Laserfiche WebLink
UL/ULC Listed Red Thread® II A Piping System <br /> RED THREAD IIA PIPING <br /> RED THREAD IIA Primary Piping RED THREAD IIA Secondary Containment Piping <br /> Nom.Pipe Pipe Nom.Pipe Pipe <br /> Size Part Length Size Part Length <br /> (In./mm) Number (ft.) (InJimm) Number (ft.) <br /> 2 50 011020-069-1 15 3 80 011030-069-4 15 <br /> 2 50 011020-069-2 22-25 3 80 011030-059-5 22-25 <br /> 2 50 011020-069-3 26-30 3 80 011030-069-6 26-30 <br /> 3 80 011030-069-1 15 4 100 011040-077-5 15 <br /> 3 80 011030-069-2 22-25 4 100 011040-069-5 22-25 <br /> 3 80 011030-069-3 26-30 4 100 011040-077-6 26-30 <br /> 4 100 011040-071-1 '15 6 150 011060-120-5 15 <br /> 4 100 011040-069-2 22-25 6 150 011060-120-4 22-25 <br /> 4 100 011040-071-3 26-30 6 150 011060-120-6 26-30 <br /> DIMENSIONAL DATA <br /> Nominal Nominal Mill <br /> Pipe Nominal Nominal Wall Nominal Pressure/ Test External Pressure <br /> Size I.D. O.D. Thickness Weight Temperature Pressure Max.Rating(psig/MPa) <br /> (in./mm) (mJmm) (InJmm) (inJmm) (lbs.Atukg-n) Max.Rating (psig/MPa) 76°F/24°C 150°F/66°C <br /> 2 2.235 2.375 .070 0.5 250 psig @ 150°F 375 85 80 <br /> 50 57 61 1.78 0.74 1.72 MPa @ 66°C 2.59 .57 .55 <br /> 3 3.360 3.500 .070 0.7 175 psig @ 150°F 300 36 34 <br /> 80 85 90 2 54 1.04 1.21 MPa @ 66°C 2.07 25 23 <br /> 4 4.360 4.560 .085 1.2 125 psig @ 150°F 265 34 30 <br /> 100 111 116 2.16 1.79 0.86 MPa @ 66°C 1.83 .23 .21 <br /> 6 6.408 6.678 .135 2.4 NA 265 22 20 <br /> 150 163 170 3.43 3.51 NA 183 .15 .14 <br /> TYPICAL PHYSICAL PROPERTIES(') <br /> PROPERTY RED THREAD°IIA Pie Bending Radius,Minimum <br /> 24°C st ° ° <br /> MPa 150F MPa 66C Nominal <br /> psi�75°F � P �� � Pipe Size 2" 3" 4" 6" <br /> Axial Tensile(ASTM D2105) inches <br /> Ultimate Stress 10,300 71.0 8,200 56.5 <br /> Design Stress 2,575 17.8 2,050 14.1 Ft 75 110 140 204 <br /> Modulus of Elasticity 1.82 x 106 12548 1.42 x 106 9791 <br /> Axial Compression(ASTM D695) 33,300 230.0 25,600 177.0 m 21.3 33.5 42.7 62.2 <br /> Ultimate Stress 8,300 57.2 6,400 44 1 <br /> Design Stress 1.26 x 106 8687 .89 x 106 6136 <br /> Modulus of Elasticity <br /> (1) Allraluesexcept pressure-temperature <br /> Beam Bending(SFPTM) 159.0 19,200 132 0 maximum rating are nominal values.Tolerances or <br /> Ultimate Stress 23,000 maximurrdminimum limits can be obtained from Smith <br /> Design Stress(9 2,900 20.0 2,400 16.5 Fibercast <br /> Modulus of Elasticity 2.18 x 106 15031 1.70 x 106 11721 (2) All sizes can accept full vacuum pressures at <br /> (Long Term per ASTM D2925) maximum temperature ratings. <br /> (3) Ultimate and allowable design stresses are <br /> Hydrostatic Burst(ASTM D1599) based on minimum reinforced wall thickness.Pipe is <br /> Ultimate Hoop 34,000 234 39,200 271 manufactured in compliance with ASTM D2996. <br /> Tensile Stress (4) Design bending stress is 1/8 of ultimate to <br /> accountfor combined stress(i.e.bending and <br /> Hydrostatic Design(ASTM D2992) 2"-3" 2"&3" 2"&3" 2"&3" pressure). <br /> Procedure A 9,4100 64.91F, 7,4004) 510 (5) Design stress is based on long term cyclicfatigue <br /> Cyclic 150 x 106 4"-6" 4'-6" 4"-6" 4"-6" data using ASTM D2992 test method.However,all <br /> Cycles 13,0400 89.90 10,450 72.1 testing is not complete attime of printing. <br /> (6) For RED THREAD IIApipethe hydrostatic <br /> Coefficient of Linear 0.88 x 108 in fin 1°F cyclic design stress was determined at 150°and <br /> Thermal Expansion(SFPTM) 1.58 x 10arnm/mm/°C 200°F,per ASTM D2992 Procedure A Based on this <br /> data,the extrapolated value at75°F is 13030 psi. <br /> Specific Gravity 1.8 (7) For RED THREAD IIA pipe the hydrostatic cyclic <br /> Flow Factor design stress was determined at 75°and 200°F,per <br /> Hazen-Williams Coefficient 150 ASTM D2992 Procedure A Based on this data,the <br /> extrapolated value at 150`F is 7,400 psi. <br /> 4 <br />