|
REVISIONS BY
<br /> 0 07 - 27 -2 20
<br /> Automatic Grease & Oils Removal Units �
<br /> I
<br /> \ RESTROOM
<br /> 19 19 i
<br /> The Thermaco,Inc.Big DipperO Automatic Grease and Oils Removal
<br /> LIMIT OF(10)SEATS
<br /> SEATING EATING AT ERS EXPENSE.
<br /> System is a totally engineered system for the separation and removal71
<br /> Tj T1 SEATING TO ERS
<br /> AOA REQS.
<br /> of free-floatingease & oils from kitchen drain water flows. As
<br /> I
<br /> I
<br /> �
<br /> most food service facility managers already know, grease buildup
<br /> within a building's plumbing drainage system is a major cause of
<br /> O
<br /> i Q
<br /> problems due to drain line blockages. These problems jeopardize (N) ELEC.
<br /> normal operations as well as create health and safety hazards within " ` PANEL
<br /> i C0 Cb
<br /> the facility itself. L
<br /> ao eo
<br /> - ------------------- PARALLEL W
<br /> The Big Dipper® Internal Strainer (IS) System is an automatic, self- CUSTOMER AREA
<br /> '--i �--- I COUNTER SHALL
<br /> cleaningC%2 CQ
<br /> device. As greasykitchen effluent drains from commercial I I 1 KITCHEN (3} I BE 34" MAX. v Q
<br /> ABOVE FINISHED ^^
<br /> to
<br /> kitchen fixtures,the unit traps the grease &oils. Incidental solids in I 1 I i FLOOR. Z v' �
<br /> 111 I 9 " I b cc cc
<br /> the kitchen flow are trapped in a strainer basket for removal. The E- ,--�
<br /> Urease & oils separate from the effluent and rise to the surface o£ ;(E " � I z �- �+
<br /> the stainless steel tank. The unit automatically skims the trapped -- SLOPE 02% MIN. � © 17 m _ w Cd a
<br /> grease &oils at least once per day and transfers the grease &oils to
<br /> ( OD.F.U.)4" ® � E"
<br /> I
<br /> H
<br /> -g --r� 0--CIFIC0 I
<br /> a collection container, A timer controls the self cleaning operation, t py t" --- " U
<br /> activating1-4
<br /> the skimming wheel at the proper time. "Cleaned water 13 "� 4"(7} 4 I Q 0
<br /> exits the nit and flow into the facility drain lines. Big Dipper IS H of ) w -80
<br /> units efficiently service single fixtures such as a 1 to 3-compartment "
<br /> Vol a c�xx •C C
<br /> sink or a pre-rinse station. Big Dipper® Model W-200-IS co
<br /> 14 FREEZER 14 FREEZER 14 FREEZER 14 FREEZER 14 FREEZER 0
<br /> (3 FS FOR
<br /> Units in the Bi Di er° Internal Strainer IS Series -- I a w w U
<br /> 9 pp
<br /> ( )4 SLOPE �2% MIN. ICE MAC 14 U y F a a
<br /> 2 Us W-250-IS • 25 GPM 1.5$ Vs) ©i "(17) y 7 SLOPE 02% MIN. �y " SERVICE AREA w - � Cd
<br /> W-150-IS • 15 GPM (0.95 f/s) W-200-IS t 20 GPM(1.26 } ( ) T (3'� } ®� FF�O cc Cd
<br /> Construction: Construction: Construction: -$ 1 -(!)
<br /> Exterior:304 Stainless Steel,Bright Finish Exterior:304 Stainless Steel,Bright Finish Exterior:304 Stainless Steel,Bright Finish -- " " 3" 2"�► 2 } ( 0 2} " 1 s
<br /> Skimming Rate:201b. hr. 9.08 k hr Skimming Rate:241b./hr.(9.08 kg/hr) 3 4 Ta'
<br /> Skimming Rate:20 lb./hr.(9.08 kg/hr) g / ( kg/hr) g _ __ _
<br /> Solids Strainer Capacity:1.16 gallons(4.41) Solids Strainer Capacity:1.16 gallons(4.41) Solids Strainer Capacity:1.16 gallons(4.41) m
<br /> 2"Inlet/Outlet(50 mm) 2"Inlet/Outlet(50 mm) 2"Inlet/Outlet(50 mm)
<br /> 520W/115V/4.5 Amp.60Hz* 520W/115V/4.5 Amp.60Hz* 520W/115V/4.5 Amp.60Hz* " " "
<br /> " 'll��
<br /> W-350-iS • 35 GPM (2.21 I/s) W-500-IS • 50 GPM (3.15 I/s) 24 BIG DIPPER DIPEMELL
<br /> Construction: Construction: W-350-IS)
<br /> Exterior:304 Stainless Steel,Bright Finish Exterior:304 Stainless Steel,Bright Finish 35G.P.M,85.20LBS}
<br /> Skimming Rate:20 lb./hr.(9.08 kg/hr) Skimming Rate:20 lb./hr.(9.08 kg/hr)
<br /> Solids Strainer Capacity:2.5 gallons(9.51) Solids Strainer Capacity:2.5 gallons(9.51) FLOW CONTROL FITTING
<br /> 3"Inlet/Outlet(75 mm) * 3"Inlet/Outlet(75 mm) * " `" ,f.( ) FLOOR PLAN WASTE & VENT ) N
<br /> 520W/115V/4.5 Amp.60Hz 520W/115V/4.5 Amp.60Hz AIR INTAKE I t
<br /> Specifications subject to change without notice. ? : t G�'k . 1$#t: i � tf,"tj .s L5 1a" f�.�'. ��)i::�z 1� :Iif���� :�)� �i�-(� ����� �e r%tii . � �)�� :� x1�x by ��' "�)�1�<f�.
<br /> 1/4rr_1�_D,t
<br /> *220-240V/50hz models available-please contact Thermaco, Inc.for details. Q p
<br /> _ 3. .^t: q.:. { 1�. �' 1 �i_Ot�.i( �LAi'1 �avl'�R�i':E�.I i�a0 ( `.ti^. (:a�l,=a.�.,' i `. cX t.'�N i
<br /> Note:Installations must comply with all applicable local,state,and national codes for your area. t C; f ££ X g y �3 � d t a>�e . 3 q � � �d r £ � g,to d f i e � C-y 1
<br /> f 'l"i : `et t ''„a` T.I' 'E., a�4,.�+c..u a l'�. ?3,. .k.. E..a�t i.f.-'«.. f. #i{.v ; .'t,.'E�i I.}'3 ' 6'•^ :n l w ...t`.w.f 4..1'b ,.. r° .t.�c,.'4... -L y�,L....: -----------------------------------------
<br /> *Please
<br /> ---.__ __e-_------.___.__-_.....___...-._...._-__..____
<br /> *Please consult Thermaco for de- `,e `1 € i rc a �' f it1a:.'*f J' l �l or a public or pri,', to *r°�we .
<br /> m tails on the specific models tested, � ::t - l.fwl tl t;'� into 1 R ` _
<br /> IED ® ® certified,accepted and/or listed byx" ,not. l eing"t'
<br /> CERTtF £ 5 --sx�� .-��..:< .; 4;. iS � .t'�t n determines t- that a' :I'�''a��'� interceptor 1.� �.^•...ltd.._ _�.
<br /> these organizations 3:..s . 1 .1 ,c � k d)st -: . AFL •.a ii, 1 c;�, .A; y e c nor �I�I C-•
<br /> \a>_z z I � i aa>_ :.�,a a a_� I 1�.� �x i .�, I t i�d
<br /> * * C US installation procedures. y r �g [( } ]) C
<br /> R^. -3� s j Sz J :"t s.. .y, �£: 1y�¢ k}-ted,,
<br /> .y'sC�'t�� ?; { 4'F����} Having #`'' •Y is.c H. r.L.�K EC 3�fi 3 have;`:-. 47 V 1 HJT'.: E I EX Ti-VI iZ 1 IYG -VltHT I if ONVi; TC
<br /> ASMEA112.14.3 .1��"q / :R ,i,Es Ole a ed o EaEw�3f.l."f..6iii E��*;.,.le..i:r the f"E.�#�� .bT� t4� .Y ..... -,-
<br /> Please Visit �� vIE.R ; �>` 1 ;I� Ex^,�T � I z � L�c�. 1 ; ��a �;�
<br /> Wlermaco• i 'l;itilii(� ' Y° } <-li ?t� s�1teth l' f f ca 0 ��t:�diti�"nal eq pinen .[ -.,,el itw _ ... and t--) � � THE Ufa � _ II._
<br /> ® www.big-dipper.com 7=fM ;.< zt �. €' r' w r i t
<br /> 11<�ly01e,�,�e e�®vol For More information! y �1 �,
<br /> rid 11L#ft a gl,f + p-gO Ili ° g.� �fip,ri #'
<br /> Copyright @2005 Big Dipper®Thermaco,Inc. • P.O.$ox 2548•Asheboro, NC 21204•Toll Free:1800)633-4204
<br /> www.big-d'spper.com �a��.F. < F U R '�:r"+.''.. 1 E & V s�'a 'r Ir' , I"' i i i G .�'.' i Z� .�>t`E '.�!F�,:.�`r'� �t ,I E�a i �`"' i i'' I i`�'•.�2 it i CSE'i i
<br /> V:(336)629-4651 • F: (336)626-5739• E-mail:info@thermaco.com • Online: 4.1- a�Ii te.nia tDIAGRAM" ON SHEPTP-7
<br /> Specifications sublect to change without Notice
<br /> TRAPS AND INTERCEPTORS g
<br /> Big Dipper° IS Point Source Automatic Big Dipper® IS Point Source Automatic
<br /> PI�P1aCo& Grease Removal Systems Grease Removal Systems ' i
<br /> Ste 2:Calculate the total load from fixtures that discharge into
<br /> AMPpi2
<br /> ® device or devices shall at no time be greater than the rated P 9
<br /> • - � ®I�w ��� ��� ���� flow of the connected grease; interceptor. No flow control the interceptor. ..
<br /> aa�7 ,_ .... � � 01`�?�f3 i�
<br /> W-350-IS .Specifications _ _ _ _ _
<br /> Specifications device having adjustable or removable parts shall be sizeoF
<br /> approved, The vented flow control device shall be located GREASE Two-
<br /> �� MOTOR(riMER 14"CLEARANCE FROM such that n0 system vent shall be between the flow control COMPART LOAD
<br /> : INTERCEPTOR - MINUTE _
<br /> INSTALLATION INS®RIttI�lTi®� ENCLOSURE TOP OF TANK REQUIRED FOR and the grease interceptor inlet. The vent or air inlet of the FIXTURES ONE-MINUTE DRAINAGE.
<br /> p MENTS {gallons} DRAINAGE PERIOD I
<br /> Allowaminimumof14"clearance from STRAINER BASKET&LID REMOVAL flow control device shall connect with the sanitary drainage PERIOD (gpm)
<br /> top of tank for removal of unit lid. 23.375" . ;, vent system,as elsewhere required by this code,or shall ter- {gpm}
<br /> Suggested Minimum Footprint Dimensions ,<':,
<br /> ----------------- minatc through the roof of the building.and shall not termi-
<br /> gg p READ instruction manual included with a<A,.;, p Compartment
<br /> '! � nate to the free atmosphere inside the building pt -. -- �
<br /> system before doing anything. .a4o�.. size
<br /> __ >....... �.osEo. Exception: Listed grease interceptors>rvtth integral flow
<br /> win for the minimum • con-
<br /> trols or restricting devices shall be installed in an accessible 24 inches x 24
<br /> ___ Install unit allowing o 4TEMS
<br /> clearances shown. INLET ra GGCAse :(9 OUTLET location in accordance with the manufacturer's installation inches x 12 2 44.9 `
<br /> 4" 28.4" -sa -- 23.1" instructions.
<br /> COLLECTOR inches '
<br /> 6" -`
<br /> --- 6" \-' =�a 8QUART
<br /> Make sure the height above the _,a cAaAciTv ,1' 1014.2.1 Capacity.The total capacity in gallons((Tal)(THydrant - 3 -
<br /> o" y it
<br /> i Internal Strainer Access Cover is 17.85"
<br /> (L'}of fixtures discharging into a hydromechanicat grease Rated _
<br /> 8,75" ! enough to remove the strainer. 12.5"
<br /> 12.5"1 --
<br /> g 8.75" interceptor shall not exceed two and one-half tunes the 2 t t
<br /> Appliance if -
<br /> Make piping connections with rubber 3"PIPE certified gallon per minute(gpm) (LJs) flow rate of the
<br /> ------ INLET OUTLET pp ginterceptor ---� y f
<br /> in accordance will Table 1014.2.1. - - 49.9 50 25 P �,
<br /> "No Hub"connectors(provided). INLET/OUT
<br /> -- -- - - --- r tC
<br /> 28.4" For this section, the teen "fixture" shall mean and For sI units: I inch=25.4 mm, i gallon per minute=0.06 L1s, I gallon=
<br /> II Kee outlet piping as straight as os- s �- include each plumbing fixture, appliance, apparatus, or 3.785 L
<br /> 8.75" a I P p P 9 9 p � 17.5 ----r
<br /> SERE VIEW
<br /> i' � sibie.Use only sweep connections. ��® ���� other equipment required to be connected to or discharged
<br /> into a grease interceptor by a provision of this section.
<br /> Install vent on outlet piping. 31.4" --�' 1014.3 Gravity Grease Interceptors. Required gravity ;
<br /> 1014.2.2 Vent.A vent shall be installed downstream of
<br /> grease interceptors shall comply with the provisions of Sec- Air Inlet
<br /> FEATURES: � hydromechanical grease interceptors in accordance with
<br /> 6.5"1 i Fill the tank with water before - p tion 1014.3.1 through Section 1014.3.7. ,
<br /> energizing the power to the motor the requirements of this code. l `I _
<br /> --- -- GC-7 GREASE > Fully automatic self cleaning cycle. Removes I
<br /> 1014.3.1 General.The provisions of this section shall . Flow from.Fixtui$.
<br /> and heater.
<br /> 4.51 COLLECTOR collected grease&offs from tank without any op- apply to the design,construction,installation,and testing
<br /> -------------------- INLET OUTLET
<br /> Set Programmable Time Controller for erator assistance. Comes complete with 24-hour TABLE 1 SE IN of commercial kitchen gravity grease interceptors. -)
<br /> proper operating times. timer and Grease Collector. 23.375" HYDROMECHANiCAL GREASE INTERCEPTOR SIZING 1014.3.2 Waste Discharge Requirements. Waste a-
<br /> USING GRAVITY FLOW RATES
<br /> Equip- ' _ discharge in establishments from fixtures and equipment
<br /> NOTE. Drawing for reference only. •Constructed of corrosion resistant materials SIZE OF GREASE INTERCEPTOR w}1lCh Contain �rrcase, including but not limited to,
<br /> DONT . . . ment must be installed in compliance with
<br /> .
<br /> Install P trap on outlet connection Reduce pipe size on outlet piping. suitable for installation in virtually any location.
<br /> laws,regulations and codes F MAXIMUM FULL scullery: p P' P g p. Z
<br /> all applicable la g DIAMETER o sculle Sinks, of and an sinks,dishwashers,sou ket- >=1ow.Control Orifice Tp.grease,trap.
<br /> of tank. (Note:the unit already has including plumbing codes.Installation should Attractive sanitary Stainless Steel exterior. ONE-MINUTE TWO-MINUTE
<br /> an internal gas Ira GREASE
<br /> es PIPE SLOW DRAINAGE DRAINAGE ties,and Moor drains located in areas where Breast-con-
<br /> 9 p) be performed by a qualified plumber. { )
<br /> (qPM)2
<br /> > PERIOD PERIOD tainino materials exist,shall be permitted to be drained 0
<br /> p Pigu a .0-3U
<br /> ------------------ U >
<br /> • Integrated Motor/Grease Outlet/Heater/Lid en- {gpm) {gpm) into the sanitary waste through the interceptor where FfQiti COntrol)'itting
<br /> ables a fast,do-it-yourself unit operation reversal. approved by the Authority Having Jurisdiction. Q m
<br /> TOP VIEW 2 20 20 l0
<br /> Job Specification: 1014.3.2.1 Toilets and Urinals.Toilets, urinals, M
<br /> •
<br /> Compact footprint. _ ; 60 7 5 31 and other similar fixtures shall not drain through the INSTALLATION U00
<br /> Grease and oils separator(s) shall be Thermaco Bi Dipper automatic grease/oil recovery s stems as manufac- LS -- - - - -
<br /> g pp g rY Y ( )
<br /> Two 2 No-Hub Connectors provided. 4 t 25 150 75 interceptor.
<br /> tured by Thermaco, Inc.,Asheboro, North Carolina as noted on plans. O p U
<br /> - 5 230 250 175 1014.3.2.2 Inlet Pipe.Waste shall enter the inter- � -
<br /> _ ceptor through the inlet pipe.
<br /> Separator Specifications: C' i�i1 ii� C J SINK
<br /> ' � '' 6 375 400 200 1014.3.3 Design. Gravity intercepters shall be eon- � r U
<br /> TECHNICAL DATA UPC For SI units: i incl, 25 imn,1 gallon per minute-0.06 L/S structed in accordance with the applicable standard in t When planning multiple fixture < 06
<br /> Furnish and install _Thermaco Big Dipper Model No. W-350-iS, bright finish type 304 stainless steel exterior,
<br /> interior automatic self-cleaning grease and oil recovery separator(s)for floor mounted Materials: Exterior:304 Stainless Steel, Bright Finish °les: Tabic t 701.1 or the design approved by the Authority _� 1 ty
<br /> discharge into. a single inter- -� t:'� F-
<br /> rotationally molded polyethyleneg g R For interceptor sizing by the fixture capacity sce the example below. (laving Jurisdiction.
<br /> or partially recessed installation,rated at 35 gallons per minute peak flow,70 pounds of grease capacity and includ- Interior: Rotationally Molded Polyethylene 0 = /4 inch slope per foot(2o.s 1mn'„1)haled oo i�4anning's formula with frit- ceptor, avoid long pipe runs.
<br /> Ing as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, cnNwm,I,ASMES,aada,d tion tractor N-_.012. 1014.3.4 Location.Each grease interceptor shall be so Establish interceptor size by
<br /> an integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas Electrical: 115 VAC,60 Hz,520 Watts(4.5 Amps) ASME A112t4.3 and A112.14.4
<br /> Maximum inlet Flow Rate: 35 GPM installed and connected that it shat] be easily accessible ,�
<br /> trap, an integral programmable 24-hour multi-event time control, a field reversible motor location, a field reversible for inspection,cleaning,and removal of the intercepted determin'ing the maximum
<br /> 9 p g
<br /> EXAMPLE 1014.2.1 grease,A gravity grease interceptor that complies with °� ,.�. simultaneous discharge Of all V
<br /> grease/oil sump outlet,quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel Number of Skimming Wheels: 1 lC g g Y g p p I it the sinks on the line. It is also Date 07 -27 - 2020 a
<br /> lid a lift-out strainer basket access, an internal stainless steel strainer basket for collection of coarse solids, and a Skimming Rate: 20 Pounds Per Hour ® SIZING HYDROMECHANICAL GREASE INTERCEPTOR(S) IAPMO Z I001 shall not be installed in a building where Q
<br /> h pertinent sections of USING FIXTURE CAPACITY food is handled. Location of the grease interceptor shall - n recommended that a fiOW con-
<br /> comply grease and oils collection container. Electric assembly shall be tested to comply wit p Grease Retention Capacity: 70+Pounds i PMG ti
<br /> Standards for Safety ANSI/UL 73 and/or ANSI/UL 1004. Electric motor equipped with overload protection.Two C JS Step 1:Determine the flow rate from each fixture. meet the approval of the Authority Having Jurisdiction. } : � it trot be installed before the inter_ Scale
<br /> the S y
<br /> 2 no-hub connectors for plumbing Connection provided. Internal Solids Strainer Capacity: 1.85 Gallons 1 1
<br /> O lt.engthl X lwidthl x iDcptl,l ;2311=gallons x[.75 feu factor] [Drain 1014.3.4.1 Interceptors. Interceptors shall be � ceptor inlet. K.C. r
<br /> Period(i minute or 2 minutes) placed as close as practical to the fixtures they serve. �'. �.. , Drawn Cr
<br /> Cc 2010 Thermaco Inc.•Ail rights reserved Patented/Patents Pending•Specifications subject to change without notice ©2010 Thermaco, Inc.-All rights reserved• Patented/Patents Pending •Specifications subject to change without notice 1 -
<br /> g ,,
<br /> 3 6 629 4651 North America: 800 633 4204 9]10 9]10 646 Greensboro St. -Asheboro,N.C.27204-2548.Phone(336)629-4651 •North America:(800)633 4204 1 � ��`
<br /> 1
<br /> 2 646 Greensboro St. •Asheboro, N. C.27204-2548-Phone( 3 ) ( ) E-mail:info@thermaco.com Online:www:big-dipper.com 206 2019 CALIFORNIA PL ING CODE ��91 I� - Job # 2 - 7 O
<br /> E-mail:info@thermaco.com Online:www.bi di er.com
<br /> 9- pp
<br /> N
<br /> Sheet
<br /> i
<br /> - Of Sheets
<br />
|