Laserfiche WebLink
FLASH POINT LEL UEL FLAMMABILITY CLASSIFICATION <br />Not Applicable Not Not Not Applicable <br />CarbonApplicable Applicable EXTINGUISHING MEDIA <br />UNUSUAL <br />0°oxide, Dry Chemical, Foam <br />SUAL FIRE AND EXPLOSION HAZARDS <br />Dust at suffici <br />During ent concentrations can form explosive mixtures with air. <br />emergency conditions overexposure to decomposition products may cause a health hazard. Symptoms may not be Immediately <br />apparent• Obtain medical attention. <br />SPECIAL FIRE FIGHTING PROCEDURES <br />Full protective equipment including self-contained breathing apparatus should be used. <br />Water spray may be ineffective. If water is used, fog nozzles are preferable. Water may be used to cool closed containers to prevent pressure <br />build-up and possible autoignition or explosion when exposed to extreme heat. <br />SECTION 6—ACCIDENTAL RELEASE MEASURES <br />STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED <br />Remove all sources of ignition. Ventilate the area. <br />Sweep up material taking care not to generate airborne dust. <br />SECTION 7 -- HANDLWG AND STORAGE <br />STORAGE CATEGORY <br />Not Applicable <br />PRECAUTIONS TO BETAKEN IN HANDLING AND STORAGE <br />Store in a cool, dry area out of direct sunlight. <br />Keep container closed when not in use. Transfer only to approved containers with complete and appropriate labeling. Do not take intemally. <br />Keep cut of the reach of children. <br />SECTION 8 — EXPOSf1RE CONTROLSIPERSONAL PROTECTION <br />PRECAUTIONS TO BE TAKEN IN USE <br />Use only with adequate ventilation. <br />Avoid eye and prolonged skin contact with dust. Avoid generating or breathing airborne dust. <br />Wash hands after using. <br />This coating may contain materials classified as nuisance particulates (listed "as Dust' in Section 2) which may be present at hazardous <br />levels only during sanding or abrading of the dried film. If no specific dusts are listed in Section 2, the applicable limits for nuisance dusts <br />are ACGIH TLV 10 mg/m3 (total dust), 3 mg/m3 (respirable fraction), OSHA PEL 15 mg/m3 (total dust), 5 mg/m3 (respirable fraction). <br />VENTILATION <br />Local exhaust preferable. General exhaust acceptable if the exposure to materials in Seclien 2 is maintained below applicable exposure <br />limits. Refer to OSHA Standards 1910.94, 1910.107, 1910.108. <br />RESPIRATORY PROTECTION <br />If personal exposure cannot be controlled below applicable limits by ventilation, wear a properly fitted organic vapor/particulate respirator <br />approved by NIOSHIMSHA for protection against materials In Section 2. <br />When sanding or abrading the dried film, wear a dust/mist respirator approved by NIOSHIMSHA for dust which may be generated from this <br />product, underlying paint, or the abrasive. <br />PROTECTIVE GLOVES <br />Required for long or repeated contact. <br />EYE PROTECTION <br />Wear safety spectacles with unperforated sldeshieids. <br />SECTION 9 —PHYSICAL AND CHEMICAL PROPERTIES <br />PRODUCT WEIGHT 11.8611b1gal 1421 gig <br />SPECIFIC GRAVITY 1.43 <br />BOILING POINT Not <br />Applicable <br />MELTING POINT Not Available <br />VOLATILE VOLUME 0% <br />EVAPORATION RATE NolAvailable <br />VAPOR DENSITY NotAvallable <br />SOLUBILITY IN WATER Not Available <br />VOLATILE ORGANIC COMPOUNDS (VOC Theoretical - As Packaged) <br />0.00 lblgal 0 gA Less Water and Federally Exempt Solvents <br />0.00 Iblgal 0 gA Emilted VOC <br />page 2 of 4 <br />