|
v
<br /> waw.ww r�.ev....�,.ury.ywronu��unr�uae�ss.sr....yo
<br /> 2016 CALIFORNIA GREEN BUILDING STANDARDS CODE
<br /> NONRESIDENTIAL MANDATORY MEASURES , SHEET 3 (INCLUDING JANUARY 1 , 2017 ERRATA) Drawn: ZERTUCHE
<br /> DRAFTING & DESIGN
<br /> INSPECTOR INSPECTOR INSPECTOR INSPECTOR HORACIO ZERTUCHE
<br /> SIGNOFF SIGNOFF SIGNOFF SIGNOFF 1050 N.CARPENTER,SUITE-J
<br /> MODESTO,CA 95351
<br /> 5.504.4 FINISH MATERIAL POLLUTANT CONTROL. Finish materials shall comply with Sections 5.504.4.1 through Exception: Refrigeration systems containing low-global warming potential (low-GWP)refrigerant with a GWP (209)507-6036
<br /> 5.504.4.6. TABLE 5.504.4.3 - VOC CONTENT LIMITS FOR ARCHITECTURAL TABLE 5.504.4.5 - FORMALDEHYDE LIMITS, value less than 150 are not subject to this section. Low-GWP refrigerants are nonozone-depleting refrigerants horacio@zertuchedrafting.com
<br /> COATINGS2,3 MAXIMUM FORMALDEHYDE EMISSIONS IN PARTS PER MILLION that include ammonia,carbon dioxide(CO2),and potentially other refrigerants.
<br /> 5.504.4.1 Adhesives,sealants and caulks. Adhesives,sealants,and caulks used on the project shall meet GRAMS OF VOC PER LITER OF COATING,LESS WATER&LESS EXEMPT COMPOUNDS
<br /> the requirements of the following standards: PRODUCT CURRENT LIMIT 5.508.2.1 Refrigerant piping. Piping compliant with the California Mechanical Code shall be installed to be
<br /> 1. Adhesives,adhesive bonding primers adhesive primers,sealants,sealant primers and caulks shall COATING CATEGORY CURRENT VOC LIMIT accessible for leak protection and repairs. Piping runs using threaded pipe,copper tubing with an outside
<br /> comply with local or regional air pollution control or air quality management district rules where HARDWOOD PLYWOOD VENEER CORE 0.05 diameter(OD)less than 1/4 inch,flared tubing connections and short radius elbows shall not be used in
<br /> applicable,or SCAQMD Rule 1168 VOC limits,as shown in Tables 5.504.4.1 and 5.504.4.2.Such FLAT COATINGS 50 refrigerant systems except as noted below.
<br /> products also shall comply with the Rule 1168 prohibition on the use of certain toxic compounds HARDWOOD PLYWOOD COMPOSITE CORE 0.05
<br /> (chloroform,ethylene dichloride, methylene chloride, perch loroethylene and trichloroethylene),except for NONFLAT COATINGS 100 5.508.2.1.1 Threaded pipe.Threaded connections are permitted at the compressor rack.
<br /> aerosol products as specified in subsection 2, below. PARTICLE BOARD 0.09
<br /> NONFLAT HIGH GLOSS COATINGS 150 5.508.2.1.2 Copper pipe.Copper tubing with an OD less than 1/4 inch may be used in systems with a
<br /> 2. Aerosol adhesives,and smaller unit sizes of adhesives,and sealant or caulking compounds(in SPECIALTY COATINGS MEDIUM DENSITY FIBERBOARD 0.11 refrigerant charge of 5 pounds or less. Ln
<br /> units of product, less packaging,which do not weigh more than one pound and do not consist of more THIN MEDIUM DENSITY FIBERBOARD2 0.13
<br /> than 16 fluid ounces)shall comply with statewide VOC standards and other requirements, including ALUMINUM ROOF COATINGS 400 5.508.2.1.2.1 Anchorage.One-fouth-inch OD tubing shall be securely clamped to a rigid base to
<br /> 1. VALUES IN THIS TABLE ARE DERIVED FROM THOSE SPECIFIED BY THE CALIFORNIA AIR RESOURCES BOARD,
<br /> prohibitions on use of certain toxic compounds,of California Code of Regulations,Title 17,commencing AIR TOXICS CONTROL MEASURE FOR COMPOSITE WOOD AS TESTED IN ACCORDANCE WITH ASTM E 1333. FOR keep vibration levels below 8 mils.
<br /> with Section 94507. BASEMENT SPECIALTY COATINGS 400
<br /> ADDITIONAL INFORMATION,SEE CALIFORNIA CODE OF REGULATIONS,TITLE 17,SECTIONS 93120 THROUGH 5.508.2.1.3 Flared tubing connections. Double-flared tubing connections may be used for pressure
<br /> BITUMINOUS ROOF COATINGS 50 93120.12. controls,valve pilot lines and oil.
<br /> BITUMINOUS ROOF PRIMERS 350 2. THIN MEDIUM DENSITY FIBERBOARD HAS A MAXIMUM THICKNESS OF 5/16 INCHES(8 MM). M
<br /> Exception: Single-flared tubing connections may be used with a multiring seal coated with industrial
<br /> TABLE 5.504.4.1 - ADHESIVE VOC LIMIT1,2 BOND BREAKERS 350 O
<br /> 5.504.4.6 Resilient flooring systems. For 80 percent of floor area receiving resilient flooring, installed sealant suitable for use with refrigerants and tightened in accordance with manufacturer's
<br /> Less Water and Less Exempt Compounds in Grams per Liter CONCRETE CURING COMPOUNDS 350
<br /> resilient flooring shall meet at least one of the following: recommendations.
<br /> ARCHITECTURAL APPLICATIONS CURRENT VOC LIMIT CONCRETE/MASONRY SEALERS 100 1. Certified under the Resilient Floor Covering Institute(RFCI)FloorScore program; 5.508.2.1.4 Elbows.Short radius elbows are only permitted where space limitations prohibit use of l J
<br /> 2. Compliant with the VOC-emission limits and testing requirements specified in the California long radius elbows.
<br /> INDOOR CARPET ADHESIVES 50 DRIVEWAY SEALERS 50 Department of Public Health's 2010 Standard Method for the Testing and Evaluation Chambers,
<br /> Version 1.1, February 2010; 5.508.2.2 Valves.Valves Valves and fittings shall comply with the California Mechanical Code and as O
<br /> CARPET PAD ADHESIVES 50 DRY FOG COATINGS 150 3. Compliant with the Collaborative for High Performance Schools California(CA-CHPS)Criteria follows.
<br /> OUTDOOR CARPET ADHESIVES 150 FAUX FINISHING COATINGS 350 Interpretation for EQ 7.and EQ 7.1 (formerly EQ 2.2)dated July 2012 and listed in the CHPS High
<br /> Performance Product DataBase;or 5.508.2.2.1 Pressure relief valves. For vessels containing high-GWP refrigerant,a rupture disc shall
<br /> WOOD FLOORING ADHESIVES 100 FIRE RESISTIVE COATINGS 350 4. Products certified under UL GREENGUARD Gold (formerly the Greenguard Children's&Schools be installed between the outlet of the vessel and the inlet of the pressure relief valve. z
<br /> a
<br /> RUBBER FLOOR ADHESIVES 60 FLOOR COATINGS 100 Program). 5.508.2.2.1.1 Pressure detection.A pressure gauge, pressure transducer or other device shall
<br /> 5.504.4.6.1 Verification of compliance. Documentation shall be provided verifying that resilient flooring be installed in the space between the rupture disc and the relief valve inlet to indicate a disc
<br /> SUBFLOOR ADHESIVES 50 FORM-RELEASE COMPOUNDS 250
<br /> materials meet the pollutant emission limits. rupture or discharge of the relief valve.
<br /> CERAMIC TILE ADHESIVES 65 GRAPHIC ARTS COATINGS(SIGN PAINTS) 500
<br /> 5.504.5.3 Filters. In mechanically ventilated buildings, provide regularly occupied areas of the building with air 5.508.2.2.2 Access valves.Only Schrader access valves with a brass or steel body are
<br /> VCT&ASPHALT TILE ADHESIVES 50 HIGH-TEMPERATURE COATINGS 420 filtration media for outside and return air that provides at least a Minimum Efficiency Reporting Value(MERV)of permitted for use.
<br /> 8. MERV 8 filters shall be installed prior to occupancy,and recommendations for maintenance with filters of the
<br /> DRYWALL&PANEL ADHESIVES 50 INDUSTRIAL MAINTENANCE COATINGS 250 same value shall be included in the operation and maintenance manual. 5.508.2.2.2.1 Valve caps. For systems with a refrigerant charge of 5 pounds or more,valve caps
<br /> COVE BASE ADHESIVES 50 LOW SOLIDS COATINGS, 120 Exceptions: shall be brass or steel and not plastic.
<br /> MULTIPURPOSE CONSTRUCTION ADHESIVES 70 MAGNESITE CEMENT COATINGS 450 5.508.2.2.2.2 Seal caps. If designed for it,the cap shall have a neoprene O-ring in place.
<br /> 1. An ASHRAE 10%to 15%efficiency filter shall be permitted for an HVAC unit meeting the 2013
<br /> STRUCTURAL GLAZING ADHESIVES 100 MASTIC TEXTURE COATINGS 100 California Energy Code having 60,000 Btu/h or less capacity per fan coil, if the energy use of the air 5.508.2.2.2.2.1 Chain tethers.Chain tethers to fit ovr the stem are required for valves
<br /> delivery system is 0.4 W/cfm or less at design air flow. designed to have seal caps.
<br /> SINGLE-PLY ROOF MEMBRANE ADHESIVES 250 METALLIC PIGMENTED COATINGS 5002. Existing mechanical equipment. Q
<br /> OTHER ADHESIVES NOT SPECIFICALLY LISTED 50 Exception:Valves with seal caps that are not removed from the valve during stem operation. Z
<br /> MULTICOLOR COATINGS 250 0
<br /> 5.504.7 ENVIRONMENTAL TOBACCO SMOKE(ETS)CONTROL. Where outdoor areas are provided for smoking, 0
<br /> SPECIALTY APPLICATIONS PRETREATMENT WASH PRIMERS 420 prohibit smoking within 25 feet of building entries,outdoor air intakes and operable windows and within the building as 5.508.2.3 Refrigerated service cases. Refrigerated service cases holding food products containing vinegar and 0 It
<br /> already prohibited by other laws or regulations;or as enforced by ordinances, regulations or policies of any city, salt shall have evaporator coils of corrosion-reistant material,such as stainless steel;or be coated to prevent 0
<br /> PVC WELDING 510 PRIMERS, SEALERS,&UNDERCOATERS 100 county,city and county, California Community College,campus of the California State University,or campus of the corrosion from these substances. ui a
<br /> University of California,whichever are more stringent.When ordinances, regulations or policies are not in place, post
<br /> CPVC WELDING 490 REACTIVE PENETRATING SEALERS 350 signage to inform building occupants of the prohibitions. 5.508.2.3.1 Coil coating.Consideration shall be given to the heat transfer efficiency of coil coating to
<br /> ABS WELDING 325maximize energy efficiency. Q
<br /> RECYCLED COATINGS 250
<br /> SECTION 5.505 INDOOR MOISTURE CONTROL
<br /> PLASTIC CEMENT WELDING 250 ROOF COATINGS 50 5.505.1 INDOOR MOISTURE CONTROL. Buildings shall meet or exceed the provisions of California Building Code, 5.508.2.4 Refrigerant receivers. Refrigerant receivers with capacities greater than 200 pounds shall be fitted 0,_,
<br /> with a device tha indicates the level of refrigerant in the receiver. � ( ) O
<br /> CCR,Title 24, Part 2,Sections 1203(Ventilation)and Chapter 14(Exterior Walls). For additional measures not �
<br /> ADHESIVE PRIMER FOR PLASTIC 550 RUST PREVENTATIVE COATINGS 250p�
<br /> applicable to low-rise residential occupancies,see Section 5.407.2 of this code. LLI 0f = N
<br /> CONTACT ADHESIVE 80 5.508.2.5 Pressure testing.The system shall be pressure tested during installation prior to evacuation and > LuSHELLACS: charging.char LLI L U Ln
<br /> SECTION 5.506 INDOOR AIR QUALITY = j 0')
<br /> SPECIAL PURPOSE CONTACT ADHESIVE 250 CLEAR 730 5.506.1 OUTSIDE AIR DELIVERY. For mechanically or naturally ventilated spaces in buildings, meet the minimum 5.508.2.5.1 Minimum pressure.The system shall be charged with regulated dry nitrogen and (-) = O Q
<br /> STRUCTURAL WOOD MEMBER ADHESIVE 140 requirements of Section 120.1 (Requirements For Ventilation)of the California Energy Code,or the applicable local appropriate tracer as to bring system pressure u to 300 si minimum. LLJ = U
<br /> OPAQUE 550 p g g Y p p p g LU U
<br /> code,whichever is more stringent,and Division 1,Chapter 4 of CCR, Title 8. W �-. _-
<br /> TOP&TRIM ADHESIVE 250 SPECIALTY PRIMERS, SEALERS&UNDERCOATERS 100 5.508.2.5.2 Leaks.Check the system for leaks,repair any leaks,and retest for pressure using the same U') 0
<br /> 5.506.2 CARBON DIOXIDE(CO2)MONITORING. For buildings or additions equipped with demand control gauge. ~ z T_ U7 O
<br /> SUBSTRATE SPECIFIC APPLICATIONS ventilation, CO2 sensors and ventilation controls shall be specified and installed in accordance with the requirements 07 Z J
<br /> STAINS 250 of the California Energy Code, Section 120(c)(4). 5.508.2.5.3 Allowable pressure change.The system shall stand, unaltered,for 24 hours with no more 0 >-
<br /> METAL TO METAL 30 Q J N
<br /> STONE CONSOLIDANTS 450 than a+/-one pound pressure change from 300 sig' measured with the same gauge.
<br /> wLL UJ
<br /> PLASTIC FOAMS 50 SECTION 5.507 ENVIRONMENTAL COMFORT Z o
<br /> SWIMMING POOL COATINGS 340 5.507.4 ACOUSTICAL CONTROL. Employ building assemblies and components with Sound Transmission Class 5.508.2.6 Evacuation.The system shall be evacuated after pressure testing and prior to charging. o °a
<br /> POROUS MATERIAL(EXCEPT WOOD) 50 (STC)values determined in accordance with ASTM E 90 and ASTM E 413,or Outdoor-Indoor Sound Transmission
<br /> TRAFFIC MARKING COATINGS 100 Class(OITC)determined in accordance with ASTM E 1332, using either the prescriptive or performance method in 5.508.2.6.1 First vacuum. Pull a system vacuum down to at least 1000 microns(+/-50 microns),and
<br /> WOOD 30 Section 5.507.4.1 or 5.507.4.2.
<br /> TUB&TILE REFINISH COATINGS 420 hold for 30 minutes.
<br /> FIBERGLASS 80 Exception: Buildings with few or no occupants or where occupants are not like) to be affected b exterior
<br /> WATERPROOFING MEMBRANES 250 p g p p y Y 5.508.2.6.2 Second vacuum.Pull a second system vacuum to a minimum of 500 microns and hold for 30
<br /> noise, as determined by the enforcement authority,such as factories, stadiums, storage,enclosed parking minutes.
<br /> WOOD COATINGS 275 structures and utility buildings.
<br /> 1. IF AN ADHESIVE IS USED TO BOND DISSIMILAR SUBSTRATES TOGETHER, 5.508.2.6.3 Third vacuum.Pull a third vacuum down to a minimum of 300 microns,and hold for 24 hours LIJ
<br /> THE ADHESIVE WITH THE HIGHEST VOC CONTENT SHALL BE ALLOWED. WOOD PRESERVATIVES 350 Exception: [DSA-SS] For public schools and community colleges,the requirements of this section and all with a maximum drift of 100 microns over a 24-hour period.
<br /> ZINC-RICH PRIMERS 340 subsections apply only to new construction. U.
<br /> 2. FOR ADDITIONAL INFORMATION REGARDING METHODS TO MEASURE
<br /> THE VOC CONTENT SPECIFIED IN THIS TABLE, SEE SOUTH COAST AIR 1. GRAMS OF VOC PER LITER OF COATING,INCLUDING WATER&EXEMPT COMPOUNDS 5.507.4.1 Exterior noise transmission, prescriptive method. Wall and roof-ceiling assemblies exposed to CHAPTER 7
<br /> the noise source making up the building or addition envelope or altered envelope shall meet a composite STC
<br /> QUALITY MANAGEMENT DISTRICT RULE 1168,
<br /> 2. THE SPECIFIED LIMITS REMAIN IN EFFECT UNLESS REVISED LIMITS ARE LISTED IN SUBSEQUENT COLUMNS IN rating of at least 50 or a composite OITC rating of no less than 40,with exterior windows of a minimum STC of INSTALLER & SPECIAL INSPECTOR QUALIFICATIONS U
<br /> www.arb.ca.gov/DRDB/SC/CURHTML/Rl 168.PDF THE TABLE. 40 or OITC of 30 in the following locations:
<br /> 3. VALUES IN THIS TABLE ARE DERIVED FROM THOSE SPECIFIED BY THE CALIFORNIA AIR RESOURCES BOARD, 702 QUALIFICATIONS
<br /> ARCHITECTURAL COATINGS SUGGESTED CONTROL MEASURE,FEB.1,2008. MORE INFORMATION IS AVAILABLE 1. Within the 65 CNEL noise contour of an airport. Q
<br /> FROM THE AIR RESOURCES BOARD. 702.1 INSTALLER TRAINING. HVAC system installers shall be trained and certified in the proper
<br /> Exceptions: installation of HVAC systems including ducts and equipment by a nationally or regionally recognized training or
<br /> TABLE 5.504.4.2 - SEALANT VOC LIMIT certification program. Uncertified persons may perform HVAC installations when under the direct supervision and
<br /> 5.504.4.3.2 Verification.Verification of compliance with this section shall be provided at the request of a. Ldp or CNEL for military airports shall be determined by the facility Air Installation Compatible responsibility of a person trained and certified to install HVAC systems or contractor licensed to install HVAC systems. Q z
<br /> Less Water and Less Exempt Compounds in Grams per Liter the enforcing agency. Documentation may include, but is not limited to,the following: Land Use Zone(AICUZ)plan. Examples of acceptable HVAC training and certification programs include but are not limited to the following: 7
<br /> 1. Manufacturer's product specification b. Ldp or CNEL for other airports and heliports for which a land use plan has not been developed L
<br /> SEALANTS CURRENT VOC LIMIT 2. Field verification of on-site product containers shall be determined by the local general plan noise element. 1. State certified apprenticeship programs.
<br /> ARCHITECTURAL 250 2. Public utility training programs.
<br /> 5.504.4.4 Carpet Systems.All carpet installed in the building interior shall meet at least one of the testing and 2. Within the 65 CNEL or Ldp noise contour of a freeway or expressway, railroad, industrial source or 3. Training programs sponsored by trade, labor or statewide energy consulting or verification organizations.
<br /> MARINE DECK 760 product requirements: fixed-guideway source as determined by the Noise Element of the General Plan. 4. Programs sponsored by manufacturing organizations. >.
<br /> 5. Other programs acceptable to the enforcing agency.
<br /> NONMEMBRANE ROOF 300 1. Carpet and Rug Institute's Green Label Plus Program. 5.507.4.1.1. Noise exposure where noise contours are not readily available.Buildings exposed to a
<br /> 2. Compliant with the VOC-emission limits and testing requirements specified in the California noise level of 65 dB L 1 hr during an hour of operation shall have building,addition or alteration 702.2 SPECIAL INSPECTION HCD When required b the enforcing agency,the owner or the
<br /> ROADWAY 250 Department of Public Health Standard Method for the Testing and Evaluation of Volatile Organic eq 9 Y p g' ll q Y 9 9 Y. z
<br /> exterior wall and roof-ceiling assemblies exposed to the noise source meeting a composite STC rating of responsible entity acting as the owner's agent shall employ one or more special inspectors to provide inspection or
<br /> SINGLE-PLY ROOF MEMBRANE 450 Chemical Emissions from Indoor Sources Using Environmental Chambers,Version 1.1, February at least 45(or OITC 35) with exterior windows of a minimum STC of 40(or OITC 30). other duties necessary to substantiate compliance with this code. Special inspectors shall demonstrate competence W LLI
<br /> ,2010(also known as CDPH Standard Method V1.1 or Specification 01350). to the satisfaction of the enforcing agency for the particular type of inspection or task to be performed. In addition to
<br /> OTHER 420 3. NSF/ANSI 140 at the Gold level or higher; 5.507.4.2 Performance Method. For buildings located as defined in Section 5.507.4.1 or 5.507.4.1.1,wall and other certifications or qualifications acceptable to the enforcing agency,the following certifications or education may be W
<br /> 4. Scientific Certifications Systems Sustainable Choice; or roof-ceiling assemblies exposed to the noise source making up the building or addition envelope or altered considered by the enforcing agency when evaluating the qualifications of a special inspector:
<br /> SEALANT PRIMERS 5. Compliant with the Collaborative for High Performance Schools California(CA-CHPS)Criteria envelope shall be constructed to provide an interior noise environment attributable to exterior sources that does
<br /> Interpretation for EQ 7.0 and EQ 7.1 (formerly EQ 2.2)dated July 2012 and listed in the CHPS High not exceed an hourly equivalent noise level (Leq-1 Hr)of 50 dBA in occupied areas during any hour of operation. 1. Certification by a national or regional green building program or standard publisher. Q
<br /> ARCHITECTURAL Performance Product Database. r n
<br /> 2. Certification by a statewide energy consulting or verification organization,such as HERS raters, building V
<br /> NONPOROUS 250 5.504.4.4.1 Carpet cushion.All carpet cushion installed in the building interior shall meet the 5.507.4.2.1 Site Features. Exterior features such as sound walls or earth berms may be utilized as performance contractors,and home energy auditors.
<br /> requirements of the Carpet and Rug Institute Green Label program. appropriate to the building,addition or alteration project to mitigate sound migration to the interior. 3. Successful completion of a third party apprentice training program in the appropriate trade.
<br /> POROUS 775 4. Other programs acceptable to the enforcing agency.
<br /> MODIFIED BITUMINOUS 500 5.504.4.4.2 Carpet adhesive.All carpet adhesive shall meet the requirements of Table 5.504.4.1. 5.507.4.2.2 Documentation of Compliance. An acoustical analysis documenting complying interior
<br /> sound levels shall be prepared by personnel approved by the architect or engineer of record. Notes: >_
<br /> MARINE DECK 760 5.504.4.5 Composite wood products. Hardwood plywood, particleboard and medium density fiberboard V M
<br /> composite wood products used on the interior or exterior of the buildings shall meet the requirements for 5.507.4.3 Interior sound transmission. Wall and floor-ceiling assemblies separating tenant spaces and tenant 1. Special inspectors shall be independent entities with no financial interest in the materials or the W
<br /> OTHER 750 formaldehyde as specified in ARB's Air Toxics Control Measure for Composite Wood(17 CCR 93120 et seq.). spaces and public places shall have an STC of at least 40. project they are inspecting for compliance with this code.
<br /> Those materials not exempted under the ATCM must meet the specified emission limits,as shown in Table 2. HERS raters are special inspectors certified by the California Energy Commission (CEC)to rate
<br /> NOTE: FOR ADDITIONAL INFORMATION REGARDING METHODS TO 5.504.4.5. Note: Examples of assemblies and their various STC ratings may be found at the California Office of homes in California according to the Home Energy Rating System(HERS).
<br /> MEASURE THE VOC CONTENT SPECIFIED IN THESE TABLES, SEE SOUTH Noise Control: www.tooIbase.org/PDF/CaseStudies/stc_icc_ratings.pdf.
<br /> COAST AIR QUALITY MANAGEMENT DISTRICT RULE 1168. 5.504.4.5.3 Documentation. Verification of compliance with this section shall be provided as [BSC-CG] When required by the enforcing agency,the owner or the responsible entity acting as the owner's agent w
<br /> requested by the enforcing agency. Documentation shall include at least one of the following: SECTION 5.508 OUTDOOR AIR QUALITY shall employ one or more special inspectors to provide inspection or other duties necessary to substantiate w z
<br /> 5.508.1 Ozone depletion and greenhouse gas reductions. Installations of HVAC, refrigeration and fire suppression compliance with this code. Special inspectors shall demonstrate competence to the satisfaction of the enforcing
<br /> 5.504.4.3 Paints and coatings. Architectural paints and coatings shall comply with VOC limits in Table 1 of 1. Product certifications and specifications. equipment shall comply with Sections 5.508.1.1 and 5.508.1.2. agency for the particular type of inspection or task to be performed. In addition,the special inspector shall have a Z U
<br /> the ARB Architectural Coatings Suggested Control Measure, as shown in Table 5.504.4.3, unless more 2. Chain of custody certifications. certification from a recognized state, national or international association,as determined by the local agency. The
<br /> stringent local limits apply.The VOC content limit for coatings that do not meet the definitions for the specialty 3. Product labeled and invoiced as meeting the Composite Wood Products regulation(see 5.508.1.1 Chlorofluorocarbons(CFCs). Install HVAC, refrigeration and fire suppression equipment that do not area of certification shall be closely related to the primary job function,as determined by the local agency. a ii
<br /> coatings categories listed in Table 5.504.4.3 shall be determined by classifying the coating as a Flat, Nonflat CCR,Title 17,Section 93120,et seq.). contain CFCs.
<br /> or Nonflat-High Gloss coating, based on its loss,as defined in Subsections 4.21,4.36 and 4.37 of the 2007 Date:
<br /> 9 9. 9 4. Exterior grade products marked as meeting the PS-1 or PS-2 standards of the Note: Special inspectors shall be independent entities with no financial interest in the materials or the
<br /> California Air Resources Board Suggested Control Measure,and the corresponding Flat, Nonflat or Engineered Wood Association,the Australian AS/NZS 2269 or European 636 3S 5.508.1.2 Halons. Install HVAC, refrigeration and fire suppression equipment that do not contain Halons. project they are inspecting for compliance with this code.
<br /> Nonflat-High Gloss VOC limit in Table 5.504.4.3 shall apply. standards.
<br /> 5. Other methods acceptable to the enforcing agency. 5.508.2 Supermarket refrigerant leak reduction.New commercial refrigeration systems shall comply with the 703 VERIFICATIONS Revisions:
<br /> p g 9 Y� p 9 9 Y p Y
<br /> 5.504.4.3.1 Aerosol Paints and coatings. Aerosol paints and coatings shall meet the PWMIR Limits for
<br /> 9 p 9 provisions of this section when installed in retail food stores 8,000 square feet or more conditioned area,and that 09/01/2019
<br /> compounds
<br /> ROC in Section 94522(a)(3)and other requirements, including prohibitions on use of certain toxic utilize either refrigerated display cases,or walk-in coolers or freezers connected to remote compressor units or 703.'1 DOCUMENTATION. Documentation used to show compliance with this code shall include but is not 1
<br /> compounds and ozone depleting substances, in Sections 94522(c)(2)and(d)(2)of California Code of condensingunits.The leak reduction measures apply to refrigeration systems containing high-global-warmingotential limited to,construction documents, plans,specifications, builder or installer certification, inspection reports,or other
<br /> pp Y 9 Y 9 p
<br /> Regulations,Title 17 commencing with Section 94520;and in areas under the jurisdiction of the methods acceptable to the enforcing agency which demonstrate substantial conformance. When specific
<br /> 9 9 1 (high-GWP)refrigerants with a GWP of 150 or greater. New refrigeration systems include both new facilities and the p 9 9 Y
<br /> Bay Area Air Quality Management District additionally comply with the percent VOC by weight of product replacement of existing refrigeration systems in existing facilities. documentation or special inspection is necessary to verify compliance,that method of compliance will be specified in A2 10/04/2019
<br /> limits of Regulation 8 Rule 49. the appropriate section or identified applicable checklist.
<br /> A311/21/2019_
<br /> Page No:
<br /> DISCLAIMER:THIS DOCUMENT IS PROVIDED AND INTENDED TO BE USED AS A MEANS TO INDICATE AREAS OF COMPLIANCE WITH THE 2016 CALIFORNIA GREEN BUILDING STANDARDS(CALGREEN)CODE. DUE TO THE VARIABLES BETWEEN BUILDING DEPARTMENT JURISDICTIONS, THIS CHECKLIST IS TO BE USED ON AN INDIVIDUAL PROJECT BASIS AND MAY BE MODIFIED BY THE END USER TO MEET THOSE INDIVIDUAL NEEDS. THE END USER ASSUMES ALL RESPONSIBILITY ASSOCIATED WITH THE USE OF THIS DOCUMENT,INCLUDING VERIFICATION WITH THE FULL CODE.
<br />
|