WORK PLANS - Laserfiche WebLink

Home Browse Search

N U) DSS I V Y`l-L- 12�� I V Y`l-L- I I�� UL � �I `l Y Y-L- I O� UL DESIGN F-G-2078 GONTINUED UL DESI `l Y`l-L- 1O54 U 0_�L 0_�L I. Wall Assembly - The fire-rated gypsum board/stud wall assembly shall V constructed of the @ • D W materials and in the manner specified in the individual U300, U400 or V400 Series Wall and Partition Designs in the UL fire Resistance Directory and shall include the construction IA IA Features noted below: A A N A A. Studs - Wall framing may consist of either wood studs or steel channel studs. Wood studs to AOI-7 U AOI-7 AOI-1 consist of nom 2 by 4 in, lumber spaced max 16 in. 06. Steel studs to be min 2-1/2 in. wide �y 3 4 Ig and spaced max 24 in. OG. 3 IA Q A B. Gypsum Board* - Nom 5/8 in, thick gypsum board, as specified in the individual Wall and 1 AOI-7 Partition Design. Max diam Of opening is II-1/2 in. The hourly F-Rating Of the Firestop system 1 -RED INC, A-RGHITEGTS is equal to the hourly fire rating Of the wall assembly in which it is installed. J 1211 J STREET,MODESTO,GA 95354 z 3 IA 2. Through-Penetrants - One nonmetallic pipe, conduit or tubing to be installed within the 209.522.8900 I Firestop system. The annular space between pipe and periphery of opening shall be min 0 in. O 3 ® 0 ® ® ® ® ® (point contact) to max I/2 in. Pipe or conduit to be rigidly supported on both sides of the 2 0 2 wall assembly. The following types and sizes of nonmetallic pipes may be used: SEAL: v w I i A. Polyvinyl Chloride (PVC) Pipe - Nom l0 in. diam (or smaller) Schedule 40 solid-core or Q2 cellular core PVG pipe for use in closed (process or supply) or vented (drain, waste or �S ARCH// � 3 IB vent) piping system. � J�p� BURc� 2 P � 1 Y AB. Chlorinated Polyvinyl Chloride (GPVG) Pipe - Nom 10 in, diam (or smaller) SDRI3.5 GPVG pipe IB z IB for use in closed (process or supply) piping systems. �__T3 G/ EL G. Acrylonitrile Butadiene Styrene (ABS) Pipe - Nom 6 in, diam (or smaller) Schedule 40 REN. w solid-core or cellular core ABS pipe for use in closed (process or supply) or vented (drain, tp 03-3I-21 �P SEGTION A-A SEGTION A-A SEGTION A- waste or vent) piping systems SEGTION A- _1TFoFc \�°e D. Flame Retardant Polypropylene (F-RPP) Pipe - Nom 6 in, diam (or smaller) Schedule 40 FRPP a DESIGN/SYSTEM/GONSTRUCTION/ASSEMBLY USAGE DISCLAIMER DESIGN/SYSTEM/CONSTRUGTION/ASSEMBLY USAGE DISGLAIMER DESIGN/SYSTEM/GONSTRUCTION/ASSEMBLY USAGE DISCLAIMER pipe for use in closed (process or supply) or vented (drain, waste or vent) piping system. DESIGN/SYSTEM/GONSTRUCTION/ASSEMBLY USAGE DISCLAIMER `n0 Authorities Having Jurisdiction should be consulted in all cases as to the particular 0 Authorities Having Jurisdiction should be consulted in all cases as to the particular 0 Authorities Having Jurisdiction should be consulted in all cases as to the particular E. Polyvinylidene Fluoride (PVDF) Pipe - Nom 4 in. diam (or smaller) PVDF pipe for use in 0 Authorities Having Jurisdiction should be consulted in all cases as to the particular n requirements covering the installation and use of UL Listed or Classified products, requirements covering the installation and use of UL Listed or Classified products, requirements covering the installation and use of UL Listed or Classified products, closed (process or supply) or vented (drain, waste or vent) piping system. When max 6 in, requirements covering the installation and use of UL Listed or Classified products, q g P q g P q g P q 9 equipment, system, devices, and materials. equipment, s stem, devices, and materials. equipment, s stem, devices, and materials. diam pipe is used, T-Rating is equal to the hourly fire rating of the wall. When nom 8 in, or 10 equipment, s stem, devices, and materials. � ui q. p yyy y ,Ir in, diam pipe is used, T-Rating is 0 hr. CONSULTANT: X 0 Authorities Having Jurisdiction should be consulted before construction. • Authorities Having Jurisdiction should be consulted before construction. • Authorities Having Jurisdiction should be consulted before construction. 0 Authorities Having Jurisdiction should be consulted before construction. 3. Firestop Device* - Firestop Collar - Firestop collar shall be installed in accordance with m 0 Fire resistance assemblies and products are developed by the design submitter and have Fire resistance assemblies and products are developed by the design submitter 0 Fire resistance assemblies and products are developed by the design submitter and have the accompanying installation instructions. Collar to be installed and latched around the pipe 0Fire resistance assemblies and products are developed by the design submitter and have ~D been investigated by UL for compliance with applicable requirements. The published been investigated by UL For compliance with applicable requirements. The published been investigated by UL for compliance with applicable requirements. The published and secured to both sides of the wall using the anchor hooks provided with the collar. been investigated by UL For compliance with applicable requirements. The published Z in Formation cannot always address every construction nuance encountered in the field. information cannot always address every construction nuance encountered in the field. information cannot always address every construction nuance encountered in the field. (Minimum two anchor hooks for 1-1/2 and 2 in, diam pipes, three anchor hooks For 3 and 4 in, information cannot always address every construction nuance encountered ii the field. • When field issues arise, it is recommended the first contact For assistance be the technical 0 When field issues arise, it is recommended the first contact for assistance be the technical 0 When field issues arise, it is recommended the first contact for assistance be the technical diam pipes, four anchor hooks for 6 in, diam pipes, ten anchor hooks for 8 in. diam pipes 0 When field issues arise, it is recommended the first contact for assistance be the technical w service staff provided by the product manufacturer noted for the design. Users of fire service staff provided by the product monuFacturer noted for the design. Users of fire service staff provided by the product manufacturer noted for the design. Users OF fire and twelve anchor hooks for 10 in, diam pipes). The anchor hooks are to be secured to the service staff provided by the product monuFacturer noted For the design. Users of Fire T resistance assemblies are advised to consult the general Guide Information for each resistance assemblies are advised to consult the general Guide Information For each resistance assemblies are advised to consult the general Guide Information for each surface Of wall with 3/16 in, diam by 2-I/2 in, long steel toggle bolts along with washers. As resistance assemblies are advised to consult the general Guide Information for each 0) product category and each group of assemblies. The Guide Information includes specifics product category and each group OF assemblies. The Guide Information includes specifics product category and each group of assemblies. The Guide Information includes specifics an alternate for pipe sizes Of nom 4 in, diam or less, min No. 10 by 1-I/2 in, long drywall or product category and each group of assemblies. The Guide Information includes specifics concerning alternate materials and alternate methods of construction. concerning alternate materials and alternate methods of construction. concerning alternate materials and alternate methods of construction. laminate screws with min 3/4 in, steel washers may be used. When the drywall or laminate concerning alternate materials and alternate methods of construction. screw is used, T-Rating shall not exceed I hr. HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI LL 0 only products which bear UL's Mark are considered as Classified, Listed, or-Recognized. 0 Only products which bear UL's Mark are considered as Classified, Listed, or-Recognized. 0 Only products which bear UL's Mark are considered as Classified, Listed, or-Recognized. ING - GP 643 50/1.5"N, GP 643 63/2"N, GP 643 q0/3"N, GP 643 110/4"N, GP 643 160/6"N, GP Only products which bear UL's Mark are considered as Classified, Listed, or-Recognized. 644 200/8" and GP 644 250/10" Firestop Collars THROUGH PENETRATION FIRE STOP SYSTEM THROUGH PENETRATION FIRE STOP SYSTEM THROUGH44 PENETRATION FIRE STOP SYSTEM 4. void or Cavity Material* - Sealant - (Not Shown) - Min I/2 in. thickness of sealant THROUGH PENETRATION FIRE STOP SYSTEM Design No. W-L-1266 February 14,2008 Design No. W-L-1164 December 6,2000 Design No. W-L-IOG5 January 2, IGGI applied within the annular space for nom 8 in. and 10 in. diam pipes, flush with each side of Design No. W-L-1054 December 4,2002 F Ratings - I and 2 hour (see item 1) F Ratings - I and 2 hour (see items I and 4) F Ratings - I and 2 hour (see item 1) wall. Sealant in annular space is optional for max 6 in. diam pipes. A min 1/4 in. thickness of F Ratings - I and 2 hour (see items I and 3) sealant is required within the annular space, flush with each side of wall, to attain the L T Rating - 0 and 1/4 hour (see item 1) T -Rating - 0 hour T Rating - I and 2 hour (see items 3) -Ratings For max 6 in, diam pipes. T -Rating - O hour L -Rating at ambient - Less than I GFM / SQ. I- I . HILTI CONSTRUCTION CHEMICALS, DIV OF L -Rating at ambient - Less than I GFM / SQ. I- I . I. Wall Assembly - The I or 2 hr fire rated gypsum board/stud wall assembly shall be I. Wall Assembly - The I or 2 hr fire-rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the manner described in the individual U300, U400 or constructed Of the materials and in the manner described in the individual U400 Series Wall L -Rating at 400 F - 4 GFM / SO. H . HILTI INC - FS-One Sealant L -Rating at 400 F - 4 GFM / SQ. I- 1. V400 Series Wall and Partition Design in the UL Fire Resistance Directory and shall include or Partition Design in the UL Fire -Resistance Directory and shall include the following 1. Wall Assembly - The I or 2 In fire-rated gypsum wallboard/stud wall assembly shall be 1. Wall Assembly - The I or 2 hr fire-rated gypsum wallboard/stud wall assembly shall be the following construction Features: construction features: constructed of the materials and in the manner described in the individual U300 or U400 constructed of the materials and in the manner specified in the individual U300 or U400 A. Studs - Wall framing may consist of either wood studs or steel channel studs. Wood studs to A. Studs - Wall framing may consist Of either wood studs or steel channel studs. Wood studs to Series Wa1I and Partition Designs in the UL Fire Resistance Directory and shall include the Series Wall and Partition Designs in the UL Fire Resistance Directory and shall include the consist of nom 2 by 4 in. (51 by 102 mm) lumber spaced I6 in. (406 mm) OC. Steel studs to be consist of nom 2 by 4 in, lumber spaced 16 in. OG. Steel studs to be min 2-1/2 in, wide and following construction features: following construction features: min 3-1/2 in. (861 mm) wide spaced max 24 in. (610 mm) OC. spaced max 24 in. OG. When steel studs are used and the diam of opening exceeds the P A. Studs - Wall Framing may Consist of either wood studs or steel channel studs. Wood studs to A. Studs - Wall framing may consist of either wood studs or steel channel studs. wood studs to Width of stud cavity, the opening shall be framed on all sides using lengths of steel stud B. Gypsum Board* - The gypsum board type, thickness, number of layers, fastener type and consist of nom 2 by 4 in, lumber spaced 16 in. OG. Steel studs to be min 2-I/2 in, wide and consist of nom 2 by 4 in, lumber spaced 16 in, OG. Steel studs be min 2-I/2 in, wide and sheet orientation shall be as specified in the individual U300, U400 or V400 Series Design installed between the vertical studs and screw-attached to the steel studs at each end. spaced max 24 in. OG. spaced max 24 in. OG. When steel studs are used and the diam of opening exceeds the The framed opening in the wall shall be 4 to 6 in, wider and 4 to 6 in. higher than the diam width of stud cavity, the opening shall be Frame on Gill sides using lengths of steel stud in the UL Fire Resistance Directory. Max diam of opening is 10-5/8 in. (2l0 mm). of the penetrating item such that, when the penetrating item is installed in the opening, a 2 B. G sum Board* - 5/8 in. thick, 4 ft wide with square or to eyed edges. The sum hp g g g p g p g yp q p g gyp installed between the vertical studs and screw-attached to the steel studs at each end. G. Steel Sleeve - (Optional, Not Shown) - Cylindrical sleeve fabricated from min O.OICI in. thick to 3 in. clearance is present between the penetrating item and the framing on all four sides. wallboard type, thickness, number of layers, fastener type and sheet orientation shall be as p y The framed opening in the wall shall be 4 to 6 in, wider and 4 to 6 in, higher than the diam (0.48 mm) olv sheet steel and having a min 2 in. (51 mm) Ia along the longitudinal seam. * specified in the individual U300 or U400 Series Design in the UL Fire-Resistance Directory. g 9 P 9 9� B. Gypsum Board - The gypsum wallboard type, thickness, number of layers, fastener type and of the penetrating item such that, when the penetrating item is installed in the opening, a 2 1 0 Length of steel sleeve to be equal to thickness of wall. Sleeve installed b coilin the Max size of opening 2-5/8 in, by 18 in. The hourly F-Rating of the firestop system is equal to g q, y g sheet orientation shall be as specified in the individual U300 or U400 Series Design in the the hourly fire ratio of the wall assembly in which it is installed. to 3 in, clearance is present between the penetrating item and the framing on all four side sheet steel to a diam smaller than the through opening, inserting the coil through the UL Fire-Resistance Directory. Max diam of opening in steel stud walls is 321n.. Max diam of y g y openings and releasing the coil to let it uncoil against the circular cutouts in the gypsum openings in wood stud walls is 14-1/2 in. The hourly F-Ratio OF the Firestop system is equal 2. Electric Metallic Tubing (EMT) - One or more nom I in, diam steel electric tubing. The annular B. Gypsum Board* - 5/8 in, thick, 4 ft wide with square or tapered edges. The gypsum board wallboard layers. y g p y q g g type, thickness, number of layers, fastener type and sheet orientation shall be as specified by HILTON"" y to the hourly fire rating of the wall assembly in which it is installed. space shall be min I/2 in, to a max 1 in. Conduit to be rigidly supported on both sides of wall in the individual U300 or U400 Series Design in the UL Fire-Resistance Directory. Max diam The hour) F -Ratio Of the Firestop system is equal to the hour) fire ratio OF the wall assembly. y g p y q y 9 2. Steel Sleeve - Nom 32 in, diam (or smaller) Schedule 40 (or heavier) steel pipe sleeve of opening is 32-I/4 in. for steel stud walls. Max diam of opening is 14-I/2 in. for wood stud assembly in which it is installed. The hourly T-Rating is 0 and 1/4 Hr for I and 2 Hr rated friction fit in nom 32 in, diam circular opening cut through gypsum board layers. Length Of 3. Fill, Void or Cavity Material* - Sealant - For 2 In F -Rating, min 1-1/4 in. thickness of fill walls. The F-Rating of the firestop system is equal to the fire rating of the wall assembly. assemblies, respectively. steel sleeve to be equal to thickness Of wall, material applied within the annulus, Flush with both surfaces of wall. For I In F-Rating, min 5/8 2. Through-Penetrants - One metallic pipe, conduit, tubing or flexible metal pipe installed in, thickness of fill material applied within the annulus, flush with both surfaces of wall. 2. Through-Penetrants - One metallic pipe, conduit or tubing to be installed either concentrically 3. Through-Penetrant - One metallic pipe, conduit or tubing installed either concentrically or or eccentrically within the Firestop system. The annular space shall be min O in, to max 2-I/4 z concentrically or eccentrically within opening. Annular space between penetrant and HILTI CONSTRUCTION CHEMICALS, DIV OF eccentrically within the firestop system. The annular space between pipe, conduit or tubing in. Pipe may be installed with continuous point contact. Pip Conduit or tubing may be installed L� periphery of opening to be min 0 in. (O mm point contact) to max 2 in. (51 mm). Penetrant to HILTI INC - F5-One Sealant o and the steel sleeve shall be min of O in. (point contact) to max I-7/8 in. Pipe, conduit or at an angle not greater than 45 degrees from perpendicular Pipe, conduit or tubing to be be rigidly supported on both sides of wall. The Following types and sizes of penetrant's may be used: tubing to be rigidly supported on both sides of wall assembly. The following types and sizes *Bearing the UL Classification Mark rigidly supported on both sides of wall assembly. The Following types and sizes of metallic - OF metallic pipes, conduits or tubing may be used: C, /�' �I I,�I pipes, conduits or tubing may be used: A. Steel Pipe - Nom 8 in. (203 mm) diam (or smaller) Schedule 5 (or heavier) steel pipe. A. Steel Pipe - Nom 30 in. diam (or smaller) Schedule 10 (or heavier) steel pipe. 0_��L DSS I L/I Y Y Y-L- 1 O � A. Steel Pipe - Nom 30 in diam (or smaller) Schedule 10 (or heavier) steel pipe. l) B. Iron Pipe Nom 8 in. (203 mm) diam (or smaller) cast or ductile iron pipe. B. Iron Pipe - Nom 30 in. diam (or smaller) service weight (or heavier) cast iron soil pipe or B. Iron Pipe - Nom 30 in, diam (or smaller) cast or ductile iron pipe. G. Conduit - Nom 4 in. (102 mm) diam (or smaller) steel electrical metallic tubing (EMT) or nom 6 Glass 50 (or heavier) ductile iron pressure pipe. G. Conduit - Nom 4 in diam (or smaller) steel electrical metallic tubing or 6 in. diam steel in. (152 mm) rigid steel conduit. G. Conduit - Nom 4 in, diam (or smaller) steel electrical metallic tubing, conduit. D. Copper Tubing - Nom 4 in. (102 mm) diam (or smaller) Type L (or heavier) copper tubing. A D. Go er Tubing Nom 6 in. diam (or smaller) Type L (or heavier) copper tubing. D. Copper Tubing - Nom 6 in, diam (or smaller) Type L (or heavier) copper tubing, pp g - yp pp g• E. Copper Pipe - Nom 4 in. (102 mm) diam (or smaller)�Re Regular (or heavier) co e. AOI1 pp p g copper pipe. E. Copper Pipe - Nom 6 in. diam (or smaller)-Regular (or heavier) Copper pipe. E. Copper Pipe - Nom 6 in, diam (or smaller) regular (or heavier) copper pipe. F. Through Penetrating Product*-Flexible Metal Piping - The following types Of steel flexible 4. Fill, Void or Cavity Material*-Sealant - Min 5/8 in, and 1-1/4 in, thickness Of Fill material 0 IA 3. Fill, Void or Cavity Material* - Sealant - Min 5/8 in. thickness of fill material applied within �Zo metal gas piping may be used: 1.) Nom 2 in. (51 mm) diam (or smaller) steel flexible metal gas applied within annulus, flush with both surfaces of wall assembly for I or 2 hr rated walls, the annulus, Flush with both surfaces of wall. At the point or continuous contact locations 0 � piping. Plastic- covering on piping may or may not be removed on both sides OF floor or wall respectively. Min 1/2 in, diam bead of caulk applied to the penetrant/gypsumboord interface between pipe and wall, a min 1/2 in, diam bead of fill material shall be applied at the pipe O I-) assembly. OMEGA FLEX ING 2.) Nom I in. (25 mm) diam (or smaller) steel flexible metal gas at the point contact location on both sides of wall, wall interFoce on both surfaces of wall. 9 piping. Plastic covering on piping may or may not be removed on both sides of floor or wall 3B HILTI CONSTRUCTION CHEMICALS, DIV OF C__ assembly. GASTITE, DIV OF TITEFLEX 3.) Nom I in. (25 mm) diam (or smaller) steel flexible HILTI CONSTRUCTION CHEMICALS, DIV OF metal gas piping. Plastic covering on piping may or may not be removed on both sides of HILTI INC - FS-ONE Sealant HILTI INC - FS-One Sealant *Bearing the UL Classification Mork F---fl W Floor or wall assembly. WARD MFG L L G � * Bearing the UL Classification Mark 3 E� 3. Fill, Void or Cavity Material* - Caulk or Sealant - Min 5/8 in. (16 mm) thickness of caulk 1� applied within annulus, flush with both surFaces OF wall. Min 1/4 in. 66 mm) diam bead OF caulk �Z &_��L D S I L/I `1 Y Y-L-2O�CJ M applied to gypsum board/penetrant interface at point contact location on both sides of wall. O � 3M COMPANY - IG Classification GP 25WB+ caulk or FB-3000 WT sealant Q_��L DSS I L/I `L Y Y-L-2 128 Ig E E UL DES I O N N-L-20� *Bearing the UL Classification M Q) IB IA �] • A W Aon IB SEGTION A-A "'�� AOII =) %ON C Ak- I Iq DESIGN/SYSTEM/GONSTRUGTION/ASSEMBLY USAGE DISCLAIMER 2 r _" 1 7 AOn 2 2 . I- IA me • Authorities Having Jurisdiction should be consulted in all cases as to the particular I 3 ks) s requirements covering the installation and use OF UL Listed or Classified products, Z IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII equipment, system, devices, and materials. - • Authorities Having Jurisdiction should be consulted before construction. N U��] @° 0° 0 Fire resistance assemblies and products are developed by the design submitter and have 1 3 Z been investigated by UL for compliance with applicable requirements. The published IB 0 I iI I - 3 nformation cannot always address every construction nuance encountered in the field. 4' H I O _R T • When field issues arise, it is recommended the first contact For assistance be the technical � N 2 service staff provided by the product manufacturer noted for the design. Users of fire v resistance assemblies are advised to consult the general Guide Information for each /� N O O 4 3 3 product category and each group of assemblies. The Guide Information includes specifics SEGTION A-A � LX concerning alternate materials and alternate methods of construction. (In 2 �_ i tl' • Only products which bear UL's Mark are considered as Classified, Listed, or-Recognized. 0 Q 0 J � SEGTION I ON A-A THROUGH PENETRATION FIRE STOP SYSTEM SEGTION A- Design No. W-L-1058 February 2q,2000 DESIGN/SYSTEM/GONSTRUGTION/ASSEMBLY USAGE DISGLAIMER - F -Ratings - 2 hour Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements REVISIONS: C) DESIGN/SYSTEM/CONSTRUCTION/ASSEMBLY USAGE DISCLAIMER DESIGN/SYSTEM/GONSTRUGTION/ASSEMBLY USAGE DISGLAIMER covering the installation and use of UL Listed or Classified products, equipment, system, devices, T -Rating - 0 and 1/4 hour (see item 2) Al PLANNING 10/05/2018 s Authorities Having Jurisdiction should be consulted in all cases as to the particular • Authorities Having Jurisdiction should be consulted in all cases as to the particular and materials. E requirements covering the installation and use Of UL Listed or Classified products, requirements covering the installation and use of UL Listed or Classified products,� q, � g p q, • g p Authorities Having Jurisdiction should be consulted before construction. A2 HILTON 10/18/2018 (:7� equipment, system, devices, and materials. equipment, system, devices, and materials. • Fire resistance assemblies and products are developed by the design submitter and have been A HILTON 02/0-7/201q • Authorities Having Jurisdiction should be consulted before construction. Authorities Having Jurisdiction should be consulted before construction. I. Wall Assembly - The fire-rated gypsum wallboard/stud wall assembly shall be constructed of investigated by UL for compliance with applicable requirements. The published information cannot L Fire resistance assemblies and products are developed by the design submitter and have • Fire resistance assemblies and products are developed by the design submitter and have the materials and in the manner specified in the individual U300 or U400 Series Wall and always address every construction nuance encountered ii the field. 77 been investigated by UL For compliance with applicable requirements. The published been investigated by for compliance with applicable requirements. The published Partition Designs in the UL Fire -Resistance Directory and shall include the following 0 When field issues arise, it is recommended the first contact for assistance be the technical service C\) information cannot always address every construction nuance encountered in the field. information cannot always address every construction nuance encountered in the field. construction Features: staff provided by the product manufacturer noted for the design. Users OF fire resistance • When field issues arise, it is recommended the first contact for assistance be the technical When field issues arise, it is recommended the first contact For assistance be the technical A. Studs - Wall framing may consist of either wood studs or steel channel studs. Wood studs to assemblies are advised to consult the general Guide Information For each product category and In service staff provided by the product manufacturer noted for the design. Users of fire service staff provided by the product manufacturer noted for the design. Users Of fire consist of nom 2 by 4 in. lumber spaced 16 in. OG. Steel studs to be min 2-1/2 in. wide and each group of assemblies. The Guide Information includes specifics concerning alternate materials I-) resistance assemblies are advised to consult the general Guide Information For each resistance assemblies are advised to consult the general Guide Information for each spaced max 24 in. OG. and alternate methods of construction. � product category and each group of assemblies. The Guide Information includes specifics product category and each group of assemblies. The Guide Information includes specifics B. Gypsum Board* - Two layers of nom 5/8 in, thick gypsum wallboard, as specified in the Only products which bear UL's Mark are considered as Classified, Listed, or-Recognized. s concerning alternate materials and alternate methods of construction. concerning alternate materials and alternate methods of construction. individual Wall and Partition Design. Max diam of opening is 14-1/2 in. for wood stud walls and THROUGH PENETRATION FIRE STOP SYSTEM _ Only products which bear UL's Mark are considered as Classified, Listed, or-Recognized. Only products which bear UL's Mark are considered as Classified, Listed, or Recognized. 20 in. for steel stud walls. Diam of circular through opening to be min 3/8 in, to max 2-3/4 in, larger than diam of through penetrant's (Item 2). Design No. W-L-20 15 January 9,2003 �:_: THROUGH PENETRATION FIRE STOP SYSTEM THROUGH PENETRATION FIRE STOP SYSTEM F -Ratings - I and 2 hour (see item 4) -QED PROJECT # 18050 2. Through-Penetrants - One metallic pipe or tubing to be installed either concentrically or g eccentrical) within the firesto system. Pipe or tubing to be rigidly supported on both sides HILTON # 0-428ND W Design No. W-L-2128 March 14,2006 Design No. W-L-208 November 29,2005 y P y P g g� y PP T -Rating - O and 2 hour (see item 4) r/ of wall assembly. The following types and sizes of metallic pipes or tubing may be used: F -Ratings - I and 2 hour (see item 1) F -Ratings - I and 2 hour (see item 1) L -Rating at ambient - Less than 1 GFM / SCS. 1- 1 . PLANNING # SPR-18-102 O A. Steel Pipe - 1"1-1/4 in, diam (or smaller) by 0.125 (or heavier) steel pipe. The annular space L -Ratio at 400 F - 4 GFM / SQ. H # �, T -Rating - 0 hour T -Rating - 0, I and 2 hour (see items 2 and 3) L-Rating at ambient - 3 GFM / SQ. FT. shall be min 0 to max 2-3/4 in. The TYRoting is 1/4 hr when steel pipe is used. g PERMIT - �L L -Ratio at 400 F - Less than I GFM / SQ. I- 11. Floor or Wall Assembly - The fire-roted gypsum wallboard/stud wall assembly shall I constructed of the APN # Iq6-2-70-23 1. Wall Assembly - The I or 2 hr fire-rated gypsum wallboard/stud wall assembly shall be g B. Copper Tubing - Nom 4 in, diam (or smaller) Type L (or heavier) copper tubing. The annular constructed of the materials and in the manner specified in the individual U300 or U400 space shall be min 0 to max 3 in. The T rating is 0 hr when copper tubing is used. materials and in the manner specified in the individual U300 or U400 Series Wall and Partition Designs in the UL Fire-Resistance Directory and shall include the Following construction features: DATE: 03.06.Iq Series Wall and Partition Designs in the UL Fire-Resistance Directory and shall include the G. Copper Pipe - Nom 4 in, diam (or smaller) regular (or heavier) copper pipe. The annular -(75 following construction features: space shall be min. 0 to max 3 in. The T rating is 0 hr when copper pipe is used. A. Studs - Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of DRAWN: H.GOLLINS nom 2 by 4 in. lumber spaced I6 in. 06. Steel studs to be mil 2-1/2 in. wide and spaced max 24 in. OC. s A. Studs - Wall framing may consist Of either wood studs or steel channel studs. Wood studs to 3. Firestop System - The firestop system shall consist of the following: GHEGKED: J.MILLE-FR consist Of nom 2 by 4 in, lumber spaced 16 in. OG. Steel studs to be min 2-1/2 in, wide and B. Gypsum Board* - Nom 5/8 in. thick gypsum wallboard, as specified in the individual Wall and Partition A. Steel Wire Mesh - No. & steel wire mesh havinga min I in. Ia along the longitudinal seam. � spaced max 24 in. OG. p g g Design. Max diam of opening is 4 in. Length of steel wire mesh to be 4-3/4 in., centered and formed to fit periphery of through Q) B. Gypsum Board* - 5/8 in. thick, 4 ft wide with square or tapered edges. The gypsum wallboard opening. 2. Metallic Sleeve - (Optional) - Nom 4 in. diam (or smaller) Schedule 40 (or thinner) steel pipe Gast into (�) type, thickness, number of layers, fastener type and sheet orientation shall be as specified wall assembly with joint compound and installed flush with wall surfaces. SHEET TITLE: I- in the individual Wall and Partition Design. Max diam of opening is 3-1/2 in. B. Packing Material - Min 4-I/2 in, thickness of flexible urethane sheet or mineral wool insulation Firmly packed into opening as a permanent Form. Packing material to be recessed from both 3. Electrical Nonmetallic Tubing+ - Nom 2 in, diam (or smaller) corrugated wall electrical nonmetallic tubing LISTED ASSEMBLIES .� 2. Metallic Sleeve Optional - Nom 3-1/2 in. (or smaller) cylindrical sleeve fabricated from min surfaces OF wall as required to accommodate the required thickness of fill material. (ENT) constructed ofpolyvinyl chloride (PVG). Tubing to be rigidly supported on both sides Of wall P y q q 9 g� y PP (� 0.016 in, thick (28 gauge) gals sheet steel and having a min 1-1/4 in, laps along longitudinal G. Fill, Void or Cavity Material* - Sealant - Min 1/4 in, thickness of Fill material applied within assembly. A nom annular space Of 3/4 in, is required within the Firestop system. �K seam. Length of sleeve to be installed flush with wall surfaces. the annulus, flush with both surfaces Of wall. At the point contact location between pipe and See Electrical Nonmetallic Tubing (FKHU) category in the Electrical Gonstruction Materials Directory for wall, a min 1/2 in, diam bead Of caulk shall be applied at the wall/ N 3. Through Penetrant's - One nonmetallic pipe installed within the Firestop system.. Pipe may be pp pipe interface on both names OF manufacturers. - installed at on angle not greater than 45 degrees From perpendicular. Pipe to be rigidly surfaces OF wall assembly. 0 9 9 9 P P P y y 4. Fill, Void or Cavity Material - Sealant - Installed symmetrically on both sides of the wall. The hourly F supported on both sides of wall assembly. The space between pipe and periphery of HILTI GONST-RUGTION CHEMICALS, DIV OF -Rating of the firestop system is equal to the hourly fire rating of the wall assembly in which it is O opening shall be min 1/4 in, to max 11/16 in. The Following types and sizes Of nonmetallic pipes HILTI INC - FS-One Sealant pp installed. Fill material applied within the annulus, flush with each end of the steel sleeve at the thickness may be used: shown in the table below: * Bearing the UL Classification A. Polyvinyl Chloride (PVG) Pipe - Nom 2 in, diam (or smaller) Schedule 40 PVG pipe for use in ge asscaon Mork F -Rating Hr T-Rating Hr Fill Mtl Depth In. �_ closed (process or supply) or vented (drain, waste or vent) piping systems. I 0 5/8 (f) B. Chlorinated Polyvinyl Chloride (GPVG) Pipe - Nom 2 in, diam (or smaller) 5DR13.5 GPVG pipe For use in closed (process or supply) piping systems. 2 2 1-1/4 SHEET NO.: � 4. Fill, Void or Cavity Materials* - Sealont - For I hr F -Rating, min 5/8 in, thickness Of fill HILTI CONSTRUCTION CHEMICALS, DIV OF 77� material applied within the annulus, flush with both surfaces Of wall. For 2 hr F -Rating, min HILTI ING -- FS-One Sealant n 1-1/4 in, thickness of fill material applied within annulus, flush with both surfaces of wall. C__ pp + Bearing the UL Listing Mark A01 8 ~ HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC - FS-ONE Sealant Bearing the UL Classification Marking