CEMENT AND PORTLAND CEMENT-LIME REQUIRED FINISH LEVELS FOR VARIOUS AREAS SHALL BE AS FOLLOWS: STACKED BOND IN HALLWAY REF: INTERIOR -COLOR: P-100 (WHITE) PLASTERING, EXTERIOR (STUCCO)AND INTERIOR"'AND ANSI A42.3 APPROVE IN WRITING TO THE BUILDING OFFICIAL AND ARCHITECT THAT ELEVATIONS - FINISH: SMOOTH GLOOC, PEBBLE FINISH DIVISION 13 - SPECIAL CONSTRUCTION THIS SECTION IS NOT USED THE FOUNDATION AND SITE DESIGN ARE IN CONFORMANCE WITH THE "LATHING AND FURRING FOR PORTLAND CEMENT AND PORTLAND LEVEL 1: EMBED TAPE AT JOINTS IN CEILING PLENUM AREAS, CONCEALED SOILS REPORT PRIOR TO COMMENCEMENT OF WORK. - GROUT LINE: 3/16" - FIRE CLASSIFICATION: TYPE C CEMENT-LIME PLASTERING, EXTERIOR (STUCCO)AND INTERIOR. AREAS, UNLESS A HIGHER LEVEL OF FINISH IS REQUIRED FOR FIRE- DIVISION 14 - CONVEYING SYSTEMS THIS SECTION IS NOT USED -THINSET: VERSABOND GRAY THINSET, 50LB BAG - FLAME SPREAD: <200 • IN ADDITION, MATERIALS SHALL MEET OR EXCEED THE FOLLOWING: RESISTANCE-RATED ASSEMBLIES AND SOUND-RATED ASSEMBLIES. - GROUT: POLYBLEND SANDED GROUT, #183 -SMOKE DENSITY: <450 • THE CONTRACTOR SHALL BE SOLELY RESPONSIBLE FOR COMPLIANCE PORTLAND CEMENT: ASTM C 150, TYPE I, NATURAL COLOR. SPECIAL LEVEL 2: EMBED TAPE AND APPLY SEPARATE FRIST COAT OF JOINT DIVISION 15-20 - UNASSIGNED THIS SECTION IS NOT USED WITH ALL RECOMMENDATIONS OF THE SOILS REPORT. CHATEAU, 25 LB BAG - LIGHT RV: 83.0%T-2 : 7x36 CERAMIC, SUNWOOD PRO DURABODY, - NOTE: APPLY WITH MARLITE C-375 FINISHING HYDRATED LIME: ASTM C 206, TYPE S. AGGREGATES: ASTM C COMPOUND ON TAPE, FASTENERS, AND TRIM FLANGES WHERE GYPSUM 144, ALL SAND TO PASS NO. 8 SIEVE. CEMENT PLASTER FINISH COAT: A PANELS ARE THE SUBSTRATE FOR TILE. LEGEND BEIGE CONSTRUCTION ADHESIVE MOLDING AT ALL INSIDE PACKAGED BLEND OF PORTLAND CEMENT (ASTM C 150), HYDRATED LIME PRIOR TO THE CONTRACTOR REQUESTING A FOUNDATION INSPECTION BY - PATTERN: 1/3 OFFSET RUNNING BOND CORNERS, AND "J" MOLDING WHERE WALL PANEL LEVEL 3: EMBED TAPE AND APPLY SEPARATE FIRST AND FILL COATS OF JOINT DIVISION 21 - FIRE SUPPRESSION THE BUILDING DEPARTMENT, THE SOILS ENGINEER SHALL ADVISE THE 5865 Owens Drive (ASTM C 206), AND PROPERLY GRADED QUALITY 20 MESH AGGREGATE, COMPOUND TO TAPE, FASTENERS, AND TRIM FLANGES, WHERE GYPSUM BUILDING OFFICIAL AND ARCHITECT IN WRITING THAT: - GROUT LINE: 3/16" TERMINATED. WITH INTEGRAL COLOR AND PAINT FINISH. MIXES: JOB-MIXED CEMENT PANELS ARE THE SUBSTRATE FOR HEAVY TEXTURED FINISHES AND WHERE -THINSET: VERSABOND GRAY THINSET, 50 LB BAG Pleasanton, CA 94588 PLASTER MIX, BONDCRETE OR MORTASEAL MASON'S LIME WITH LIGHTING CONDITIONS ARE NOT CRITICAL. 21.01 GENERAL REQUIREMENTS SITE GRADING, SUBGRADE PREPARATION, CUTTING SLOPES, EXCAVATION, - GROUT: CBP POLYBLEND SANDED GROUT, #183 2. WALK-IN COOLER UNIT WALLS: 925-251-7200 PORTLAND CEMENT AND SAND IN ACCORDANCE WITH ANSI A42.2, TYPE L. LEVEL 4: EMBED TAPE AND APPLY SEPARATE FIRST, FILL, AND FINISH COATS FIRE SPRINKLER SYSTEM SHALL BE "DESIGN-BUILD"AND ARE NOT A PART OF PLACEMENT OF ENGINEERED FILL MATERIAL AND COMPACTION IS IN CHATEAU, 25 LB BAG INTERIOR: SMOOTH PEBBLE TEXTURE GALVINIZED SKIN PROPORTIONS: OF JOINT COMPOUND TO TAPE, FASTENERS, AND TRIM FLANGES. LEVEL 4 IS THE ARCHITECTURAL DOCUMENTS. LAYOUT OF SPRINKLER HEADS SHALL BE ACCORDANCE WITH THE SOILS REPORT. T-5 - 3x6 COLOR BODY CERAMIC, IC BRITES, ULTRA EXTERIOR: T-5 TO 9'-4"THEN PAINTED GYP. BOARD SCRATCH COAT: 1 BAG PORTLAND CEMENT, 3/4 TO 1 BAG THE STANDARD FOR ALL EXPOSED AREAS, EXCEPT THOSE INDICATED BELOW SUBMITTED TO THE ARCHITECT FOR REVISION. FIRE SPRINKLER PLANS AND WHITE ABOVE. (SEE INTERIOR ELEVATIONS FOR LOCATION OF LIME TO 6 CU. FT. SAND. FOR LEVEL 5. CALCULATIONS SHALL BE SUBMITTED TO THE BUILDING DEPARTMENT FOR THE UTILITY TRENCHES HAVE BEEN PROPERLY BACKFILLED AND - PATTERN: RUNNING BOND WALL TILES T-5) BROWN COAT: 1 BAG PORTLAND CEMENT, 1 BAG LIME, 6 TO LEVEL 5: EMBED TAPE AND APPLY SEPARATE FIRST, FILL, AND FINISH COATS JURRISDICTIONS HAVING AUTHORITY PRIOR TO INSTALLATION.AUTOMATIC COMPACTED. - GROUT LINE: 1/8" 7 CU. FT. SAND. OF JOINT COMPOUND TO TAPE, FASTENERS, AND TRIM FLANGES, AND APPLY FIRE SPRINKLER SYSTEM SHALL BE DESIGNED AND INSTALLED IN -THINSET: VERSABOND WHITE THINSET, 50 LB FINISH COAT: 1 BAG PORTLAND CEMENT, 2 BAGS LIME, 7 SKIM COAT OF JOINT COMPOUND OVER ENTIRE SURFACE. USE THIS FINISH ACCORDANCE WITH NFPA 13D AS A MINUMUM THE FOUNDATION EXCAVATIONS, FORMING, FOOTING AND PIER DEPTHS, BAG TO 10 CU. FT. SAND. SEE DRAWINGS FOR LEVEL IN AREAS AS FOLLOWS: AND REINFORCEMENT COMPLY WITH THE SOILS REPORT ANDAPPROVED - GROUT: POLYBLEND DRY GROUT UNSANDED, LOCATION OF CEMENT PLASTER FINISH COAT. RECEIVING GLOSS OR SEMI-GLOSS CONDITIONS. PLANS. WHITE, 25 LB BAG CORNER GUARDS• MAXIMUM SLUMP: 2-1/2 IN. USING SLUMP TEST ASTM C 143, MODIFIED AREAS SUBJECT TO SEVERE LIGHTING CONDITIONS. - PROVIDE BULLNOSE TILE EDGE AS SPECIFIED ON 1. CORNER GUARD: ELEVATIONS. SLUMP CONE 2 IN. X 4 IN. X 6 IN. WALL METAL LATH: AT VERTICAL AREAS SCHEDULED TO RECEIVE SPECIAL DRY-ERASE MARKER PAINT. DIVISION 22 - PLUMBING GENERAL REQUIREMENTS CG-1 SURFACE: NO. 17 GAUGE GALVANIZED STUCCO NETTING MEETING AREAS SCHEDULED TO RECEIVE FILM-APPLIED OR PAINTED WALL THE SITE PLAN IS NOT A SURVEY. IT IS BASED ON SITE INFORMATION FEDERAL SPECIFICATION QQ-L-101WITH TWO HORIZONTAL NO. 19 GAUGE 2. CLEANING PRODUCTS FILA-DETERDEK 5 LITER (INITIAL -GENERAL: USED WITH FRP-1 GRAPHICS. SEE PLUMBING DRAWINGS FOR SPECIFIC INFORMATION RELATED TO PROVIDED BY THE OWNER AND IS FOR BUILDING AND SITE WORK LAYOUT GALVANIZED WIRES AT 6 INCHES O.C. OVER TWO LAYERS OF GRADE 'D' CLEANING BY GC) - MANUFACTURER: MARLITE ALL CURVED WORK PLUMBING REQUIREMENTS ONLY. THE CONTRACTOR SHALL VERIFY ON SITE ALL GRADES, SOIL - MODEL: 'FRP' CORNER GUARDS AND MOLDING PAPER (60 MIN.). SEE DIVISION 07. ALL EXPOSED GYPSUM BOARD AT PUBLIC DINING AREAS CONDITIONS, GROUND WATER, EXISTING IMPROVEMENTS, PROPERTY -SIZE: 1-1/2"x 1-1/2"x 120" • LATH AT HORIZONTAL SOFFIT: GALVANIZED MESH, 3.4 LBS/SQ. YD. OVER LINES, EASEMENTS, SETBACKS, UTILITIES AND SUBSTRUCTURES. WHERE 3. FLOOR LEVELING COMPOUND: HYDROMENT/ BOSTIK 1 LAYER OF GRADED' PAPER (60 MIN.). STAPLES: 14 GAUGE WIRE SL150, SELF LEVELING BOSTIK UNIVERSAL PRIMER (USED -COLOR P-100 (WHITE) CONSULTANT DIVISION 23 - HEATING, VENTILATION, & AIR CONDITIONING DISCREPANCIES WITH THE DRAWINGS OCCUR, CONTACT ARCHITECT. WITH SL 150) - PROVIDE FULL HEIGHT CORNER GUARDS AND 'T' STAPLES, DIVERGENT POINTS, 3/4 INCH CROWN, LIN. LEGS. NAILS (IF FIELD SAMPLE: A SAMPLE PANEL SHALL BE PREPARED APPROXIMATELY 2 FEET GRADE SURFACE OF FILL UNDER CONCRETE SLABS SHALL BE SMOOTH MOLDING SOFFIT SUPPORTED BY WOOD FRAMING): 1 3/4 INCH 11 GAUGE, 3/8" BY 2 FEET. THIS SAMPLE PANEL WILL BE A SEPARATE PART OF THE PROJECT. SEE MECHANICAL DRAWINGS FOR SPECIFIC INFORMATION RELATED TO AND EVEN, FREE OF VOIDS,COMPACTED AS SPECIFIED AND TO REQUIRED -AT ALL OUTSIDE CORNERS AND JOINTS. TRIM 'T' HEAD, 3/4"WASHER. STUCCO ACCESSORIES SHALL MEET OR EXCEED ALL PRE-PACKAGED THIN SET MORTAR IS FORMULATED INSTALLATION SHALL NOT PROCEED UNTIL THE ARCHITECT AND OWNER HEATING, VENTILATION &AIR CONDITIONING REQUIREMENTS. ELEVATION. MOLDING AND CORNER GUARDS FLUSH AT TOP THE CIRTERIA OF ASTM C 1063 ACCEPT THE SAMPLE PANEL. THE SAMPLE SHALL SHOW COLOR, TEXTURE, TO MEET INDUSTRY REQUIREMENTS OF ANSI AND TCNA TO PROPERLY PERFORM IN SPECIFIC TYPES OF OF WALL BASE. AND WORKMANSHIP OF FINISHED WORK. WAV CEMENT PLASTER, GENERAL: AT RAISED FOUNDATIONS, PAD GRADE UNDER BUILDING SHALL HAVE INSTALLATION. BLENDING OF STANDARD THIN SET -APPLIED WITH TITEBOND ADVANCED POLYMER DIVISION 24 - UNASSIGNED POSITIVE SLOPE TO A PERFORATED DRAIN SET IN GRAVEL TRENCH. FRP ADHESIVE • INSTALLATION SHALL COMPLY WITH CBC 2510.3 OR CRC 703.7. MORTAR WITH RAPID SETTING MORTAR WILL AFFECT CG-2 • CONTROL JOINTS SHALL BE INSTALLED PER ASTM C 1063: EXTEND PIPE TO ALL PORTIONS OF UNDER FLOOR AREA. THE DRAIN SHALL DISCHARGE INTO THE STREET OR APPROVED DRAINAGE FACILITY. SHRINKAGE AND ULTIMATE STRENGTH OF THE MORTAR. NO LENGTH SHOULD BE GREATER THAN 18 FT. IN EITHER THIS SECTION IS NOT USED CUSTOM BUILDING PRODUCTS WILL NOT WARRANT JOBS -GENERAL: PROVIDED BY GC DIRECTION TILE AND STONE SETTING MATERIAL AND ACCESSORIES: UNLESS OTHERWISE DETAILED OR NOTED, A PERFORATED DRAIN SET INA WHERE THIN SET MORTARS HAVE BEEN MODIFIED WITH - MANUFACTURER: SCHLUTER NO PANEL SHOULD EXCEED 144 SQ. FT. FOR VERTICAL UNAUTHORIZED MATERIALS; WHICH INCLUDES BLEND - MODEL: RONDEC �� GRAVEL TRENCH SHALL BE INSTALLED AROUND THE ENTIRE PERIMETER OF APPLICATIONS 1.3 REFERENCES DIVISION 25 - INTEGRATED AUTOMATION WITH OTHER CUSTOM BUILDING PRODUCTS THIN SET - FINISH: SATIN ANODIZED ALUMINUM, RO 125 AE NO PANEL SHOULD EXCEED 100 SQ. FT. FOR HORIZONTAL, A. ANSI A108 SERIES/A118 SERIES-AMERICAN NATIONAL STANDARDS FOR THE FOUNDATION. THE DRAIN SHALL DISCHARGE INTO THE STREET OR MORTARDS. TILES TO BE BACK BUTTERED. -SIZE: 1/2" CURVED, OR ANGULAR SECTIONS INSTALLATION OF CERAMIC TILE. THIS SECTION IS NOT USED APPROVED DRAINAGE FACILITY. USE ONLY RIGID PIPE, FLEXIBLE PIPE WILL - INSTALLED PER MANUFACTURERS NO LENGTH-TO-WIDTH RATIO SHOULD EXCEED 2 '/2 TO 1 IN ANY GIVEN B. ANSI A136.1 -AMERICAN NATIONAL STANDARD FOR ORGANIC ADHESIVES NOT BE ALLOWED. RECOMMENDATIONS PANEL. FOR INSTALLATION OF CERAMIC TILE. DIVISION 26 - ELECTRICAL IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO TAKE PROPER - 1/2" SIZE FOR T-1/T-2 CORNERS ONLY. GC TO C. ASTM C 144-STANDARD SPECIFICATION FOR AGGREGATE FOR MASONRY SEALED CONCRETE SLAB COORDINATE CORNER SPEC FOR OTHER WALL • EROSION CONTROL MEASURES. THE CONTRACTOR SHALL BE FINISH CONDITIONS. FINISH TEXTURE AND COLOR SHALL BE AS APPROVED BY OWNER. MORTAR. SEE ELECTRICAL DRAWINGS FOR SPECIFIC INFORMATION RELATED TO RESPONSIBLE FOR PROPER SURFACE AND SUBSURFACE DRAINAGE OF • CLIMATE CONDITIONS: AIR TEMPERATURE MUST BE 40°F. MINIMUM AND D. ASTM C 150-STANDARD SPECIFICATION FOR PORTLAND CEMENT. ELECTRICAL REQUIREMENTS. THE SITE. SLOPE ALL FINISH GRADING AWAY FROM BUILDINGS, WALKS, "SALT& PEPPER" FINISH. REFERENCE SPECIFICATION RISING WHEN APPLYING CEMENT PLASTER OR EXTERIOR FINISH COAT. E. TCNA-TILE COUNCIL OF NORTH AMERICA, INC. HANDBOOK FOR CERAMIC, DRIVES OR DECKS AND PROVIDE CATCH BASINS WHERE REQUIRED. SECTIONS 033000 CAST-IN-PLACE CONCRETE AND 033536 7-11 #1043581 AIR TEMPERATURE MUST REMAIN ABOVE 40'F. FOR A MINIMUM OF 24 GLASS, AND STONE TILE INSTALLATION - LATEST EDITION 1. POLISHED CONCRETE FLOOR FINISH, BOTH PROVIDED BY WALL TILE EDGE HOURS. CONSULT NATIONAL WEATHER SERVICE BEFORE BEGINNING F. ISO 13007-INTERNATIONAL STANDARDS ORGANIZATION; CLASSIFICATION DIVISION 27 - COMMUNICATIONS FINISH GRADES SHALL BE HELD DOWN IN PLANTING AREAS. THE 7-ELEVEN AND DATED 02-26-2018 WORK. PROTECT CEMENT PLASTER AND EXTERIOR FINISH COAT FROM FOR GROUT AND ADHESIVES. CONTRACTOR SHALL PROVIDE AND INSTALL A 6" MINIMUM THICKNESS OF 1. INSTALLED PER MANUFACTURERS RECOMMENDATIONS UNEVEN AND EXCESSIVE EVAPORATION DURING HOT, DRY WEATHER. THIS SECTION IS NOT USED CLEAN SELECT TOP SOILS IN THESE AREAS. 2. TILE EDGE: • ALLOWABLE TOLERANCES: MAXIMUM DEVIATION FROM TRUE PLAN 1/8 1.4 SUBMITTALS TE-1 : INCH IN 10 FEET AS MEASURED BY STRAIGHT EDGE PLACED AT ANY A. SUBMIT UNDER PROVISIONS OF SECTION 01300. ROUGH GRADING FOR SLABS-ON-GRADE SHALL BE WITHIN 2/10TH OF ONE BASE -GENERAL: PROVIDED BY GC (USED WITH T-5) LOCATION ON SURFACE. B. PRODUCT DATA: MANUFACTURER'S TECHNICAL INFORMATION FOR EACH - MANUFACTURER: SCHLUTER • FIELD SAMPLE: A SAMPLE PANEL SHALL BE PREPARED APPROXIMATELY PRODUCT SPECIFIED. DIVISION 2H - ELECTRONIC SAFETY AND SECURITY FOOT, PLUS OR MINUS. - MODEL: SCHIENE E 80 EB 2 FEET BY 2 FEET. THIS SAMPLE PANEL WILL BE A SEPARATE PART OF C. SAMPLES: COLOR CHARTS FOR SELECTION OF GROUT. THIS SECTION IS NOT USED 1. VINYL BASE: "WITH 3/8" RADIUS • SITE GRADING SHALL BE WITHIN 5/10TH OF ONE FOOT, PLUS OR MINUS. B-1 -. ROPPE -4" &6"; COLOR"193 BLACK BROWN" - FINISH: BRUSHED STAINLESS STEEL 304 THE PROJECT. INSTALLATION SHALL NOT PROCEED UNTIL THE SAMPLE D. INSTALLATION INSTRUCTIONS: MANUFACTURERS PRINTED INSTRUCTIONS (USE ONLY 6" IF REQUIRED BY LOCAL CODE) -SIZE 5/16" DEEP; 118" HIGH PANEL IS ACCEPTED BY THE ARCHITECT AND OWNER. THE SAMPLE FOR EACH PRODUCT. TE-2 : ALL ROOF DRAINAGE SHALL BE PIPED IN A CLOSED PIPE SYSTEM TO SHALL SHOW COLOR, TEXTURE, AND WORKMANSHIP OF FINISHED WORK. - GENERAL: PROVIDED BY GC (USED WITH T-5 AT DIVISION 29-30 - UNASSIGNED STREET OR APPROVED DRAINAGE FACILITY(U.O.N.). 2. TILE BASE: THE SAMPLE PANEL SHALL REMAIN ON THE PROJECT FOR COMPARISON 1.5 DELIVERY, STORAGE AND HANDLING B-2 : SCHLUTER-AHKA(FOR USE WITH CONCRETE VAULT MAN DOOR) LU PURPOSES WITH THE ACTUAL WORK. A. DELIVER AND STORE PACKAGES MATERIALS IN ORIGINAL CONTAINERS WITH THIS SECTION IS NOT USED - MANUFACTURER: SCHLUTER w BUILDER SHALL PROVIDE LANDSCAPE DEVELOPMENT GUIDELINES TO FLOOR) • OTHER MATERIALS WHERE APPLICABLE: SEALS UNBROKEN AND LABELS INTACT UNTIL TIME OF USE. PREVENT - MODEL: SCHIENE STEP V/SS 60 EB II BUYER THAT SHALL INCLUDE INFORMATION ON SITE MAINTENANCE AND - 3/8" COVE BASE POLYSTYRENE BOARD AND ARCHITECTURAL MOLDINGS: ASTM C-578 DAMAGE OR CONTAMINATION TO MATERIALS BY WATER, FREEZING, - FINISH: BRUSHED STAINLESS STEEL 304 O DEVELOPMENT AND STATE SUCH ITEMS AS "IRRIGATION SYSTEM SHALL BE - 1x6 CORNER TYPE 1. NOMINAL 1 LB/C.F. CURED EXPANDED POLYSTYRENE. FLAME FOREIGN MATTER OR OTHER CAUSES. DESIGNED TO PREVENT SATURATION OF SOIL ADJACENT TO BUILDING". - 1x6 OUTSIDE CORNER -SIZE 5/16" DEEP; 118" HIGH SPREAD AND SMOKE DEVELOPMENT EQUAL TO OR LESS THAN 24 B. DO NOT USE FROZEN MATERIALS UNLESS SPECIFICALLY ALLOWED BY -AHKA 125 AE FOR T-1 AND T-2, AHKA 80 AE FOR V r ) U) AND 450 RESPECTIVELY PER ASTM E-84/UL LISTED. INSULATION MANUFACTURER. ALL UTILITIES UNLESS INDICATED OTHERWISE SHALL BE INSTALLED UNDER T-5 J BOARD SHALL CARRY THE SEAL OF THE RADCO TESTING AGENCY. C. DELIVER AND STORE MATERIALS ON SITE AT LEAST 24 HOURS BEFORE ROLL-A-SHADE WINDOW GLARE PROTECTION Z FABRIC: A BALANCED, OPEN WEAVE, GLASS FIBER FABRIC, COMPLYING WORK BEGINS. GROUND. THE CONTRACTOR SHALL BE RESPONSIBLE TO INSURE THAT ALL J WITH ASTM D1682, STANDARD MESH, AS RECOMMENDED FOR WRAPPING D. PROVIDE HEATED AND DRY STORAGE FACILITIES ON SITE. TRENCHING WITHIN BUILDING AREA SHALL BE BACKFILLED AND 3. GALVINIZ COVE BASE: WITH RADIUS 1. INSIDE MOUNT IS STANDARD. OUTSIDE MOUNT ONLY IF COMPACTED WITH STRUCTURAL SOILS MATERIAL FREE OF ANY ROCKS OR B-5 : SMOOTH PEBBLE TEXTURREE 4" COVE BASE CC .. POLYSTYRENE BOARD AND MOLDINGS. PRIMER/ADHESIVE MIXTURE: INSIDE MOUNT IS DISRUPTED BY SIGNAGE, ETC. G z OTHER SHARP OBJECTS WHICH MAY DAMAGE UNDERGROUND UTILITIES. AROUND INTERIOR PERIMETER OF WALK-IN A FIELD-MIXED BLEND OF STANDARD POLYMER-BASED PRIMER ADHESIVE 1.6 PROJECT CONDITIONS 2. FABRIC WILL BE MERMET 7510 CHARCOAL COCOA 10% AND PORTLAND CEMENT. FOR USE AS A PRIMER AND LEVELER OVER A. MAINTAIN ENVIRONMENTAL CONDITIONS AND PROTECT WORK DURING ANDCOOLER UNITS WITH BRONZE 3"TOP FASCIA AND STAINLESS STEEL w O • UNDERGROUND PIPING SHALL BE LAID TO A MINIMUM 24" DEPTH BELOW CEMENT PLASTER BROWN COAT AND FOR USE AS AN ADHESIVE FOR AFTER INSTALLATION TO COMPLY WITH REFERENCED STANDARDS AND CHAIN - BRONZE CHILD SAFETY TENSION DEVICE. FINISHED GRADE. WHEN UTILITIES ARE PLACED IN A COMMON TRENCH, NOTE: z 06 FABRIC AND POLYSTYRENE BOARD AND MOLDINGS. ACRYLIC RESIN MANUFACTURER'S PRINTED RECOMMENDATIONS. 3. ROLL-A-SHADE TECHS WILL MEASURE AND INSTALL. ALL UTILITIES SHALL MAINTAIN SEPARATIONS AND COVERAGE BOTH 1. VERIFY AHJ SCHLUTER COVER TRANSITION IS BONDING AGENT: BONSEL, TAMMSWAY, OR APPROVED EQUAL. FOR B. VENT TEMPORARY HEATERS TO EXTERIOR TO PREVENT DAMAGE TO VERTICALLY AND HORIZONTALLY, AS REQUIRED BY APPLICABLE CODES. ALLOWED, USE CERAMIC COVE BASE AS REQUIRED CONTACT: JENEVIE ABOUBAKARE > U USE ON CONCRETE OR MASONRY BEFORE APPLICATION OF CEMENT TILEWORK FROM CARBON DIOXIDE. TEL. (951)245-5077 x141 Q PLASTER. C. MAINTAIN TEMPERATURES AT NOT LESS THAN 50 DEG F (10 DEG C) IN TILED BY AHJ T BE APPROVED E ( 7-ELEVEN). JENEVIE.ABOUBARKARE@ROLLASHADE.COM O N ADD MIXTURES: NO ADD MIXTURES OR PLASTIC CEMENTS WILL BE AREAS DURING INSTALLATION AND FOR 7 DAYS AFTER COMPLETION, 2. VERIFY WITH AHJ VINYL BASE (B-1) IS ALLOWED, USE ALLOWED WITHOUT APPROVAL OF THE ARCHITECT. UNLESS HIGHER TEMPERATURES ARE REQUIRED BY REFERENCED ALT BASE AS REQUIRED BY AHJ. TOILER PAPER DISPENSER V z U) SYNTHETIC EXTERIOR FINISH COATING: A 100% PURE ACRYLIC RESIN INSTALLATION STANDARDS OR MANUFACTURER'S WRITTEN INSTRUCTIONS. 06 O BASED, TEXTURED, FACTORY-MIXED COATING HAVING INTEGRAL B-2892 SURFACE MOUNTED TWIN JUMBO TOILET TISSUE COLOR, FOR EXTERIOR USE. MINIMUM STANDARDS SHALL BE DRY-VIT DISPENSER O J SYSTEMS INC., OR APPROVED EQUAL. RETAIL INFORMATION SYSTEM (RIS) BACKBOARD • CURING: WET BASE AS NECESSARY BEFORE APPLICATION WITH FINE FOG PAINTING COUNTERTOPS SPRAY TO PRODUCE UNIFORM MOIST CONDITION. WHEN REQUIRED, 1. BACKBOARD SHALL BE BY U-TECK, MODEL 501082J-FRG APPLY BOND COAT TO CONCRETE BASE AND MOIST CURE FOR MINIMUM APPLICATION SYSTEMS AND MATERIALS SHALL COMPLY TO THE P.D.C.A. CONTACT: DEBRA WOLFE 1.AT POINT OF SALE LOCATIONS z OF 24 HOURS BEFORE APPLYING FIRST COAT OF CEMENT PLASTER. "ARCHITECTURAL SPECIFICATIONS MANUAL." TEL. (800)542-7011 -WILSONART COSMIC STRANDZ DO NOT APPLY BROWN COAT SOONER THAN 48 HOURS AFTER - MATTE FINISH 4941K-60 APPLICATION OF SCRATCH COAT. PAINTING SHALL BE INCLUDED, BUT NOT LIMITED TO THE FOLLOWING 2.AT COFFEE CAR LOCATION DO NOT APPLY CEMENT PLASTER FINISH COAT SOONER THAN 14 DAYS (U.O.N.): METAL STUDS -SILESTONE ALPINA WHITE AFTER APPLICATION OF BROWN COAT. ALL EXPOSED METAL. THIS INCLUDES FLASHING, SCUPPERS, GUTTERS, 3. AT BEVERAGE BAR AND FRONT COUNTER HOT FOOD INSPECT AND REPAIR BASE COATS BEFORE APPLICATION OF FINISH DOWNSPOUTS, LOUVERS, GATES, RAILINGS, ETC. SHEET METAL ROOF 1. CLARKDIETRICH METAL FRAMING SECTION COAT. VALLEYS, ROOF FLASHINGS AND VALLEYS SHALL BE PAINTED TO MATCH ICC#- ESR 1166P -STAINLESS STEEL CURE BASE COATS MINIMUM OF 48 HOURS AFTER APPLICATION. ROOFING MATERIAL. IAPMO#- ES-0189 MAINTAIN MOIST CONDITIONS BY FINE FOG SPRAY. ALL EXPOSED EXTERIOR WOOD SHALL BE PAINTED AND BACK PRIMED. CURE FINISH COAT FOR MINIMUM OF 7 DAYS. ALL PRECAST EXPOSED CONCRETE SHALL BE SEALED. • INSTALLATION AND FINISHING OF GYPSUM WALL BOARD SHALL COMPLY ALL DOORS AND FRAMES SHALL BE PAINTED, AFTER BEING HUNG AND FITTED, DOORS SHALL BE PAINTED ON ALL SIX SIDES. ALL GYPSUM WITH GA-216. BOARD SHALL BE PAINTED EXCEPT IN MECHANICAL CLOSETS. • FIRE-RESISTANCE RATINGS: WHERE GYPSUM WALLBOARD SYSTEMS ALL GYPSUM BOARD RECEIVING WALL COVERING SHALL BE PRIMED. ALL WITH FIRE-RESISTANCE RATINGS ARE INDICATED. EXPOSED INTERIOR WOOD SHALL BE PAINTED, INCLUDING CASEWORK WHERE INDICATED. PR#2 01 .06.2020 • ALLOWABLE TOLERANCES: GYPSUM WALLBOARD SURFACES SHALL HAVE SURFACES NOT TO BE PAINTED SHALL INCLUDE THE FOLLOWING (U.O.N.): NO MEASURABLE VARIATION IN ANY 2-FOOT DIRECTION AND A MAXIMUM PRE-FINISHED MATERIALS SUCH AS ACOUSTIC CEILING BOARD, BAKED VARIATION OF 1/8-INCH IN 10-FEET. SHIM WORK AS REQUIRED TO AND PORCELAIN ENAMEL, PLATED METALS, LAMINATED PLASTICS, COMPLY WITH SPECIFIED TOLERANCES. VINYLS, ETC. • FIRE-RATED GYPSUM WALLBOARD: ASTM C36, TYPE X, 5/8-INCH THICK, STAINLESS STEEL, BRONZE, AND ALUMINUM. REVISIONS WITH TAPERED AND WRAPPED LONG EDGES. DO NOT PAINT ANY MOVING PARTS OR OPERATING UNITS, MECHANICAL AND ELECTRICAL PARTS, SUCH AS VALVE AND DAMPER OPERATORS, • FIRE RATED WALLS, THROUGH PENETRATION FIRESTOP SYSTEMS & FIRE LINKAGES, SENSING DEVICES, MOTOR AND FAN SHAFTS. RESISTIVE JOINT SYSTEMS TO BE CONSTRUCTED IN ACCORDANCE WITH DO NOT PAINT OVER ANY CODE-REQUIRED LABELS, SUCH AS ASSEMBLIES LISTED BY UL, WARNOCK HERSEY/INTERTEK/ETL/SEMKO. UNDERWRITERS LABORATORIES AND FACTORY MUTUAL, OR ANY EQUIPMENT IDENTIFICATION,PERFORMANCE RATING, NAME, OR NOMENCLATURE PLATES. NEATLY MASK ALL SUCH ITEMS, AND REMOVE STANDARDS: INSTALLATION STANDARDS: ASTM C 840/GA 216/ASTM C 919. MASKING AT COMPLETION OF PAINTING. • ASTM C-11 FOR DEFINITIONS UNLESS OTHERWISE SCHEDULED, THE OWNER SHALL SELECT PAINT • ASTM C-754 GENERAL COMPONENTS. COLORS. • ANSI 118.9 CEMENT BACKER BOARD • ASTM C-1047 TRIM PAINT ALL METAL REGISTERS AND GRILLS TO MATCH ADJACENT SURFACES • ASTM C-475 JOINT TREATMENT MATERIALS (U.O.N.). • ALL PERIMETER CONDITIONS WHERE FIRE RATED GYP BOARD PAINT ALL GUTTERS TO MATCH FASCIA AND PAINT ALL DOWNSPOUTS AND ASSEMBLIES MEET OTHER CONSTRUCTION MUST BE CONSTRUCTED VENTS TO MATCH ADJACENT SURFACES (U.O.N.). USING A LISTED FIRE-RESISTIVE JOINT SYSTEM. • ALL PENETRATIONS THROUGH FIRE RATED GYP BOARD ASSEMBLIES MUST BE CONSTRUCTED USING A LISTED THROUGH PENETRATION FIRESTOP SYSTEM. • MOISTURE-RESISTANT GYPSUM BOARD: ASTM C630, TYPE X, 5/8-INCH THICK WITH TAPERED AND WRAPPED LONG EDGES. PROVIDE FOR EXPOSED AND CONCEALED LOCATIONS AT WALLS OF BATHROOMS, KITCHENS, AND OTHER WET SPACES; DO NOT USE ONCEILINGS. • SCREWS: ASTM C954 OR ASTM C1002. • METAL TRIM: PROVIDE SQUARE CORNER BEAD AND EDGE TRIM. • ACOUSTICAL SHEET SEALANT PAD: HARRY A. LOWRY&ASSOCIATES, 11176 PENROSE ST. SUN VALLEY, CALIFORNIA 91352. (818) 768-4661 OR EQUAL. • TEXTURING MATERIAL: U.S. GYPSUM "USG SPRAY TEXTURE FINISH" OR APPROVED EQUAL; MACHINE LIGHT"ORANGE PEEL FINISH". • INSTALLATION OF FASTENERS: FIRE-RATED PARTITIONS: INSTALL FASTENERS IN ACCORDANCE WITH CBC TABLE 721.1 (2) NON-FIRE-RATED PARTITIONS: INSTALL FASTENERS IN ACCORDANCE WITH CBC TABLE 2508.5 FIRE-RATED CEILINGS: INSTALL FASTENERS IN ACCORDANCE WITH CBCTABLE721.1 (3) AND GYPSUM ASSOCIATION "FIRE-RESISTANCE SEAL/SIGNATURE DESIGN MANUAL". NON-FIRE-RATED CEILINGS: INSTALL FASTENERS SPACED NOT MORE JOB NO. 1497.009 THAN 12-INCHES ON CENTER FOR SCREWS.INSTALL SCREWS USING POWERED SCREW GUNS WITH ADJUSTABLE SCREW-DEPTH CONTROL DRAWN WF HEAD. CHECK GM SPECIFICATIONS 0 0 NSHEET 0 N O N CO G002