|
SINGLE USER SIZE: DRINKING FOUNTAIN NOTES
<br /> 1. NO FEWER THAN TWO DRINKING FOUNTAINS SHALL BE PROVIDED. WHEN PROVIDED, ONE LOWERED
<br /> 1. CLEARANCE AROUND A WATER CLOSET SHALL BE 60 INCHES MINIMUM MEASURED PERPENDICULAR FROM DRINKING FOUNTAIN AND ONE DRINKING FOUNTAIN FOR STANDING PERSONS SHALL BE PROVIDED.
<br /> THE SIDE WALL AND 56 INCHES MINIMUM MEASURED PERPENDICULAR FROM THE REAR WALL. A MINIMUM 60 2. WHERE A SINGLE DRINKING FOUNTAIN FOR STANDING AND SEATING PERSONS IS PROVIDED, IT
<br /> INCHES WIDE AND 48 INCHES DEEP MANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE WATER SHALL BE PERMITTED TO BE SUBSTITUTED FOR TWO SEPARATE DRINKING FOUNTAINS.
<br /> CLOSET. 3. UNITS SHALL HAVE A CLEAR FLOOR OR GROUND SPACE POSITIONED FOR A FORWARD APPROACH
<br /> 59" MIN. 59" MIN. AND CENTERED ON THE UNIT. y
<br /> FLOOR MOUNTED W FLOOR MOUNTED W TOILET COMPARTMENT SIZE: P T
<br /> 56" MIN. 56" MIN. 4. KNEE AND TOE CLEARANCE SHALL BE PROVIDED. Id N o
<br /> t6" MIN. 36 MIN. 1. WHEELCHAIR ACCESSIBLE COMPARTMENTS SHALL BE 60 INCHES WIDE MINIMUM MEASURED PERPENDICULAR 8"-19" 5. OPERABLE PARTS SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, C7 0co
<br /> 0 WALL MOUNTED WC ® WALL MOUNTED WC TO THE SIDE WALL, AND 56 INCHES DEEP MINIMUM FOR WALL HUNG WATER CLOSETS AND 59 INCHES DEEP PINCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE OPERABLE PARTS ` ir. CD ti coo
<br /> MINIMUM FOR FLOOR MOUNTED WATER CLOSETS MEASURED PERPENDICULAR TO THE REAR WALL. 5" MAX. SHALL BE 5 POUNDS. THE FLOW OF WATER SHALL BE ACTIVATED BY A MANUALLY OPERATED w
<br /> j 2. IN A WHEELCHAIR ACCESSIBLE COMPARTMENT WITH AN IN-SWINGING DOOR, A MINIMUM 60 INCHES WIDE BY 15" MIN. SYSTEM THAT IS FRONT MOUNTED OR SIDE MOUNTED AND LOCATED WITHIN 6 INCHES OF THE CD ~ ti
<br /> 36 INCHES DEEP MANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE REQUIRED WC CLEARANCE. FRONT EDGE OF THE FOUNTAIN OR AN AUTOMATIC ELECTRONICALLY CONTROLLED DEVICE. i� }' 0 6'
<br /> 3. IN A WHEELCHAIR ACCESSIBLE COMPARTMENT WITH A DOOR LOCATED IN THE SIDE WALL OR PARTITION, 6. SPOUT OUTLETS SHALL BE 36 INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND. W Q EEITHER IN-SWINGING OR OUT-SWINGING, A MINIMUM 60 INCHES WIDE AND 60 INCHES DEEP MANEUVERING 7. THE SPOUT SHALL BE LOCATED 15 INCHES MINIMUM FROM THE VERTICAL SUPPORT AND 5 INCHESSPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET. v cn o 0 60" MIN. b 4. IN A WHEELCHAIR ACCESSIBLE COMPARTMENT WITH A DOOR LOCATED IN THE FRONT WALL OR PARTITION MAXIMUM FROM THE FRONT EDGE OF THE UNIT, INCLUDING BUMPERS. w ) o
<br /> (FACING THE WATER CLOSET), EITHER IN-SWINGING OR OUT-SWINGING, A MINIMUM 60 INCHES WIDE AND 48 8. THE SPOUT SHALL PROVIDE A FLOW OF WATER 4 INCHES HIGH MINIMUM AND SHALL BE LOCATED 5 X oco
<br /> INCHES DEEP MANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET X INCHES MAXIMUM FROM THE FRONT OF THE UNIT. THE ANGLE OF THE WATER STREAM SHALL BE O v C2 C
<br /> o Q MEASURED HORIZONTALLY RELATIVE TO THE FRONT FACE OF THE UNIT. WHERE SPOUTS ARE m
<br /> 60" MIN. TOILET COMPARTMENT DOORS: LOCATED LESS THAN 3 INCHES OF THE FRONT OF THE UNIT, THE ANGLE OF THE WATER STREAM o ti
<br /> 8" MIN4 SHALL BE 30 DEGREES MAXIMUM. WHERE SPOUTS ARE LOCATED BETWEEN 3 INCHES AND 5 INCHES � 6'
<br /> 1. TOILET COMPARTMENT DOORS, INCLUDING DOOR HARDWARE, SHALL COMPLY WITH SECTION 11B-404 EXCEPT MAXIMUM FROM THE FRONT OF THE UNIT, THE ANGLE OF THE WATER STREAM SHALL BE 15 `0 °J
<br /> THAT IF THE APPROACH IS FROM THE PUSH SIDE OF THE COMPARTMENT DOOR, CLEARANCE BETWEEN THE DEGREES MAXIMUM.
<br /> - DOOR SIDE OF THE COMPARTMENT AND ANY OBSTRUCTION SHALL BE 48 INCHES MINIMUM MEASURED
<br /> SIZE OF CLEARANCE SIDE OUT-SWINGING SIDE IN-SWINGING DOOR PERPENDICULAR TO THE COMPARTMENT DOOR IN ITS CLOSED POSITION. 9. SPOUT OUTLETS OF DRINKING FOUNTAINS FOR STANDING PERSONS SHALL BE 38 INCHES MINIMUM
<br /> AT WATER CLOSETS DOOR 2. DOORS SHALL BE LOCATED IN THE FRONT PARTITION OR IN THE SIDE WALL OR PARTITION FARTHEST FROM AND 43 INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND.
<br /> THE WATER CLOSET. 10. WALL AND POST MOUNTED CANTILEVERED DRINKING FOUNTAINS SHALL BE 18 INCHES MINIMUM AND
<br /> 3. WHERE LOCATED IN THE FRONT PARTITION, THE DOOR OPENING SHALL BE 4 INCHES MAXIMUM FROM THE 19 INCHES MAXIMUM IN DEPTH.
<br /> SIDE WALL OR PARTITION FARTHEST FROM THE WATER CLOSET. WHERE LOCATED IN THE SIDE WALL OR 11. ALL DRINKING FOUNTAINS SHALL EITHER BE LOCATED COMPLETELY WITHIN ALCOVES, POSITIONED
<br /> 59" MIN. 59" MIN. PARTITION, THE DOOR OPENING SHALL BE 4 INCHES MAXIMUM FROM THE FRONT PARTITION. DRINKING FOUNTAIN DRINKING FOUNTAIN COMPLETELY BETWEEN WING WALLS, OR OTHERWISE POSITIONED SO AS NOT TO ENCROACH INTO
<br /> FLOOR MOUNTED W FLOOR MOUNTED W 4. THE DOOR SHALL BE SELF-CLOSING. SPOUT LOCATION ELEVATION PEDESTRIAN WAYS. THE PROTECTED AREA WITHIN WHICH A DRINKING FOUNTAIN IS LOCATED SHALL
<br /> 5. A DOOR PULL COMPLYING WITH SECTION 11B-404.2.7 SHALL BE PLACED ON BOTH SIDES OF THE DOOR BE 32 INCHES WIDE MINIMUM AND 18 INCHES DEEP MINIMUM. ALCOVES SHALL BE 36 INCHES WIDE Store:
<br /> 56" MIN. 56" MIN. » NEAR THE LATCH.
<br /> 0 WALL MOUNTED WC WALL WALL MOUNTED WC 36 MIN 6. DOORS SHALL NOT SWING INTO THE CLEAR FLOOR SPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE. MINIMUM WHERE THE DEPTH EXCEEDS 24 INCHES. WHEN USED, WING WALLS OR BARRIERS SHALL 1311 E. YOSEMITE AVE.
<br /> • DOORS MAY SWING INTO THAT PORTION OF MANEUVERING SPACE WHICH DOES NOT OVERLAP THE PROJECT HORIZONTALLY AT LEAST AS FAR AS THE DRINKING FOUNTAIN AND TO WITHIN 6 INCHES
<br /> VERTICALLY FROM THE FLOOR OR GROUND SURFACE.
<br /> ALTERNATE CLEARANCE REQUIRED AT A WATER CLOSET. N.T.S.
<br /> DOOR 7. WHEN LOCATED AT THE SIDE OF A TOILET COMPARTMENT, THE TOILET COMPARTMENT DOOR OPENING SHALL DRINKING FOUNTAINS CA-11B-602 4 MANTECA, CA 95336
<br /> Z O Z O LOCATION PROVIDE A CLEAR WIDTH OF 34 INCHES MINIMUM. 07.01.1
<br /> � � TOE CLEARANCE: 8" MIN.
<br /> Restaurant #RC529
<br /> 0 0 -
<br /> 1/2- MIN.
<br /> OOR PERMITTED / 1. AT LEAST ONE SIDE PARTITION SHALL PROVIDE A TOE CLEARANCE OF 9 INCHES MINIMUM ABOVE THE F.O.F. 1/2" MIN.
<br /> TO SWING OVER �___ FINISH FLOOR AND 6 INCHES DEEP MINIMUM BEYOND THE COMPARTMENT-SIDE FACE OF THE PARTITION, z " Professional of Record: NAME
<br /> HATCHED --- " MAX. EXCLUSIVE OF PARTITION SUPPORT MEMBERS. PARTITION COMPONENTS AT TOE CLEARANCES SHALL BE 9 MAX.
<br /> PORTION OF 4" MAX. SMOOTH WITHOUT SHARP EDGES OR ABRASIVE SURFACES.
<br /> 48" MIN 48" MIN MANEUVERING 2. COMPARTMENTS FOR CHILDREN'S USE SHALL PROVIDE A TOE CLEARANCE OF 12 INCHES MINIMUM ABOVE o0 ? L7
<br /> THE FINISH FLOOR.
<br /> 3. TOE CLEARANCE AT THE SIDE PARTITION IS NOT REQUIRED IN A COMPARTMENT GREATER THAN 66 INCHES
<br /> WIDE. Q z o
<br /> END OUT-SWINGING END IN-SWINGING DOOR TOILET COMPARTMENT NSU LATE
<br /> DESIGN
<br /> DOOR DOORS AMBULATORY ACCESSIBLE COMPARTMENTS: PIPES ^00 x
<br /> EQUIRED CLEAR SPACE Q
<br /> 1. AMBULATORY ACCESSIBLE COMPARTMENTS SHALL HAVE A DEPTH OF 60 INCHES MINIMUM AND A WIDTH OF
<br /> F.O.F.
<br /> 35 INCHES MINIMUM AND 37 INCHES MAXIMUM. - A r c h i t e c t u r a l
<br /> 2. TOILET COMPARTMENT DOORS, INCLUDING DOOR HARDWARE, SHALL COMPLY WITH SECTION 1113-404, EXCEPT LAVATORY ELEVATION Solutions I u t i o n s Gro u
<br /> PARTITION ARTITION THAT IF THE APPROACH IS TO THE LATCH SIDE OF THE COMPARTMENT DOOR, CLEARANCE BETWEEN THE LAVATORY CLEAR p
<br /> O z O DOOR SIDE OF THE COMPARTMENT AND ANY OBSTRUCTION SHALL BE 44 INCHES MINIMUM. THE DOOR LAVATORY NOTES: SPACE38 EXECUTIVE PARK,
<br /> SHALL BE SELF-CLOSING. A DOOR PULL COMPLYING WITH SECTION 11B-404.2.7 SHALL BE PLACED ON WALL HUNG TYPE STALL TYPE SUITE 310
<br /> " MIN. " MIN. - BOTH SIDES OF THE DOOR NEAR THE LATCH. TOILET COMPARTMENT DOORS SHALL NOT SWING INTO THE 1. A CLEAR FLOOR SPACE POSITIONED FOR A FORWARD APPROACH, AND URINAL NOTES: IRVINE, CA 92614
<br /> o MINIMUM REQUIRED COMPARTMENT AREA. KNEE AND TOE CLEARANCE SHALL BE PROVIDED. CONTACT: JEFF LIEDERMAN
<br /> 2. THE DIP OF THE OVERFLOW SHALL NOT BE CONSIDERED IN DETERMINING 1. URINALS SHALL BE THE STALL-TYPE OR THE WALL-HUNG TYPE WITH (949) 430-7051
<br /> OVERLAP: KNEE AND TOE CLEARANCES. THE RIM 17 INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND. JLIEDERMAN@PMDGINC.COM
<br /> 3. LAVATORIES AND SINKS SHALL BE INSTALLED WITH THE FRONT OF THE 2. URINALS SHALL BE 13-1/2 INCHES MINIMUM MEASURED FROM THE
<br /> 9" MIN. 12" MIN. 1. THE REQUIRED CLEARANCE AROUND THE WATER CLOSET SHALL BE PERMITTED TO OVERLAP THE WATER HIGHER OF THE RIM OR COUNTER SURFACE 34 INCHES MAXIMUM ABOVE OUTER FACE OF THE URINAL RIM TO THE BACK OF THE FIXTURE.
<br /> z CLOSET, ASSOCIATED GRAB BARS, DISPENSERS, SANITARY NAPKIN DISPOSAL UNITS, COAT HOOKS, SHELVES, THE FINISH FLOOR OR GROUND. 3. A CLEAR FLOOR OR GROUND SPACE POSITIONED FOR FORWARD
<br /> ACCESSIBLE ROUTES, CLEAR FLOOR SPACE AND CLEARANCES REQUIRED AT OTHER FIXTURES, AND THE 4. CONTROLS FOR FAUCETS SHALL BE OPERABLE WITH ONE HAND AND APPROACH SHALL BE PROVIDED.
<br /> TURNING SPACE. NO OTHER FIXTURES OR OBSTRUCTIONS SHALL BE LOCATED WITHIN THE REQUIRED WATER SHALL NOT REQUIRE TIGHT GRASPING PINCHING OR TWISTING OF THE 4. FLUSH CONTROLS SHALL BE HAND OPERATED OR AUTOMATIC. HAND
<br /> ELEVATION ELEVATION -- CLOSET CLEARANCE. WRIST. THE FORCE REQUIRED TO ACTIVATE OPERABLE PARTS SHALL BE 5 OPERATED FLUSH CONTROLS SHALL BE OPERABLE WITH ONE HAND
<br /> 6" MIN. ADULT CHILDREN POUNDS. HAND-OPERATED METERING FAUCETS SHALL REMAIN OPEN FOR AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF
<br /> WATER CLOSET: THE WRIST. THE FORCE REQUIRED TO ACTIVATE OPERABLE PARTS
<br /> 10 SECONDS MINIMUM.
<br /> 5. WATER SUPPLY AND DRAIN PIPES UNDER LAVATORIES AND SINKS SHALL SHALL BE 5 POUNDS.
<br /> TOE CLEARANCE TOE CLEARANCE AMBULATORY 1. THE WATER CLOSET SHALL BE POSITIONED WITH A WALL OR PARTITION TO THE REAR AND TO ONE SIDE. BE INSULATED OR OTHERWISE CONFIGURED TO PROTECT AGAINST 5. THE FLUSH CONTROL SHALL BE MOUNTED AT A MAXIMUM HEIGHT OF
<br /> COMPARTMENT THE CENTERLINE OF THE WATER CLOSET SHALL BE 17 INCHES MINIMUM TO 18 INCHES MAXIMUM FROM THE CONTACT. THERE SHALL BE NO SHARP OR ABRASIVE SURFACES UNDER 44 INCHES ABOVE THE FINISH FLOOR.
<br /> SIDE WALL OR PARTITION, EXCEPT THAT THE WATER CLOSET SHALL BE 17 INCHES MINIMUM AND 19 INCHES LAVATORIES AND SINKS.
<br /> MAXIMUM FROM THE SIDE WALL OR PARTITION IN THE AMBULATORY ACCESSIBLE TOILET COMPARTMENT.
<br /> SHALL BE A MINIMUM OF 18 INCHES TO THE CENTERLINE OF NTIJ%.FIXTU E. N.T.S. RC
<br /> 8c 2. THE SEAT HEIGHT OF A WATER CLOSET ABOVE THE FINISH FLOOR SHALL BE 17 INCHES MINIMHT -AND
<br /> TOILET ROOMS C 0 M P A R TM E N TS 9 TF
<br /> INCHES MAXIMUM MEASURED TO THE TOP OF THE SEAT. SEATS SHALL NOT BE SPRUN Ag1CB-R Tljf�pd60 o Al 1 LAVATORIES CA-11B-606 7 URINALS CA-11B-605 3 Y S,
<br /> LIFTED POSITION. SEATS SHALL BE 2 INCHES HIGH MAXIMUM. 07.0,., 07.01.107.01.1ED-Ro0N
<br /> CLEAR SPACE �
<br /> GRAB BAR NOTES: 1. REQUIRED CLEAR FLOOR SPACES, CLEARANCE AT FIXTURES, AND TURNING C-29534
<br /> SPACE SHALL BE PERMITTED TO OVERLAP. N°' 2p2A Q
<br /> " 1. GRAB BARS SHALL BE PROVIDED ON THE SIDE WALL CLOSEST TO 7"-9" 2. DOORS SHALL NOT SWING INTO THE CLEAR FLOOR SPACE OR CLEARANCE PR• 3�' oP1E _
<br /> 4 MIN. THE WATER CLOSET AND ON THE REAR WALL. REQUIRED FOR ANY FIXTURE. sT PRENEwP� o�
<br /> 2" MAX. 2. THE SIDE WALL GRAB BAR SHALL BE 42 INCHES LONG MINIMUM, 3. WHERE
<br /> X 48E INCH ET ROOM
<br /> FLOOR SPACE IS PROVIDED IS FOR INDIVIDUALN THE USE ANDA 30 9�F o F
<br /> 2" MIN. EXTENDING 54 INCHES MINIMUM FROM THE REAR WALL WITH THE LOCATED 12 INCHES MAXIMUM FROM THE REAR WALL AND ❑ THE ARC OF THE DOOR SWING, DOORS SHALL BE PERMITTED TO SWING INTO THE
<br /> FRONT END POSITIONED 24 INCHES MINIMUM IN FRONT OF THE a, z CLEAR FLOOR SPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE Prototype : P4 EXTENDED- HV, SCHEME A
<br /> 4" MIN WATER CLOSET.
<br /> 3. THE REAR WALL GRAB BAR SHALL BE 36 INCHES LONG MINIMUM TOILET ROOM ACCESSORIES
<br /> AND EXTEND FROM THE CENTERLINE OF THE WATER CLOSET 12 1. MIRRORS LOCATED ABOVE LAVATORIES OR COUNTERTOPS SHALL BE INSTALLED Prototype Issue Date: 6.29.2020
<br /> INCHES MINIMUM ON ONE SIDE AND 24 INCHES MINIMUM ON THE DISPENSER UNIT WITH THE BOTTOM EDGE OF THE REFLECTING SURFACE 40 INCHES MAXIMUM
<br /> OTHER SIDE. LOCATION ABOVE THE FINISH FLOOR OR GROUND. Design Bulletin Updates: INCLUDED
<br /> 2. MIRRORS NOT LOCATED ABOVE LAVATORIES OR COUNTERTOPS SHALL BE
<br /> M 4. THE REAR GRAB BAR SHALL BE PERMITTED TO BE 24 INCHES LONG
<br /> MINIMUM, CENTERED ON THE WATER CLOSET, WHERE WALL SPACE INSTALLED WITH THE BOTTOM EDGE OF THE REFLECTING SURFACE 35 INCHES Date Issued: Bulletin Number:
<br /> SIDE WALL GRAB BAR _ MAXIMUM ABOVE THE FINISH FLOOR OR GROUND.
<br /> N DOES NOT PERMIT A LENGTH OF 36 INCHES MINIMUM DUE TO THE 3. COAT HOOKS SHALL BE LOCATED WITHIN 48 INCHES MAXIMUM ABOVE THE FINISH NOV. 2018 1 & 2
<br /> LOCATION OF A RECESSED FIXTURE ADJACENT TO THE WATER FLOOR.
<br /> 1-1N. CLOSET. 4. SHELVES SHALL BE LOCATED 40 INCHES MINIMUM AND 48 INCHES MAXIMUM
<br /> " MIN. 5. GRAB BARS WITH CIRCULAR CROSS SECTIONS SHALL HAVE AN 1ST BLDG. SUBMITTAL
<br /> 36" MIN. ABOVE THE FINISH FLOOR. MEDICINE CABINETS SHALL BE LOCATED WITH A
<br /> OUTSIDE DIAMETER OF 1-1/4 INCHES MINIMUM AND 2 INCHES TO MIRROR
<br /> 24 MIN. 2 MIN. MAXIMUM. J SURFACE USABLE SHELF NO HIGHER THAN 44 INCHES MAXIMUM ABOVE THE FINISH FLOOR.
<br /> 6. THE SPACE BETWEEN THE WALL AND THE GRAB BAR SHALL BE o - °° 5. WHERE TOWEL OR SANITARY NAPKIN DISPENSERS, WASTE RECEPTACLES, OR
<br /> PROJECTING OBJECTS RECESSED OBJECTS 1-1/2 INCHES. THE SPACE BETWEEN THE GRAB BAR AND X OTHER ACCESSORIES ARE PROVIDED IN TOILET FACILITIES, AT LEAST ONE OF
<br /> 2 < EACH TYPE SHALL BE LOCATED ON AN ACCESSIBLE ROUTE. ALL OPERABLE
<br /> PROJECTING OBJECTS BELOW AND AT THE ENDS SHALL BE 1-1
<br /> INCHES MINIMUM. THE SPACE BETWEEN THE GRAB BAR AND / PARTS, INCLUDING COIN SLOTS, SHALL BE 40 INCHES MAXIMUM ABOVE THE
<br /> SPACING OF GRAB BARS PROJECTING OBJECTS ABOVE SHALL BE 12 INCHES MINIMUM. 0 FINISH FLOOR.
<br /> TRANSFER 7. GRAB BARS SHALL BE INSTALLED IN A HORIZONTAL POSITION, 33 6. TOILET PAPER DISPENSERS SHALL BE 7 INCHES MINIMUM AND 9 INCHES
<br /> INCHES MINIMUM AND 36 INCHES MAXIMUM ABOVE THE FINISH MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO THE CENTERLINE OF
<br /> SIDE FLOOR MEASURED TO THE TOP OF THE GRIPPING SURFACE. THE DISPENSER. THE OUTLET OF THE DISPENSER SHALL BE BELOW THE GRAB
<br /> 8. GRAB BARS AND ANY WALL OR OTHER SURFACES ADJACENT TO SEAT TOWEL WASTE PRODUCT TOWEL SOAP MIRROR BAR, 19 INCHES MINIMUM ABOVE THE FINISH FLOOR AND SHALL NOT BE
<br /> GRAB BARS SHALL BE FREE OF SHARP OR ABRASIVE ELEMENTS COVER & DISPENSER LOCATED BEHIND GRAB BARS. DISPENSERS SHALL NOT BE OF A TYPE THAT
<br /> CONTROLS DELIVERY OR THAT DOES NOT ALLOW CONTINUOUS PAPER FLOW.
<br /> AND SHALL HAVE ROUNDED EDGES. DISPENSER WASTE
<br /> 7. SANITARY NAPKIN DISPOSAL UNITS, IF PROVIDED, SHALL COMPLY WITH SECTION REVISIONS:
<br /> REAR WALL GRAB BAR 9. GRAB BARS SHALL NOT ROTATE WITHIN THEIR FITTINGS.
<br /> 10. GRAB BARS SHALL BE INSTALLED IN ANY MANNER THAT PROVIDES TOILET ROOM 11B-309.4 AND SHALL BE WALL MOUNTED AND LOCATED ON THE SIDEWALL 1 08-07-20 1st. Bldg. Submittal
<br /> ACCESSORIES BETWEEN THE REAR WALL OF THE TOILET AND THE TOILET PAPER DISPENSER,
<br /> DOES NOT OBSTRUCT THE REQUIRED CLEAR FLOORS ACE. T LOCATED BELOW THE GRAB BAR WITH THE OPENING OF TH DISR0318., UNIT 1 2
<br /> WATER CLOSET GRAB BARS 11. ALLOWABLE STRESSES SHALL NOT BE EXCEEDED FOR 10 TOILET ROOM ACCESSORIESTOE 8c KNEE CLEARANCEINCHES MINIMUM ABOVE THE FINISH FLOOR CA-11B-603, 11B-604 3
<br /> USED WHEN A VERTICAL OR HORIZONTAL FORCE OF 1 I�ld���091 0701, 4
<br /> APPLIED AT ANY POINT ON THE GRAB BAR, FASTENER, MOUNTING
<br /> DEVICE, OR SUPPORTING STRUCTURE. TOE CLEARANCE AT 9 INCHES ABOVE THE FINISH FLOOR OR GROUND, 5
<br /> 1. SPACE UNDER AN ELEMENT BETWEEN THE FINISH AND 8 INCHES DEEP MINIMUM AT 27 INCHES ABOVE 6
<br /> FLOOR OR GROUND AND 9 INCHES ABOVE THE FINISH THE FINISH FLOOR OR GROUND. 7
<br /> z FLOOR OR GROUND SHALL BE CONSIDERED TOE 4. BETWEFINISHEN 9 FLOOR ORES AND 7
<br /> INCHES ABOVE THE
<br /> GROUND, THE KNEE CLEARANCE 8
<br /> CLEARANCE. SHALL BE PERMITTED TO REDUCE AT A RATE OF 1
<br /> 2. TOE CLEARANCE SHALL EXTEND 25 INCHES MAXIMUM 9
<br /> 9" 0 UNDER AN ELEMENT. INCH IN DEPTH FOR EACH 6 INCHES IN HEIGHT.
<br /> MIN. 3. WHERE TOE CLEARANCE IS REQUIRED AT AN ELEMENT 5. KNEE CLEARANCE SHALL BE 30 INCHES WIDE
<br /> AS PART OF A CLEAR FLOOR SPACE, THE TOE MINIMUM.
<br /> 6" MAX. 17"-25" CLEARANCE SHALL EXTEND 17 INCHES MINIMUM
<br /> UNDER THE ELEMENT. ADDITIONAL LAVATORY CLEARANCE Sheet Title:
<br /> ELEVATION PLAN 4. THE TOE CLEARANCE SHALL EXTEND 19 INCHES
<br /> MINIMUM UNDER SINKS REQUIRED TO BE ACCESSIBLE. 1. TOE CLEARANCE SHALL EXTEND 19 INCHES MAXIMUM
<br /> TOE CLEARANCE 5. SPACE EXTENDING GREATER THAN 6 INCHES BEYOND UNDER LAVATORIES REQUIRED TO BE ACCESSIBLE. ACCESSIBILITY
<br /> THE AVAILABLE KNEE CLEARANCE AT 9 INCHES 2. AT LAVATORIES REQUIRED TO BE ACCESSIBLE SPACE
<br /> ABOVE THE FINISH FLOOR OR GROUND SHALL NOT BE BETWEEN 9 INCHES AND 29 INCHES ABOVE THE DETAILS
<br /> CONSIDERED TOE CLEARANCE. FINISH FLOOR OR GROUND, SHALL BE CONSIDERED
<br /> 8" MIN. z 8" MIN. z 6. TOE CLEARANCE SHALL BE 30 INCHES WIDE MINIMUM. KNEE CLEARANCE. Date: 08.07.2020
<br /> 3. AT LAVATORIES REQUIRED TO BE ACCESSIBLE, THE
<br /> KNEE CLEARANCE KNEE CLEARANCE SHALL BE 27 INCHES HIGH MINIMUM Project Number: RAC19024.0
<br /> z 0) z_ z_ z ABOVE THE FINISH FLOOR OR GROUND AT A DEPTH
<br /> 1. SPACE UNDER AN ELEMENT BETWEEN 9 INCHES AND
<br /> 27 INCHES ABOVE THE FINISH FLOOR OR GROUND OF 8 INCHES MINIMUM INCREASING TO 29 INCHES Drawn B :
<br /> o SHALL BE CONSIDERED KNEE CLEARANCE.V0 4
<br /> HIGH MINIMUM ABOVE THE FINISH FLOOR OR GROUND y XXX/XXXX
<br /> 2. KNEE CLEARANCE SHALL EXTEND 25 INCHES MAXIMUM AT THE FRONT EDGE OF A COUNTER WITH ABUILT-IN
<br /> LAVATORY OR AT THE FRONT EDGE OF A
<br /> 25" UNDER AN ELEMENT AT 9 INCHES ABOVE THE FINISH
<br /> FLOOR OR GROUND.
<br /> MAX. WALL-MOUNTED LAVATORY FIXTURE.
<br /> 11" MIN. 11" MIN. 3. WHERE KNEE CLEARANCE IS REQUIRED UNDER AN ADDITIONAL DINING &WORK SURFACE CLEARANCE Sheet Number:
<br /> ELEVATION PLAN ELEVATION AT LAVATORY ELEMENT AS PART OF A CLEAR FLOOR SPACE, THE
<br /> KNEE CLEARANCE SHALL BE 11 INCHES DEEP MINIMUM
<br /> 1. THE TOE CLEARANCE SHALL EXTEND 19 INCHES
<br /> KNEE CLEARANCE MINIMUM UNDER BUILT-IN DINING AND WORK
<br /> SURFACES REQUIRED TO BE ACCESSIBLE. AS
<br /> 3
<br /> 2. AT DINING AND WORK SURFACES REQUIRED TO BE
<br /> J
<br /> A I=Elk/�
<br /> INCHES DEEP MINIMUM AT 27 ll C&E$1•'Af%VE TH
<br /> TOE 8c KNEE CLEARANCE FINISH FLOOR OR GROUND. CA-11B-306
<br /> 3. THE KNEE CLEARANCE SHALL NOT BE REDU@C{) AT
<br />
|