|
0
<br /> J Z
<br /> ELECTRICAL SPECIFICATIONS ELECTRICAL LEGEND o z
<br /> STANDARD ABBREVIATIONS
<br /> PART I - GENERAL B. CONDUIT (CONT'D.) F. WIRE SYMBOL DESCRIPTION SYMBOL DESCRIPTION A AMPERE 0
<br /> A. CONDITIONS 2. WHERE CONDUIT ENTERS OUTLET BOXES,FIXTURES OR CABINETS,FIRMLY FASTEN WITH I. CONDUCTOR SIZES SHOWN ON THE DRAWINGS ARE BASED ON COPPER WIRE. UNLESS AFF ABOVE FINISHED FLOOR
<br /> STEEL SET SCREW, COMPRESSION CONNECTORS, OR DOUBLE LOCKNUTS FOR GRC. ALL OTHERWISE SPECIFIED, ALL WIRE SHALL BE TYPE XHHW FOR FEEDERS OR BRANCH LINEAR FLUORESCENT FIXTURE / TELEPHONE OUTLET AT +18" AF ARG FAULT, AMP FUSE (858) 733-2445
<br /> U_ I. FURNISH AND INSTALL A COMPLETELY WIRED AND OPERATIONAL ELECTRICAL 5Y5TEM CONNECTIONS SHALL HAVE BUSHINGS OR INSULATED THROAT CONNECTORS. FIRMLY CIRCUITS LARGER THAN 4 AWG, TYPE THHN/THWN INSULATION FOR FEEDERS AND AFG ABOVE FINISHED GRADE
<br /> AS SHOWN ON THE DRAWINGS AND SPECIFIED HEREIN, INCLUDING BUT NOT LIMITED TO, FASTEN CONDUIT TO THE BUILDING CONSTRUCTION. RUN EXPOSED CONDUIT PARALLEL BRANCH CIRCUITS 4 AWG AND SMALLER. ALL BRANCH CIRCUIT WIRING SHALL BE D LINEAR FLUORESCENT FIXTURE /W WALL TELEPHONE OUTLET AT +54" AIC AMPERE INTERRUPTING CAPACITY designed by:
<br /> o THESE MAJOR ITEMS. TO THE BUILDING LINES, SUPPORTED BY APPROPRIATE HANGERS (UNI5TRUT, T & B OR COPPER SERVICE AND PANEL FEEDERS *1/0 AND LARGER MAY BE ALUMINUM, AL ALUMINUM EKATERINA KOHLWES
<br /> APPLETON, OR EQUAL). PROVIDED THE CONDUCTOR SIXES ARE INCREASED FOR EQUAL OR GREATER o SUSPENDED LINEAR FLUORESCENT FIXTURE Q COMPUTER OUTLET AT +18" ARCH'L ARCHITECTURAL
<br /> • A. LIGHTING FIXTURES AS INDICATED AND SPECIFIED ON THE PLANS. AMPACITY AND EQUAL OR LESS EQUIVALENT VOLTAGE DROP. INCREASE CONDUIT SIZE AS AMP SWITCH
<br /> B. ELECTRICAL PANELS, SERVICE, CONDUIT, WIRING, ETC.,FOR ALL OUTLETS AND 3. COVER METALLIC CONDUIT IN CONTACT WITH EARTH WITH POLYETHYLENE TAPED SPIRAL AS REQUIRED. THE WIRES SHALL BE MARKED WITH COLOR TO SIMPLIFY CIRCUIT FLUORESCENT WALL MOUNT FIXTURE COMBINATION TELE/COMPUTER OUTLET AT +18" AWG AMERICAN WIRE GAUGE
<br /> EQUIPMENT. WRAPPED, 1/2 LAPPED TO PROVIDE 20 MIL. THICKNESS. TAPE SHALL BE SCOTCH NO. 50 IDENTIFICATION. UNLESS OTHERWISE REQUIRED BY LOCAL ORDINANCES GROUND WIRES BC BARE COPPER
<br /> Z C. TELEPHONE OUTLETS AND CONDUIT AS INDICATED. TAPE. CONDUIT AND DUCTS NOT UNDER BUILDINGS AND FEEDER DUCTS SHALL BE SHALL BE GREEN,NEUTRAL WIRES SHALL BE 120V- WHITE, 211V- GRAY, AND LIVE WIRES �� LINEAR FLUORESCENT STRIP FIXTURE 141 FLUSH FLOOR BOX WITH COMBINATION TELE/COMPUTER OUTLET BLDG BUILDING REVISIONS:
<br /> Z INSTALLED PER N.E.C. 300-5. MAKE JOINTS WITH COMPOUND TO BE WATERTIGHT. 208Y/120V AND 120/240 SHALL BE BLACK (PHASE A), RED (PHASE B), AND BLUE C CONDUIT
<br /> B. RELATED WORK BY OTHERS (PHASE C). FOR 480Y/211V CIRCUITS, THE COLOR CODE SHALL BE BROWN (PHASE A), O LIGHT FIXTURE 191
<br /> FLUSH FLOOR BOX w/ TELEVISION OUTLET GAB CABINET No DATE DESCRIPTION
<br /> zI. THE ELECTRICAL CONTRACTOR SHALL PROVIDE CONDUIT, TRENCH, AND BACKFILL FOR ORANGE (PHASE B), AND YELLOW (PHASE C). THE WIRE SHALL BE 12 AWG UNLESS CAT CATALOG/CATEGORY
<br /> 0 ELECTRICAL SERVICE ENTRANCE FROM THE MAIN SERVICE TO UTILITY POINT OF 4. FITTINGS AND CONDUIT BODIES SHALL BE STEEL. NO DIECA5T FITTINGS. OTHERWISE INDICATED. CIRCUIT SHALL BE LABELED IN EACH J-BOX. 0 SURFACE MOUNTED FIXTURE TV TELEVISION OUTLET C/B CIRCUIT BREAKER
<br /> Z
<br /> ELECTRICAL SERVICE. ELECTRICAL CONTRACTOR SHALL COORDINATE THE CKT CIRCUIT
<br /> 5. CONDUIT SIZES SHALL BE AS REQUIRED BY CODE AND A5 INDICATED OR SPECIFIED. 2. WHERE ALUMINUM WIRE IS USED, ALUMINUM CONDUCTOR MATERIAL SHALL COMPLY WITH
<br /> w INSTALLATION OF THE ELECTRICAL SERVICE ENTRANCE WITH SERVING UTILITY COMPANY. PENDANT FIXTURE Tv TELEVISION CAMERA (CCTV) CLG CEILING
<br /> N.E.C. 310-14 AND ALL CONNECTIONS AND TERMINATIONS SHALL BE MACHINE CO, EC CONDUIT ONLY
<br /> D 6. ALL EMPTY CONDUIT SYSTEMS SHALL HAVE A NYLON PULL STRING TO FACILITATE COMPRESSION TYPE EQUAL TO BURNDY "HI PLUG" OR "MAGADAPT",NO EXCEPTIONS.
<br /> 2. THE ELECTRICAL CONTRACTOR SHALL PROVIDE CONDUIT, TRENCH, AND BACKFILL FOR ® RECESSED FIXTURE �_ CIRCUIT BREAKER GOMM COMMUNICATION
<br /> o INSTALLATION OF FUTURE WIRE.
<br /> Z PRIMARY PHONE AND CATV SERVICE FROM THE TELEPHONE TERMINAL BOARD OR GU COPPER
<br /> 3. NO WIRE SHALL BE INSTALLED IN THE CONDUIT SYSTEM UNTIL THE CONDUIT SYSTEM IS ® I �� GABLE TERMINATION DEMO DEMOLITION/DEMOLISH
<br /> o CABINET TO THE PHONE COMPANY AND CATV COMPANY POINT OF SERVICE. 1. SCHEDULE 40 PVC CONDUIT SHALL BE PERMITTED UNDERGROUND WITH PROPER COMPLETE. USE MINERALAC NO. 100 OR EQUIVALENT AS A LUBRICANT TO FACILITATE HIGH BAY FIXTURE
<br /> DISC. DISCONNECT
<br /> C. CODES, REGULATIONS, AND STANDARDS FITTINGS, ALL UL APPROVED AND CEMENTED JOINTS. PENETRATIONS THROUGH FLOOR THE INSTALLATION OF THE CONDUCTORS IN THE CONDUIT SYSTEM. KDWALL MOUNTED FIXTURE FU5E DN DOWN
<br /> SLABS AND BENDS GREATER THAN 22° SHALL BE WRAPPED RIGID GALVANIZED STEEL
<br /> I. THE INSTALLATION SHALL COMPLY WITH APPLICABLE LOCAL AND STATE CODES AND ELBOWS. 4. SPLICES IN EXTERIOR PULL BOXES AND MANHOLES SHALL BE WEATHERPROOF U51NG D WALL SCONCE -�� FUSED DISCONNECT SWITCH DL DWG DRAWING
<br /> EACH
<br /> ORDINANCES, WITH THE REGULATIONS OF THE CURRENTLY ACCEPTED EDITION OF THE "5GOTCHGAST" SPLICE KIT OR APPROVED EQUAL. SEAL ENDS OF CONDUITS AND
<br /> ELECT. ELECTRICAL
<br /> NATIONAL ELECTRIC CODE AND WITH THE REQUIREMENTS OF THE POWER, TELEPHONE, 6. CONDUITS AND OUTLETS SHALL BE CONCEALED WITH THE BUILDING STRUCTURE, EXCEPT DUCTS WITH "DUCTSEAL" OR APPROVED EQUAL.
<br /> z
<br /> AND CATV COMPANIES FURNISHING SERVICES TO THIS INSTALLATION. THAT CERTAIN MOTOR AND LIGHTING FEEDER CONDUITS MAY BE RUN EXPOSED IN WALL WASHER SWITCH ELEV ELEVATOR
<br /> D CERTAIN AREAS AS INDICATED ON THE DRAWINGS. CONDUIT SHOWN TO BE INSTALLED 5. PROVIDE SOLID CONDUCTOR FOR 12 AWG AND SMALLER. �p 0- EM EMERGENCY
<br /> 0 2. THE FOLLOWING INDUSTRY STANDARDS, SPECIFICATIONS, AND CODES ARE MINIMUM IN CABINETS, COUNTERS, AND CASEWORK SHALL BE RUN AS DIRECTED BY THE �0 LETTER REFERS TO FIXTURE SCHEDULE _ TV5S SURGE SUPPRESSOR EMT ELECTRICAL METALLIC TUBING
<br /> 0 REQUIREMENTS: ARCHITECT. G. WIRING DEVICES EQUIP EQUIPMENT
<br /> (D I. WALL SWITCHES SHALL BE SPECIFICATION GRADE AC 51LENT TYPE SWITCHES, 20A, 0 "F" INSIDE INDICATES FLUORESCENT CURRENT TRANSFORMER (E),EXIST EXISTING
<br /> o1.THE NATIONAL ELECTRICAL MANUFACTURER'S ASSOCIATION STANDARDS. S. ALL CONDUIT SYSTEMS SHALL HAVE A CODE SIZED COPPER GROUND CONDUCTOR FBO FURNISHED BY OTHERS
<br /> B. THE NATIONAL ELECTRICAL CODE, INCLUDING LOCAL AMENDMENTS. INCREASE CONDUIT 51ZE AS REQUIRED. 120/211 VOLT. •t SPOT LIGHT r POTENTIAL TRANSFORMER FF FINISHED FLOOR
<br /> G. UNDERWRITER LABORATORIES INCORPORATED STANDARDS. FIXT FIXTURE
<br /> 0 2. RECEPTACLES SHALL BE SPECIFICATION GRADE, DUPLEX TYPE,NEMA 5-20R, 20
<br /> z D. AMERICAN NATIONAL STANDARDS INSTITUTE. 10. CONDUIT PENETRATION THROUGH ROOF SHALL HAVE ROOF FLASHING WITH CAULK TYPE �� TRACK LIGHT FIXTURE �_ GROUNDING ELECTRODE FLEX FLEXIBLE METALLIC CONDUIT(STEEL)
<br /> AMPERE, 120 VOLT GROUNDED TYPE. SPECIAL APPLICATION RECEPTACLES SHALL BE
<br /> F. 2019 CALIFORNIA ELECTRICAL GODE (CEC) COUNTER FLASHING SLEEVE. INSTALLATION SHALL BE WATERTIGHT. FLUOR FLUORESCENT
<br /> o INDICATED ON PLANS. MOUNT WITH THE GROUND DOWN. m m m VANITY LIGHT BAR OM POWER METER FT FEET OR FOOT
<br /> G. 2019 CALIFORNIA GREEN BUILDING STANDARDS CODE (GGBSG)
<br /> • H. 2019 CALIFORNIA BUILDING ENERGY EFFICIENCY STANDARDS 11. CONDUIT5 SHALL BE ROUTED SURFACE ON THE STRUCTURE, PARALLEL AND 3. DEVICE PLATES SHALL BE EQUAL TO SIERRA SMOOTH-LINE PLASTIC WALL PLATES. GFA GROUND FAULT ALARM
<br /> I. 2019 CALIFORNIA BUILDING CODE (CBC) PERPENDICULAR TO THE STRUCTURE. COLOR SHALL BE WHITE, UNLESS OTHERWISE NOTED. •-❑ POLE MOUNTED FIXTURE /a MOTOR GFCI GROUND FAULT CIRCUIT INTERRUPTER
<br /> GND GROUND
<br /> D. INSPECTION OF SITE C. OUTLET, PULL, AND JUNCTION BOXES 4. RECEPTACLES IN OUTDOOR AND WET LOCATIONS SHALL BE INSTALLED WITH A HINGED O BOLLARD LIGHT FIXTURE /a GENERATOR HP HORSEPOWER
<br /> z OUTLET COVER/ENCLOSURE CLEARLY MARKED AND U.L. LISTED SUITABLE FOR WET HVAC HEATING,VENTILATING&AIR CONDITIONING
<br /> J I. EACH SWITCH, LIGHT. RECEPTACLE OR OTHER OUTLET SHALL BE PROVIDED WITH A 1 1 PILOT LIGHT ST SHUNT TRIP IBC INTERNATIONAL BUILDING CODE
<br /> I. PRIOR TO SUBMITTING A BID FOR ELECTRICAL WORK, THE CONTRACTOR SHALL VISIT CODE GAUGE,GALVANIZED STEEL OUTLET BOX. JUNCTION AND PULL BOXES SHALL BE LOCATIONS WHILE IN USE, EQUAL TO TAYMAC SPECIFICATION GRADE.
<br /> Z THE SITE OF THE PROPOSED CONSTRUCTION AND SHALL THOROUGHLY ACQUAINT IMC INTERMEDIATE METAL CONDUIT
<br /> 0CODE GAUGE,GALVANIZED STEEL. OUTLET BOXES SHALL BE OF THE ONE PIECE, H. LIGHTING FIXTURES
<br /> HIMSELF WITH EXISTING UTILITIES, AND WORKING CONDITIONS TO BE ENCOUNTERED, ETC. O WARNING LIGHT GFI GROUND FAULT INTERRUPT IN INCHES)
<br /> 0 ALLOWANCE WILL NOT BE MADE FOR NONCOMPLIANCE WITH THIS CONDITION AFTER KNOCKOUT TYPE, IN GENERAL 4" SQUARE WITH PLASTER RING. PLASTER RINGS SHALL
<br /> Z I. PROVIDE ALL LIGHTING FIXTURES, WIRED AND CONNECTED. THE DRAWINGS INDICATE IRC INTERNATIONAL RESIDENTIAL CODE
<br /> BE SET TO PROVIDE NOT MORE THAN I/8" FROM WALL SURFACE TO RING. IN NO CASE
<br /> BIDDING. THE FIXTURES FOR EACH LOCATION. PROVIDE LAMPS FOR ALL FIXTURES. THE LAMPS ® EXIT SIGN TRANSFER SWITCH ISC SHORT CIRCUIT AMPERES
<br /> w SHALL PLASTER RING PROJECT BEYOND SURFACE OF WALL. SINGLE GANG RINGS
<br /> SHALL BE BY THE SAME MANUFACTURER. VERIFY CEILING CONSTRUCTION BEFORE JB,J-BOX JUNCTION BOX
<br /> 2. ELECTRICAL INSTALLATION SHALL MEET THE EXISTING CONDITIONS. SIMILAR TO STEEL CITY 52050 SHALL BE USED FOR 4" BOXES IN UNFINISHED BRICK EMERGENCY FIXTURE KCMIL,MCM THOUSAND CIRCULAR MILS
<br /> o NUMBER 180 BOXES MAY BE USED FOR UNFINISHED MASONRY FLUSH WALL OUTLETS. ORDERING RECESSED UNITS. PROVIDE PLASTER FRAMES AND HANGERS AS REQUIRED. J JUNCTION BOX KVA KILOVOLT AMPERE
<br /> z CENTER ALL OUTLET BOXES IN BLOCK COURSE. CEILING CONSTRUCTION, ARCHITECTURAL ACCESSORIES, VOLTAGE, AND BALLASTS TO
<br /> E. STORAGE AND HANDLING OF MATERIAL MEET THE EXISTING CONDITION. I{JO0 FIXTURE w/ EMERGENCY BATTERY BALLAST KW KILOWATT
<br /> 2. BOXES INSTALLED IN POURED CEMENT FLOORS SHALL BE FLUSH TYPE CAST IRON OR FLUSH MOUNT FLOOR JUNCTION BOX LTG LIGHTING
<br /> I. DELIVER MATERIALS AND EQUIPMENT TO THE PROJECT IN THE MANUFACTURER'S STEEL WITH WATERTIGHT GASKETED COVERS. WHERE BOXES ARE INSTALLED IN FLOORS I. SERVICE ENTRANCE SECTION S SINGLE POLE SWITCH, 20A, 120/211V MAX. MAXIMUM
<br /> ORIGINAL, UNOPENED, LABELED CONTAINERS. PROTECT AGAINST MOISTURE, TAMPERING, WALL MOUNTED SENSOR MGB MAIN CIRCUIT BREAKER
<br /> OR DAMAGE FROM IMPROPER HANDLING OR STORAGE. CONTRACTOR SHALL PROTECT WITH TILE OR CARPET FLOOR COVERING, COVERS SHALL BE OF THE RECESSED TYPE I. THE SERVICE ENTRANCE EQUIPMENT SHALL BE AS INDICATED ON THE DRAWINGS. S TWO POLE SWITCH, 20A MECH. MECHANICAL
<br /> AND BE RESPONSIBLE FOR ANY DAMAGE TO WORK OR MATERIALS UNTIL FINAL TO ACCOMMODATE THE FLOOR COVERING. EQUIPMENT SHALL CARRY THE U.L. LABEL AND SHALL CONFORM TO THE POWER 2 (14-1 THERMOSTAT OUTLET AT +54" MIN. MINIMUM
<br /> d ACCEPTANCE BY THE OWNER, AND SHALL MAKE GOOD WITHOUT COST TO THE OWNER, COMPANY REGULATIONS. S THREE-WAY SWITCH, 20A, 120/211V MLO MAIN LUGS ONLY
<br /> z ANY DAMAGE OR LOSS THAT MAY OCCUR DURING THIS PERIOD. 3• BOXES INSTALLED FOR THE ALARM, COMPUTER, AND SECURITY SYSTEM SHALL BE g
<br /> PROVIDED WITH APPROPRIATE COVER PLATES. 2. SERVICE ENTRANCE EQUIPMENT SHALL BE PROVIDED WITH A FULLY RATED COPPER OR CIRCUIT BREAKER IN DEDICATED ENCLOSURE MTD MOUNTED
<br /> D ALUMINUM BUS. HORIZONTALLY TAPERED BUSSING SHALL NOT BE ALLOWED. S FOUR-WAY SWITCH, 20A, 120/211V NC NORMALLY CLOSED
<br /> 0 2. ARRANGE FOR TIMELY DELIVERY OF MATERIALS AND EQUIPMENT TO THE JOB SITE IN 4 BOXES FOR TELEPHONE, COMPUTER, T.V.,FIRE ALARM, SECURITY, AND SIMILAR SYSTEMS 4 ® RELAY NEC NATIONAL ELECTRICAL CODE
<br /> 0 ORDER TO MINIMIZE THE LENGTH OF TIME BETWEEN DELIVERY AND INSTALLATION.
<br /> Z SHALL BE MINIMUM 4" SQUARE AND 2-1/8" DEEP. J. SYSTEM GROUNDING SD DIMMER SWITCH, MIN. 2000W, 120/211V NECA NATIONAL ELECTRICAL CONTRACTOR'S ASSOCIATION
<br /> 3. COVER AND PROTECT ANY MATERIAL WHICH MAY BE AFFECTED BY THE WEATHER WHILE I. GROUNDING SHALL COMPLY WITH REQUIREMENTS OF ARTICLE 250. ALL EXPOSED TS TIME SWITCH NEMA NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION
<br /> w S HP RATED MOTOR SWITCH WITH THERMAL OVERLOAD PROTECTION NEUT NEUTRAL
<br /> 0
<br /> IN TRANSIT OR STORED AT THE PROJECT SITE. ANY MATERIAL FOUND DEFECTIVE OR D. SWITCHBOARDS NONCURRENT CARRYING METALLIC PARTS OF ELECTRICAL EQUIPMENT,METALLIC M
<br /> NOT INSTALLED IN ACCORDANCE WITH THE CONTRACT DOCUMENTS MAY BE REJECTED RACEWAY SYSTEMS,METALLIC CABLE ARMOR,GROUNDING CONDUCTOR OF CONTACTOR NFC NATIONAL FIRE CODE
<br /> o I. SWITCHBOARDS SHALL BE PROVIDED WITH FULLY RATED COPPER OR ALUMINUM BUS. S LOWER CASE LETTER DENOTES FIXTURES TO BE CONTROLLED NF NON-FUSIBLE
<br /> Z BY THE ENGINEER NONMETALLIC SHEATHED CABLES,GROUNDING CONDUCTOR IN NONMETALLIC RACEWAYS, 8
<br /> HORIZONTAL TAPERED BUSSING SHALL NOT BE ALLOWED. T TRANSFORMER NIC NOT IN CONTRACT
<br /> 0
<br /> F. CLEANUP AND GROUNDED CONDUCTORS OF THE WIRING SYSTEM SHALL BE GROUNDED. SK KEY SWITCH, 20A, 1201211V NL NIGHT LIGHT
<br /> 2. ACCEPTABLE MANUFACTURERS - CUTLER HAMMER, SEIMENS, SQUARE D OR APPROVED 2. GROUNDING CONDUCTOR (NEUTRAL)OF THE WIRING SYSTEM SHALL BE CONNECTED TO ®T AUTOMATIC TRANSFER SWITCH NO NORMALLY OPEN
<br /> • I. KEEP THE PREMISES FREE FROM ACCUMULATION OF WASTE MATERIALS,OR RUBBISH EQUAL. THE SYSTEM GROUNDING CONDUCTOR AT A SINGLE PLACE IN EACH SYSTEM BY DENOTES DUAL LEVEL SWITCHING NPCO NEVADA POWER COMPANY 0
<br /> CAUSED BY EMPLOYEES OR WORK UNDER THIS DIVISION OF THE SPECIFICATIONS. AT REMOVABLE BONDING JUMPERS, SIZED ACCORDING TO THE APPLICABLE PROVISIONS PG PHOTOCELL NTS NOT t0 SCALE
<br /> THE COMPLETION OF THE WORK REMOVE ALL SURPLUS MATERIALS, TOOLS, ETC., AND 3. FACTORY ASSEMBLED DEAD FRONT,METAL ENCLOSED, AND SELF-SUPPORTING OF THE NATIONAL ELECTRICAL CODE. THE GROUNDED CONDUCTOR (NEUTRAL)TO THE � PUSH BUTTON CONTROL STATION OCP OVERCURRENT PROTECTION Z Z
<br /> z LEAVE THE PREMISES BROOM-CLEAN. SWITCHBOARD ASSEMBLY CONFORMING TO NEMA PB 2, AND UL 891, AND COMPLETE GROUNDING CONDUCTOR CONNECTION SHALL BE LOCATED IN THE ENCLOSURE FOR THE FIRE ALARM HORN/STROBE P POLE (� W
<br /> FROM INCOMING LINE TERMINALS TO LOAD SIDE TERMINATIONS. Q OCCUPANCY SENSOR SWITCH PH PHASE Cn R
<br /> J SYSTEM'S OVERCURRENT PROTECTION OR WHERE OTHERWISE INDICATED ON THE PLANS V
<br /> cf) G. EXCAVATION OR SPECIFICATIONS. m ❑i NON-FUSED DISCONNECT SWITCH PNL PANEL w
<br /> Z 4. LINE AND LOAD TERMINATIONS: ACCESSIBLE FROM THE FRONT ONLY OF THE `Y SINGLE RECEPTACLE,NEMA 5-20R, 20A, 125V PV PV PHOTOVOLTAIC 0 w
<br /> 0 I. PERFORM ALL EXCAVATION AND BACK FILLING REQUIRED FOR WORK PERFORMED SWITCHBOARD. SUITABLE FOR THE CONDUCTOR MATERIALS AND NUMBER OF 3. A GROUND BUS SEPARATE FROM THE NEUTRAL BUS SHALL BE PROVIDED IN ALL ni VENDOR FURNISHED DISCONNECT SWITCH PVC POLYVINYL CHLORIDE J
<br /> UNDER THI5 DIVISION OF THE SPECIFICATIONS. USE EXCAVATED MATERIALS FOR CONDUCTORS USED.
<br /> SWITCHBOARDS AND PANELBOARD5. GROUND BUS SHALL BE RETORQUED (CHECKED) DUPLEX RECEPTACLE,NEMA 5-20R, 20A, 125v PWR POWER LLI
<br /> Er
<br /> U11)] BACKFILL UNLESS OFF SITE MATERIALS ARE DEEMED NECESSARY. BUS CONNECTIONS: BOLTED. ACCESSIBLE FROM FRONT FOR MAINTENANCE. PROVIDE PRIOR TO ENERGIZING EQUIPMENT PER MANUFACTURER'S RECOMMENDATIONS. Di FUSED DISCONNECT SWITCH QTY QUANTITY
<br /> BELLEVILLE WASHERS FOR AND PROPERLY TORQUE ALL CONNECTIONS. O 0
<br /> J DOUBLE DUPLEX RECEPTACLE,NEMA 5-20R,20A, 125V REGEP RECEPTACLE
<br /> H. DRAWINGS 4. GROUND BUSES AND NEUTRAL BUSES IN ALL DISTRIBUTION PANELS, SWITCHBOARDS, ® MOTOR CONTROLLER OR STARTER REQ'D REQUIRED
<br /> 0 5. PROVIDE FULLY-RATED NEUTRAL BUS AND FULLY RATED GROUND BUS MATCHING
<br /> Z PANELBOARD5, AND TH05E PROVIDED IN ANY EQUIPMENT SHALL BE 150LATEID DUPLEX RECEPTACLE / HALF-SWITCHED RSC RIGID STEEL CONDUIT
<br /> :5I. THE DRAWINGS INDICATE THE GENERAL ARRANGEMENT AND LOCATIONS OF THE MATERIAL USED FOR MAIN BUS. W Z
<br /> o ELECTRICAL WORK DATA PRESENTED ON THESE DRAWINGS ARE AS ACCURATE AS EXCEPT WHERE REQUIRED TO BE CONNECTED AS SPECIFIED ABOVE FOR THE SERVICE COMBINATION CONTROLLER/DISCONNECT SWITCH 30/3/15/1 SCHED SCHEDULE
<br /> PLANNING CAN DETERMINE, BUT FIELD VERIFICATION OF ALL DIMENSIONS, LOCATIONS, 6. FUTURE PROVISIONS: FULLY EQUIP SPACES FOR FUTURE DEVICES WITH BUSSING AND BUS ENTRANCE AND IN TRANSFORMER TERMINAL COMPARTMENTS. G� DUPLEX RECEPTACLE MOUNTED ABOVE COUNTER - VERIFY DENOTES AMPERES/POLES�FUSEIOR BREAKER)/NEMA STARTER SIZE. SECT SECTION O
<br /> • LEVELS, ETC., TO SUIT FIELD CONDITIONS 15 REQUIRED. REVIEW ALL ARCHITECTURAL, CONNECTIONS. SUITABLY INSULATED AND BRACED FOR SHORT CIRCUIT CURRENTS. MOUNTING HEIGHT 5P SINGLE POLE
<br /> STRUCTURAL, AND MECHANICAL DRAWINGS AND ADJUST ALL WORK TO MEET THE 5. WHEN INDICATED ON THE DRAWINGS, EQUIPMENT GROUNDING CONDUCTORS SHALL BE VENDOR FURNISHED COMBINATION CONTROLLER/DISCONNECT SN SOLID NEUTRAL 2 Z
<br /> CONTINUOUS CURRENT RATING AS INDICATED ON DRAWINGS. Z
<br /> � EXTENDED FROM THE GROUND BUS IN THE DISTRIBUTION EQUIPMENT TO THE � GFGI RECEPTACLE SWITCH SPEC SPECIFICATION Q
<br /> REQUIREMENTS OF CONDITIONS SHOWN. THE ARCHITECTURAL DRAWINGS SHALL TAKE RECEPTACLE,FIXTURE OR DEVICE LUGS WHERE THEY ARE PROVIDED. WHERE LUGS
<br /> z PRECEDENCE OVER ALL OTHER DRAWINGS. DISCREPANCIES BETWEEN DIFFERENT E. PANEL BOARDS ARE NOT PROVIDED, EQUIPMENT GROUNDING CONDUCTORS SHALL BE CONNECTED TO SW SWITCH Z _
<br /> PLANS,OR BETWEEN DRAWINGS AND SPECIFICATIONS, OR REGULATIONS AND CODES ® SPECIAL PURPOSE OUTLET (TYPE AS NOTED) LG LIGHTING CONTACTOR SWBD SWITCHBOARD Q
<br /> ~ EQUIPMENT ENCLOSURES. THE CONNECTIONS SHALL BE ARRANGED SUCH THAT SWGR SWITCH GEAR
<br /> D GOVERNING THE INSTALLATION SHALL BE BROUGHT TO THE ATTENTION OF THE ENGINEER I. CIRCUIT BREAKER TYPE AS INDICATED ON DRAWINGS. UNLESS INDICATED OTHERWISE,
<br /> W IN WRITING BEFORE THE DATE OF BID OPENING. IF DISCREPANCIES ARE NOT ALL PANELS SHALL HAVE PANEL BOARD TYPE CONSTRUCTION WITH BOLT-ON CIRCUIT REMOVAL OF THE RECEPTACLE, EQUIPMENT GROUND CONDUCTORS, OR GROUND I© CLOCK OUTLET w/ RECESSED COVER PLATE AT +90" GR CARD READER SYS SYSTEM 2i Q
<br /> 0 JUMPERS FROM GROUND BUSING SHALL NOT AFFECT THE GROUND SYSTEM.
<br /> 0 REPORTED, THE CONTRACTOR SHALL BID THE GREATER QUANTITY OR BETTER QUALITY, BREAKERS FOR 34 PANELS. MANUFACTURERS SHALL BE GENERAL ELECTRIC, SQUARE TEMP TEMPORARY
<br /> Z TIME CLOCK TELE TELEPHONE LLI
<br /> AND APPROPRIATE ADJUSTMENTS WILL BE MADE AFTER CONTRACT AWARD. D, SIEMENS, CUTLER-HAMMER OR EQUAL WITH VOLTAGE, SIZES, AND RATINGS AS ® CEILING DUPLEX RECEPTACLE TG
<br /> 0 CONTRACTOR SHALL BE RESPONSIBLE TO FIELD MEASURE AND CONFIRM MOUNTING 6. RACEWAYS MAY NOT BE USED AS A GROUNDING CONDUCTOR FOR POWER AND LIGHTING T-STAT THERM05TAT Ir ON DRAWINGS. CIRCUITS. ALL CONDUIT SHALL HAVE SEPARATE CODE SIZED GREEN GROUND WIRE ®
<br /> I
<br /> HEIGHTS AND LOCATION OF ELECTRICAL EQUIPMENT WITH RESPECT t0 COUNTERS, INSTALLED IN THE CONDUIT TO INSURE A CONTINUOS GROUNDING PATH. FLOOR OUTLET w/ DEVICE AS INDICATED FS FLOW SWITCH TTB TELEPHONE TERMINAL BACKBOARD ,
<br /> U
<br /> RADIATION, ETC. DO NOT SCALE DISTANCES OFF THE ELECTRICAL DRAWINGS, USE 2. THE CIRCUIT BREAKERS SHALL BE OPERABLE IN ANY POSITION AND BE REMOVABLE TTC TELEPHONE TERMINAL CABINET ' ' W U
<br /> ACTUAL BUILDING DIMENSIONS. FROM THE FRONT OF THE PANEL BOARD WITHOUT DISTURBING THE ADJACENT UNITS. 1. IN INACCESSIBLE LOCATIONS,MAKE CONNECTIONS BY EXOTHERMIC WELD PROCESS. COMBINATION FLOOR OUTLET w/DEVICES AS INDICATED TS TAMPER SWITCH TYP. TYPICAL U W
<br /> BRANCH BREAKERS SHALL BE OF SUCH DESIGN THAT COMBINATION OF SINGLE-POLE, UBC UNIFORM BUILDING CODE Q
<br /> 0 6. IN ACCESSIBLE LOCATIONS, CONNECTIONS SHALL BE MADE WITH BOLTED THROUGH,
<br /> I. EXCAVATION, CUTTING, AND FITTING DOUBLE-POLE, AND THREE-POLE BREAKERS CAN BE ASSEMBLED ON THE SAME MULTI-OUTLET SURFACE RACEWAY w/NEMA 5-20R, SD SMOKE DETECTOR UL UNDERWRITERS LABORATORY L.L
<br /> LE
<br /> E
<br /> 5OL
<br /> E
<br /> O
<br /> PRVD DR56RONZE GROUNDING DV . Er W N
<br /> • PANEL. EACH BRANCH CIRCUIT SHALL BE CLEARLY NUMBERED. BRANCH AND MAIN AP20A, 125V AT 12" ON CENTER. U.N.O. UNLESS NOTED OTHERWISE
<br /> I. PERFORM THE EXCAVATION,CUTTING,FITTING, REPAIRING, AND FINISHING OF THE WORK TERMINALS SHALL BE OF THE 5OLDERLE66 TYPE. HANDLE TIES TO FORM MULTI-POLE S. BOND TOGETHER METAL SIDING NOT ATTACHED TO GROUNDED STRUCTURE BOND TO FD FIRE/SMOKE DAMPER v VOLT OR VOLTAGE ::) Z r
<br /> NECESSARY FOR THE INSTALLATION OF THE EQUIPMENT OF THI5 SECTION. HOWEVER,NO BREAKERS NOT ACCEPTABLE. GROUND. PB PULL50X - EXTERIOR VA VOLT AMPERE Z (� q � J
<br /> GUTTING OF THE WORK OF OTHER TRADES OR OF ANY STRUCTURAL MEMBERS SHALL BE CARBON MONOXIDE DETECTOR(SPECIFIED BY MECHANICAL VD VOLTAGE DROP W O J
<br /> DONE WITHOUT THE CONSENT OF THE ARCHITECT. 3. WIRE TERMINATION FOR PANEL BOARDS AND CIRCUIT BREAKERS SHALL BE LISTED AS K. TELEPHONE SYSTEM 0 TELEPHONE TERMINAL CABINET AT +12" TO TOP CO ENGINEER) VP VAPOR PROOF Q Q
<br /> J SUITABLE FOR 15 DEGREES C. W WATT,WIRE 0 Q
<br /> I. TELEPHONE WALL OUTLETS SHALL CONSIST OF STANDARD BOXES MOUNTED IS ABOVE W U U
<br /> z J. COOPERATION WITH OTHER CONTRACTORS THE FLOOR UNLESS OTHERWISE INDICATED. CONNECT OUTLETS TO TELEPHONE TELEPHONE BACKBOARD O SMOKE DETECTOR(SUBSCRIPT "D" INDICATES DUCT MOUNTED) WCR WITHSTAND CURRENT RATING Q -
<br /> 0 4. PROVIDE A TYPEWRITTEN CIRCUIT INDEX BEHIND CLEAR PLASTIC COVER ON IN51DE OF WP UL LISTED WEATHERPROOF,NEMA 3R J
<br /> 0 I. COOPERATE WITH THE OTHER TRADES 50 THAT THE INSTALLATION OF THE ELECTRICAL TERMINAL WITH SEPARATE 3/4 CONDUIT UNLESS OTHERWISE SHOWN ON DRAWINGS. Z
<br /> Z OUTLETS AND EQUIPMENT WILL BE PROPERLY COORDINATED. CONDUIT, LIGHTING DOOR. INFORMATION SHALL INCLUDE ROOM AND TYPE LOAD SERVED. ALL CIRCUIT PROVIDE A TERMINAL MOUNTING BOARD FOR THE INCOMING SERVICE CABLE. PANEL50ARD - SURFACE AT +12" TO TOP O HEAT DETECTOR WR UL LISTED WEATHER RESISTANT,NEMA 3R O M O O
<br /> BREAKERS SHALL BE IDENTIFIED, INCLUDING SPARES. INDEX CARD FRAME SHALL BE XFMR TRANSFORMER fr LLJ 2
<br /> 0 FIXTURES, AND OTHER EQUIPMENT LOCATIONS SHALL BE CHECKED WITH OTHER TRADES METAL, SECURED TO DOOR. = PANELBOARD - RECESSED AT +12" TO TOP O SPEAKER, CEILING OR WALL MOUNTED O LLJ Y
<br /> J TO AVOID CONFLICT WITH THE PIPING, DUCTWORK, STEEL, BEAMS, OR OTHER L. LIGHTING CONTROL U
<br /> o OBSTRUCTIONS. 5. WHERE PANEL BOARDS ARE INSTALLED FLUSH WITH THE WALLS, EXTEND EMPTYIFURNISH AND INSTALL TIME SWITCHESPHOTOCELLSCONTACTORS AND FULL LIGHTING ® SWITCHBOARD OR DISTRIBUTION BOARD DH DOOR HOLD OPEN 01O N O W
<br /> z CAREFULLY CHECK THE LOCATIONS OF THE OUTLET BOXES AND DETERMINE THAT THEY CONDUITS FORM THE PANEL BOARD . , ,TO AN ACCESSIBLE SPACE ABOVE OR BELOW. 2 I0 O 0
<br /> HAVE NOT BEEN DISTURBED DURING THE INSTALLATION OF MATERIALS OF OTHER PROVIDE 3/4" (MINIMUM SIZE)CONDUIT FOR EVERY THREE SINGLE SPARE CIRCUIT CONTROL SYSTEMS AS REQUIRED FOR LIGHTING CONTROLS INDICATED ON THE _
<br /> ° TRADES. DRAWINGS. SERVICE PEDESTAL GDO GARAGE DOOR OPENER LL C/) W
<br /> BREAKERS OR SPACE OR EQUIVALENT MULTI-POLE ARRANGEMENT, OR FRACTION
<br /> 2. COORDINATE THE LOCATION OF THE TRENCHES AND CONDUITS FOR ELECTRICAL AND
<br /> THEREOF, BUT NOT LESS THAN TWO CONDUITS FOR EACH PANEL. 2. TIME SWITCHES SHALL BE EQUAL TO PARAGON,GENERAL ELECTRIC, TORK, OR CONDUIT ROUTED UNDERFLOOR / UNDERGROUND OS OCCUPANCY SENSOR(DUAL-TECHNOLOGY TYPE UNO) Z
<br /> INTERMATIC AND SHALL HAVE SIZE AND NUMBER OF POLES AS REQUIRED.
<br /> TELEPHONE UTILITY SERVICES WITH THE GENERAL CONTRACTOR. 6. PANEL BOARDS TO BE PROVIDED WITH COPPER BUSSING ONLY. # Q \,
<br /> RACEWAY W/ 12 CONDUCTORS UNO RECESSED EXHAUST FAN Z �r
<br /> 0 3. COORDINATE HVAC EQUIPMENT CONNECTION REQUIREMENTS WITH HVAC CONTRACTOR. 3. PHOTOCELLS SHALL BE EQUAL TO TORK OR INTERMATIC WITH VOLTAGE AS INDICATED. LUV
<br /> Z 1. LOAD CENTERS SHALL NOT BE ALLOWED UNLESS NOTED OTHERWISE. W
<br /> RACEWAY TURNED UP ••• DOOR CHIME '�.J
<br /> Frozen Yogurt,Ice-Cream and More..
<br /> Z PART II - PRODUCTS AND EXECUTION 6. ALL NEW PANELBOARD5 SHALL COMPLY WITH NEC ARTICLE 110.16. EQUIPMENT
<br /> NOTE: NOT ALL SYMBOLS .
<br /> 0 MANUFACTURERS SHALL PROVIDE WARNING LABELS FOR ALL PANELBOARD5, M. RECORD AND AS-BUILT DRAWINGS RACEWAY TURNED DOWN CONTACT (NORMALLY OPEN) MAY BE USED
<br /> Z A. MATERIALS GENERATORS, AUTOMATIC TRANSFER SWITCHES, ETC TO WARN QUALIFIED PERSONS OF 1. THE ELECTRICAL CONTRACTOR SHALL MAINTAIN A SET OF DRAWINGS AT THE JOB SITE HOMERUN TO PANELBOARp I/2"C W/3.12 CONDUCTORS UNO CONTACT (NORMALLY CLOSED)
<br /> POTENTIAL ELECTRIC ARC FLASH HAZARDS. THE MARKING SHALL BE LOCATED SO AS FOR THE EXCLUSIVE PURPOSE OF MAINTAINING A RECORD OF ALL WORK INSTALLED
<br /> w I. ALL MATERIALS SHALL BE NEW AND OF QUALITY AS SPECIFIED ON THE PLANS OR TO BE CLEARLY VISIBLE TO QUALIFIED PERSONS BEFORE EXAMINATION, ADJUSTMENT, AND TO SHOW ANY DEVIATIONS FROM THE WORK INDICATED ON THE DRAWINGS. ROFESS/
<br /> C SPECIFICATIONS AND MUST CARRY THE UNDERWRITER'S LABORATORIES APPROVAL SERVICE, OR MAINTENANCE OF THE EQUIPMENT. GAP-OFF TIME SWITCH ape ppHER ONq� DATE 11 /6/2020
<br /> Z
<br /> COVEREQUIRING
<br /> THE PURPOSE
<br /> FOR WHICH THEY ARE USED, IN
<br /> RENT APPLICABLE CODES AND REGULATIONS.
<br /> ADDITION MEETING ALL 2. AT THE COMPLETION OF THE PROJECT, ONE SET OF REPRODUCIBLE DRAWINGS, SHOWING
<br /> ALL A5-5UILT CONDITIONS, SHALL BE DELIVERED TO THE OWNER FOR ACCEPTANCE SCALE NOTED
<br /> E 18921 rn
<br /> ° B. CONDUIT
<br /> PRIOR TO FINAL PAYMENT. LLJ
<br /> Exp. 12/31/21 DRAWN AE
<br /> • I. ALL WIRING SHALL BE INSTALLED IN LISTED METALLIC CONDUIT EXCEPT AS PERMITTED
<br /> 0 BELOW. RG5, WITH A 20 MIL PVC COATING WILL BE USED WHEN IN CONTACT WITH EARTH. `p \1"">'
<br /> IMC MAY BE USED IN INDOOR LOCATIONS NOT IN CONTACT WITH THE EARTH. EMT MAYgTFJOB # 2013
<br /> z BE USED IN INDOOR LOCATIONS NOT IN CONTACT WITH EARTH,NOT IN CONCRETE 5LAB5 SHEET INDEX �F CA��FO�
<br /> J OR WALLS AND NOT SUBJECT TO DAMAGE. PVC MAY BE USED IN OR BELOW CONCRETE 11/06/20 SHEET NO.
<br /> D AND DIRECT BURIED IN EARTH. FLEXIBLE STEEL CONDUIT SHALL BE USED FOR INDOOR SHEET TITLE
<br /> z FINAL CONNECTIONS TO EQUIPMENT IN LENGTHS NOT TO EXCEED 12". LIQUID-TIGHT AUNG ENGINEERS
<br /> FLEXIBLE STEEL CONDUIT SHALL BE FOR OUTDOOR FINAL CONNECTIONS TO EQUIPMENT • EO.1 Electrical Specifications and Le end z,_
<br /> NOT TO EXCEED 36". • EO.2 Electrical Schedule HVAC . Electrical . Plumbing . Energy
<br /> U • EO.3 Electrical Diagrams and Schedules 7111 Garden Grove Blvd,Suite 108
<br /> o 0EO.4 Lighting Title 24 Garden Grove,CA 92841 1
<br /> o • E1.1 Electrical Li tin Plan Ph:(714)349-9181 EOO
<br /> z
<br /> • E1.2 Electrical Power n Email:info@aungengineers.com
<br /> o Web :www.aungengineers.com
<br />
|