|
E
<br /> PLUMBING NOTES PLUMBING KEYNOTES W Z =_
<br /> Z N
<br /> 1. DRAWINGS ARE DIAGRAMMATIC ONLY AND REPRESENT THE GENERAL SCOPE OF THE WORK. REVIEW u � 4)
<br /> THE GENERAL NOTES, SPECIFICATIONS AND PLANS FOR ADDITIONAL REQUIREMENTS THAT MAY NOT BE
<br /> SPECIFICALLY CALLED OUT IN THIS PORTION OF THE CONSTRUCTION DOCUMENTS. NOTIFY THE ;
<br /> ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES PRIOR TO SUBMISSION OF BID. To WATER E 4
<br /> ,13
<br /> METER
<br /> 2. PROVIDE A CONSTRUCTION RECORD SET OF "AS-BUILT" DOCUMENTS TO THE ARCHITECT REFLECTING (t 50 FT.) W a c
<br /> ANY VARIANCES OF INSTALLED PIPING LOCATIONS OR EQUIPMENT CONTRARY TO THE CONSTRUCTION
<br /> DOCUMENTS, REFER TO SPECIFICATIONS.
<br /> 3. PROVIDE TO THE ARCHITECT A COPY OF INSPECTION REPORTS AND APPROVAL CERTIFICATES FROM ;;
<br /> LOCAL AND STATE INSPECTIONS, REFER TO SPECIFICATIONS. �?
<br /> 4. INSTALLATION SHALL COMPLY WITH LEGALLY CONSTITUTED CODES AND THE REQUIREMENTS OF u)
<br /> AUTHORITIES HAVING JURISDICTION. o W
<br /> 5. PLANS AND SPECIFICATIONS GOVERN WHERE THEY EXCEED CODE REQUIREMENTS. w m
<br /> 6. VERIFY LOCATION AND DEPTH OF UTILITIES AT POINTS OF CONNECTION BEFORE START OF PIPING N
<br /> INSTALLATION. cm
<br /> UNDER THE COUNTERo I [9 U) N
<br /> 7. REFER TO ARCHITECTURAL PLANS FOR EXACT LOCATION AND MOUNTING HEIGHTS OF PLUMBING / w r £
<br /> FIXTURES. GREASE INTERCEPTOR
<br /> 8. DO NOT SCALE FLOOR PLANS FOR EXACT HORIZONTAL LOCATION OF PIPE ROUTING. _ a _ METER
<br /> 5❑ FT.) p 0
<br /> 9. INSTALL CONCEALED PIPING TIGHT TO THE STRUCTURE AND AS HIGH AS POSSIBLE. INSTALL
<br /> EXPOSED PIPING TIGHT TO THE STRUCTURE, WALL OR CEILING AND AS HIGH AS POSSIBLE. I I __ 0 £
<br /> COORDINATE WITH OTHER TRADES TO AVOID CONFLICTS. N I I I \ 0
<br /> 0
<br /> 10. VALVES SHALL BE LINE SIZE UNLESS OTHERWISE NOTED. cl LL T
<br /> 11. PIPING IN FINISHED AREAS SHALL BE ROUTED CONCEALED; EXPOSED PIPING, WHERE NECESSITY,
<br /> SHALL BE ROUTED AS HIGH AS POSSIBLE AND TIGHT TO WALLS.
<br /> 12. COORDINATE ALL WORK WITH OTHER TRADES AND CONTRACTORS. I I d
<br /> N
<br /> 13.000RDINATE PIPING INSTALLATION WITH STRUCTURAL GRADE BEAMS, FOOTINGS, COLUMN PIERS, ETC.
<br /> WHERE REQUIRED AND AS NOTED ON PLANS. COORDINATE SLEEVE INSTALLATIONS WITH THE ARCHITECT,
<br /> STRUCTURAL ENGINEER, STRUCTURAL CONTRACTOR AND GENERAL CONTRACTOR BEFORE CONCRETE IS
<br /> INSTALLED.
<br /> 14. CLEAN FAUCET AERATORS AND PIPE STAINERS PRIOR TO TURNING BUILDING OVER TO THE OWNER. w 0 1 6 w �, BUILDING DEPARTMENT
<br /> Z
<br /> 15. PROVIDE TRAP PRIMERS WHERE REQUIRED BY LOCAL AUTHORITIES. c� Q NAME:
<br /> 16. COORDINATE PIPING ROUTING AWAY FROM ELECTRICAL PANELS. DO NOT INSTALL PIPING OVER / CITY OF STOCKTON
<br /> ELECTRICAL PANELS. 3
<br /> 17. PAINT ALL EXPOSED GAS PIPING USING RUST INHIBITOR PIPING. PAINT AND COLOR SHALL BE / to U ADDRESS:
<br /> COORDINATED WITH THE ARCHITECT AND/OR OWNER. 0
<br /> 18. COORDINATE ALL ROOF PENETRATIONS WITH OTHER TRADES. MAINTAIN 10' MINIMUM CLEARANCE cn (n 425 N. ELDORADO ST.
<br /> FROM ALL AIR INTAKES. MAINTAIN 2' CLEARANCE FROM ALL OTHER EQUIPMENT. E2 STOCKTON, CA 95202
<br /> 3 G G G G
<br /> 19. INSULATE PIPING ROUTED IN EXTERIOR BUILDING WALLS WITH MINIMUM 2" BATT INSULATION TO PHONE:
<br /> PREVENT FREEZING.
<br /> 209-937-8561
<br /> 20. PROVIDE SHIELDED ADAPTER COUPLINGS FOR CONNECTION OF PVC DWV TO CAST IRON AT SLAB UNDER THE COUNTER
<br /> ON GRADE. SEE SPECIFICATION SECTION 15400 FOR MORE INFORMATION. N
<br /> 21. FLOW CONTROL VALVES SHALL BE SIZE 1/2" AND SET AT 0.5 GPM UNLESS NOTED OTHERWISE. GREASE INTERCEPTOR BUILDING OWNER
<br /> 3 3
<br /> 22. WATER HAMMER ARRESTORS SHALL BE SIZE "A" UNLESS NOTED OTHERWISE. NAME:
<br /> 23. PROVIDE VERTICAL LIFT SPRING LOADED CHECK VALVES IN HOT AND COLD WATER SUPPLIES FOR HW Hw
<br /> HW H 3-COMP SINK SHALL BECK PROPERTIES
<br /> MOP SINK FAUCETS DOWNSTREAM OF SHUTOFF VALVES. I ARCH HAVE AN INDIRECT LLI
<br /> 24. CORROSION PROTECTION / WRAPPING IS REQUIRED ON ALL UNDER SLAB OR UNDER GROUND CONNECTION TO THE Z ADDRESS:
<br /> FERROUS ELECTRICAL CONDUIT, WATER PIPING, BUILDING DRAINS, BUILDING SEWERS, FLOOR SINKS, PLUMBING FIXTURES TABLE3 MAIN WAIST LINE O 3114 W. HAMMER LN.
<br /> FLOOR DRAINS, TRAP PRIMERS, WASTE DRAINS, AND OTHER FERROUS PIPING, INCLUDING ALL ZINC
<br /> COATED GALVANIZED PIPING AND FITTINGS. CORROSION PROTECTION / WRAPPING IS REQUIRED ON (CA. PLUMBING CODE, TABLE: 4-1) STOCKTON, CA 95209
<br /> COPPER WATER PIPING. CORROSION PROTECTION SHALL BE INSPECTED AND APPROVED BY THE
<br /> BUILDING INSPECTOR BEFORE COVERING. TOTAL OCCUPANT LOAD = XXX PHONE:
<br /> 25. RELIEF VALVES LOCATED INSIDE A BUILDING SHALL BE PROVIDED WITH A DRAIN OF GALVANIZED /
<br /> STEEL, HARD DRAWN COPPER PIPING AND FITTINGS, CPVC, OR LISTED VALVE DRAIN. THE DRAIN SHALL W.C. W.C. UR. UR. LAV. LAV. D.F. D.F. (209) 957-0331
<br /> EXTEND FROM THE VALVE TO THE OUTSIDE OF THE BUILDING WITH THE END OF THE PIPE NOT MORE GENDER COUNT REQ'D PROV'D REQ'D PROV'D REQ'D PROV'D REQ'D PROV'D
<br /> THAN 2 FEET NOR LESS THAN 6 INCHES ABOVE THE GROUND AND POINTING DOWNWARD. (2016 CPC, 3 TENANT
<br /> SECTION 608.5) MALE XXX X X X X X X X X
<br /> 26. GAS UTILIZATION EQUIPMENT CONNECTED TO A PIPING SYSTEM SHALL HAVE AN ACCESSIBLE FEMALE XXX X X X X X X X X °TQ NAME:
<br /> APPROVED MANUAL SHUT OFF VALVE WITH A NON-DISPLACEABLE VALVE MEMBER, OR A LISTED GAS
<br /> CONVENIENCE OUTLET INSTALLED WITHIN 6' OF THE EQUIPMENT IT SERVES. SHUT OFF VALVES CD YUMMY DONUTS
<br /> SERVING DECORATIVE GAS APPLIANCES SHALL BE PERMITTED TO BE INSTALLED IN FIREPLACES IF Z
<br /> LISTED FOR SUCH USE. (2016 CPC, SECTION 1212.5) PIPING INDEX 3 z ADDRESS:
<br /> 27. WATER CLOSET BOWLS FOR PUBLIC USE SHALL BE OF THE ELONGATED TYPE. SEATS SHALL BE s s3221 W. HAMMER LN.
<br /> OF THE OPEN FRONT TYPE. CPC SECTION 403.1 W
<br /> E _ (E) ELECTRIC LINE (BURIED) e = (P) ELECTRIC LINE (BURIED) \ STOCKTON, CA 95209
<br /> 28. PUBLIC LAVATORIES SHALL HAVE TEMPERATURE CONTROLS WHICH LIMIT THE OUTLET TEMPERATURE
<br /> TO 110 DEGREES FAHRENHEIT. THE DEVICE SHALL CONFORM TO ASSE 1070 STANDARD FOR WATER O
<br /> O
<br /> TEMPERATURE LIMITING DEVICES OR CSA B125.3 STANDARD FOR PLUMBING FITTINGS. THE WATER w = (E) COLD WATER PIPE (TYPE-L COPPER) w = (P) COLD WATER PIPE (TYPE-L COPPER) ® ® Q
<br /> L L: PHONE:
<br /> HEATER THERMOSTAT SHALL NOT BE CONSIDERED A CONTROL.. CPC SECTION 413.1 a
<br /> z z
<br /> HW = (E) HOT WATER PIPE (TYPE-L COPPER) HW- = (P) HOT WATER PIPE (TYPE-L COPPER) O w O w( 209) 636-8909
<br /> 29. CHANGE IN DIRECTION OF THE DRAINAGE FLOW SHALL COMPLY WITH CPC, SECTION 706.0
<br /> c = (E) GAS LINE (SCHEDULE 40 METALLIC PIPE) G = (P) GAS LINE (SCHEDULE 40 METALLIC PIPE) O v� O v� LIC.
<br /> s = (E) (ABS/PVC) SEWER DRAIN PIPE s = (P) (ABS/PVC) SEWER DRAIN PIPE x CL X Tsi
<br /> Isi
<br /> GR = (E) (CAST IRON) GREASE DRAIN PIPE GR = (P) (CAST IRON) GREASE DRAIN PIPE 3 x x O NAME:
<br /> O O O O O O 0 T.B.D.
<br /> AR = (E) (PVC) DRAIN PIPE (ACID RESISTANT) AR = (P) (PVC) DRAIN PIPE (ACID RESISTANT) Q ADDRESS:
<br /> SCHEDULE - PLUMBING PIPING AND VALVES 3 0
<br /> O O O O O O C) PHONE:
<br /> KEYED NOTES: PIPE SIZE PIPE FITTINGS JOINTS INSULATION NOTES
<br /> (A) INSULATION IS REQUIRED FOR ALL ABOVE GROUND POTABLE WATER PIPING,
<br /> INCLUDING DOMESTIC COLD WATER, HOT WATER, AND HOT WATER RETURN. �V2 ¢� alb e(B) PAINT ALL EXPOSED EXTERIOR PIPING W/ ONE COAT OF PRIMER & /off 10 �� �� Q 40 J�4v ¢- ° o00 O QROFESS/pNq�
<br /> TWO COATS OF RUST-PROOF PAINT. m 0 G� ^h ^`� � � °i0 O4 J= ^:)
<br /> p
<br /> (C) PER FOOT MINIMUM SLOPE.
<br /> L j
<br /> (D) PER FOOT MINIMUM SLOPE. ��� �Jm �Jm $ ¢�% ¢�% ¢ ¢ OP Q �J p=ti ¢� �� p p2^ �o` �r� 4� v J� LLJ � No. C74034 z
<br /> e e v ¢ ? J J ¢ `` Z EXP.
<br /> (E) OR EQUAL 144
<br /> Gp Gp V ti� ti� 4v
<br /> o�
<br /> ¢4 m m o �, s �� 0 0 0 �o W OF c
<br /> 00 o�Q °¢� ° �¢ oe o� Q �¢ ¢_ ¢s a ``` Q �' o �`� �� 3� J=
<br /> V V C� C� . V O ¢ ., Z ¢ . O O Z J j C�
<br /> zP �`' �`' m =c, �� <' m oc, PHONE:
<br /> v v J� Jv Jv Jv Jv 3� O (� ^ (� S
<br /> z--) � �� �� J ¢ 209-263-1382
<br /> CONSTRUCTION SITE
<br /> UNDERGROUND SANITARY & GREASE WAIST & VENT LINES ALL SIZES (C) SITE ADDRESS:
<br /> ABOVEGROUND SANITARY & GREASE WAIST & VENT LINES ALL SIZES (C) a
<br /> 3221 W. HAMMER LN. STE.A&B
<br /> UNDERGROUND POTABLE WATER SERVICE ALL SIZES � • • ILJ�F z
<br /> Q STOCKTON, CA 95209
<br /> ABOVEGROUND POTABLE WATER LINES ALL SIZES (A)
<br /> Ld ABOVEGROUND LP GAS LINES ALL SIZES (B) QW
<br /> SITE APN:
<br /> TRAP PRIMER LINES ALL SIZES • • • (D) z 82-220-03
<br /> DRAWING INFORMATION
<br /> ACID RESISTANT WAIST PIPING ALL SIZES m
<br /> � REVISION DATE
<br /> PLUMBING VALVES & ACCESSORIES: 4. GLOBE VALVES: GLOBE VALVES SHALL BE EQUIPPED WITH RENEWABLE SEATING 7. STRAINERS: STRAINERS SHALL BE BRONZE BODY WYE-TYPE WITH STAINLESS STEEL 4-25-19
<br /> SURFACE (COMPOSITION DISC, RENEWABLE RING-SEAL). VALVES SHALL BE RISING STEM MESH 125 PSI SWP MINIMUM. J
<br /> 1. UNIONS: UNIONS ON FERROUS PIPE SHALL BE GROUND JOINT WITH BRASS TO IRON TYPE, BRONZE SCREWED END FOR FERROUS PIPING AND SOLDER END FOR COPPER FILE NAME:
<br /> SEATS AND UNIONS ON COPPER PIPING SHALL BE CAST BRONZE WITH SWEATS END. PIPING RATED FOR 125 PSI SWP. 8. PRESSURE GAUGES: GAUGES SHALL BE 4 J" DIAL, MICRO ADJUSTABLE POINTER,
<br /> 2. DIELECTRIC UNIONS: DISSIMILAR PIPE MATERIALS SHALL BE CONNECTED WITH 5. BALL VALVES: BALL VALVES SHALL BE EQUIPPED WITH TWO-PIECE BODY, SCREWED RING, FIBERGLASS REINFORCED POLYPROPYLENE CASE,PLEXIGLASS WINDOW, 19-0311 -YUMMY-DONUTS
<br /> DIELECTRIC PIPE FITTINGS/UNIONS RATED AT 250 PSIG AT 180F AND ARE DESIGNED TO CONVENTIONAL PART, BRONZE TRIM, TFE SEAT RINGS, AND BLOWOUT PROOF STEM. SOLID FRONT, BLOWOUT BACK AND SHALL DESIGNED THE GAUGE CAN BE LIQUID
<br /> MEET THE REQUIREMENTS OF ANSI 816.39, INCLUDING HYDROSTATIC STRENGTH, TENSILE CALVES SHALL BE RATED AT 125 SWP 400WOG AND MEET FEDERAL SPECIFICATIONS: FILLED THE FIELD BY THE ADDITION OFA A KIT WHERE VIBRATIONS A PROBLEM. DRAWING SCALE:
<br /> / ACCURACY 1% FULL SCALE, 0-200 PSI FOR DOMESTIC WATER SERVICE. TRERICE #450
<br /> STRENGTH, AND AIR PRESSURE TESTING. FITTINGS AND UNIONS SHALL BE WATTS 3000 WW-V-35, TYPE II, CLASS A, STYLE 3. OR APPROVED EQUAL BY ASHCROFT OR PALMER. EACH GAUGE SHALL BE PROVIDED WITH PROPOSED PLUMBING PLAN 1/4" = 1 '
<br /> SERIES OR APPROVED EQUAL BY DART, ROCKWOOD, OR WALWORTH. TRERICE # 735-2 NEEDLE VALVE COCK, 885-1 SYPHON, 872-2 SNUBBER.
<br /> 6. CHECK VALVES: SWING CHECK VALVES SHALL HAVE 45DEGREE SEATING ANGLE, DISC
<br /> 3. GATE VALVES: GATE VALVES SHALL BE BRONZE, RISING STEM TYPE, SCREWED END FOR SEAT ACCESS AND RENEWABLE SEATING. VALVES SHALL BE BRONZE, SCREWED END FOR 9_ NO EXPOSED ABS (PLASTIC PIPING WITH FLAME SPREAD RATING OF 75 OR MORE) SCALE: 1/4" = 1 '
<br /> FERROUS PIPING AND SOLDER END FOR COPPER PIPING, RATED FOR 125 PSI SWP. FERROUS PIPING AND SOLDER END FOR COPPER PIPING. SHALL BE EXPOSED UNDER SINKS OR ANYWHERE ELSE IN THE KITCHEN AREA. p 1
<br />
|