Laserfiche WebLink
Setup EVR/ISD Setup <br /> Continued from <br /> previous page <br /> Go to a fueling point and dispense <br /> AUTO MAP GRACE-HOSE ❑ DISPENSE NOW 10:00 into approved container,a <br /> $ PRESS<ENTER> —� E PRESS<STEP>TO CANCEL couplele of gallons product from <br /> w <br /> the first hose you want to auto <br /> Note:This step appears only after completing pressing Enter starts a map.NOTE:you must dispense <br /> from all product meters at the site <br /> Fuel Hose Table Setup(see previous page). 10 minute timer br one <br /> auto map dispense. including at least 1 blended <br /> You must repeat this procedure br each product,if available. <br /> product meter. <br /> FP:x GRD:x M:x H:x <br /> H:x FP:x Label x E PRESS<STEP>TO CONTINUE_D <br /> PRESS<ENTER> You have dispensed from a hose <br /> Normal display FP:x M:x Assigned H:x that has already been mapped. <br /> The system will display a <br /> fueling point number,hose You dispensed less than 1/2 gallon(single product <br /> number,and a hose label.If Press TANK/SENSOR until 3 possible Insufficient Data.Retry? minimum),or 1 gallon(blended product minimum). <br /> this identifies the correct the correct FP/hose/label error displ�s NOTE:if mapping dispensing equipment that uses <br /> hose(i.e.,the one used to appears in the display. cumulative numbers,it may require 2 dispenses <br /> dispense product)press from each hose/grade. <br /> ENTER,otherwise press NOTE:if the hose dispensed <br /> Tank/Sensor.NOTE:you from is a non-vapor recovery You cannotmap more than 2 fueling _�a <br /> are looking to identify the hose,select:NON VAPOR AFMx NO Space for FP points(and related hoses)to one AFM aS <br /> selected hose,not the RECO VERY HOSE (only one AFM is installed per dispenser <br /> product dispensed. <br /> FUEL HOSE TABLE SETUP SELECT HOSE <br /> PRESS<ENTER> H:n FP:n Label n <br /> Press button until you see this display. <br /> Go to Edit Fuel Hose X displa y(see <br /> previous page)and reassign correct <br /> AFM for this hose. <br /> S MANUAL MAP GRADE-HOSESELECT PRODUCT <br /> PRESS<ENTER> L01 B03 S01 FPO <br /> 1 M00 P01 <br /> Note:This step appears only after L=Mapped fuel position ince <br /> completing Fuel Hose Table Setup B=Bus identification <br /> (see previous page). S=slot Amber <br /> M =Fuel position reported DIM Press TANK/SENSOR to <br /> M=Meter assign to product scroll through product tatle <br /> P=Product 6r this fuel position indec and find desired product. <br /> $ E ASSIGN HOSE S E <br /> HH:Hose Label <br /> Press TANK/SENSOR to scroll <br /> WIIII through fuel hose table and find <br /> desired label. <br /> S SET ANALYSIS TIMES [E(] SET START TIME ©Enter new F SET POST DELAY OURATION �© Enter new rF <br /> PRESS<ENTER> TIME:11:59 PM start time S DELAY MINUTES: 001 delay L' S <br /> Default time is 11:59 PM. Default is 001,max is 720. <br /> Time defines when 24-hour ISD /Q DO NOT CHANGE <br /> tests are Rin and results posted. S DEFAULT VALUE. <br /> EVR TYPE <br /> S <br /> PRESS<ENTER> B Backup C Change Drier Repress until Key press <br /> desired message 2 <br /> Tank appears <br /> in displaysequence <br /> S❑step T❑Sensor ©Pant PP <br /> isd-evr/isd-evrset I b.eps <br /> Figure 7. EVR/ISD Setup 3 <br /> 10-14 <br /> CARO Approved IOM 10 -Veeder Root ISD Install,Setup,8 Operation Manual-Executive Order VR-202 <br />