|
PLUMBING SYMBOLS LEGEND
<br /> - G - GAS PIPING PLUMBING FIXTURE SCHEDULE KITCHEN FIXTURE SCHEDULE
<br /> -CD- CONDENSATE DRAIN PIPING COLD HOT VENT FILTERED
<br /> DESIGNATION MODEL NUMBER MFR. WATER WATER WASTE SIZE REMARKS DESIGNATION MFR. AND MODEL NUMBER COLD COLD HOT WASTE VENT REMARKS
<br /> - - - COLD WATER PIPING WATER CLOSET WATER WATER WATER SIZE
<br /> HOT WATER PIPING (140°) WATEK-361SET INTO PRE-CUT HOLE IN COUNTER. CONNECT CW BRAIDED STAINLESS TO
<br /> 18" HIGH BOWL CSEAT AND CAP BOLTS. 1.28 GAL PER
<br /> P-1 ADA COMPLIANT ELONGATED KOHLER /" - 4" 2" FLUSH INSTALL WITH ANGLE STOP. PROVIDE "WHITE"
<br /> -- - -- HOT WATER RECIRCULATING PIPING COLOR SELECTION FOR CHINA.
<br /> BOWL DIPPERWELL FAUCET& FAUCET AND PVC DRAIN TO WELL. PIPE DRAIN STRAIGHT BACK TO WALL, DOWN
<br /> -SAN- SANITARY WASTE PIPING P-4 SINK ASSEMBLY WALL, THEN FORWARD BETWEEN WHEELS OF ICE BIN BRACED TO FLOOR WITH
<br /> -FW- FILTERED WATER PIPING P-1A URINAL KOHLER 1-1/2" - 2" 2" VERIFY SPECS. & COLOR WITH OWNER. UNISTRUT AND A 1"AIR GAP OVER FLOOR SINK ivy
<br /> K-2590
<br /> -140'- 140°WATER PIPING PLUMBING CONTRACTOR TO PROVIDE 2" HW LINE WITH BALL VALVE SHUT-OFF.
<br /> -GVH GREASE WASTE PIPING DELTA FAUCET 501 LF-HGMHDF SINGLE LEVER WITH 0.5 RAPID RINSE STATION PROVIDE FINAL COLD WATER CONNECTION TO RAPID RINSE STATION. PROVIDE 3"
<br /> L 3 „ 4
<br /> ------ SANITARY VENT PIPING LAVATORY SINK
<br /> GPM VANDAL RESISTANT AERATOR, GRID STRAINER P-5 BY OWNER 4 INDIRECT WASTE LINE TO FLOOR SINK BELOW. PROVIDE RPZ IF REQUIRED BY
<br /> P-2 K-2030 KOHLER %" �" 2" 2" TAILPIECE, OFFSET WHEELCHAIR TRAP LOOSE KEY STOP. LOCAL CODE)
<br /> U_
<br /> VTR VENT THROUGH ROOF ADA COMPLIANT INSTALL HANDLE LIMIT STOP KIT WITHIN SINGLE LEVEL
<br /> �O PLUMBING TRAP MIXING FAUCET TO LIMIT OUTLET HOT WATER SUPPLY TO
<br /> 110°F.
<br /> N PIPE TURNING DOWN PLUMBING CONTRACTOR SHALL INSTALL WATER FILTER ESPRESSO MACHINE CONTRACTOR TO PROVIDE FW LINE WITH BRAIDED FLEX HOSE AND BALL
<br /> ----0 PIPE TURNING UP WATER FILTER SUPPLIED BY OWNER. PROVIDE WITH BALL ISOLATION EQ-1 (3 MACHINE GROUP+1 (4)�2„ (3)/4„ 2
<br /> o P-3 EVERPURE 1%" - - - OPTIONAL) VALVE SHUT-OFF. PROVIDE q" INDIRECT WASTE LINE TO FLOOR SINK BELOW.
<br /> C CHECK VALVE BY OWNER VALVE AND UNION ON BOTH ENDS OF ALL CONNECTIONS. TYPICAL OF 3 MACHINES IN GROUP.
<br /> co �~ PROVIDE RPZ WITH DRAIN CUP IF REQUIRED BY CODE. BY OWNER
<br /> ----iI1--- UNION 199,000 BTU TANKLESS WATER HEATER. PROVIDE T&P
<br /> o AFF ABOVE FINISHED FLOOR RELIEF VALVE, BRASS DRAIN VALVE FOAM INSULATION
<br /> P-6 (2)WATER HEATER RINNAI 1" 1" PER ASHRAE STANDARD, GAS PRESSURE REGULATOR
<br /> CO CLEAN OUT RUR1991N & RU199N AND ANODE ROD. PROVIDE AND INSTALL INTAKE AND
<br /> PRESSURE REGULATING VALVE (PRV) (50 PSI) EXHAUST AIR FLUES IN ACCORDANCE WITH
<br /> MANUFACTURE'S INSTALLATION INSTRUCTIONS. BUNN WATER DISPENSERCONTRACTOR TO PROVIDE FW WITH BALL VALVE SHUT-OFF. SUPPLIED WITH
<br /> BALL VALVE EQ-3 - (4)/2" - - - 2
<br /> BALANCE VALVE HAND SINK ADVANCE BY OWNER ASSE 1022 INLINE CARTRIDGE BACKFLOW. //��
<br /> GNICH
<br /> P-7 2" z" 2" 2" PROVIDED BY DBC, INSTALLED BY GC. ARCHITECTURE
<br /> a EWF ELECTRIC WATER FOUNTAIN 7-PS-56 TABCO
<br /> II
<br /> GCO GRADE CLEAN OUT PLUMBING CONTRACTOR TO PROVIDE 2" CW AND 2" HW v D I O
<br /> SUPPLY LINES WITH ANGLE VALVE SHUOFF AND SUPPLY AN OREGON LIMITED LIABILITY COMPANY
<br /> CIRCUIT SETTER BALANCE VALVE STOPS TO SINK FAUCET. PLUMBING CONTRACTOR TO EQ-4 GLASS FILLER (4)/2 _ _ _ 2" FILTER WATER SUPPLY- NO DRAIN REQUIRED
<br /> e P 8 3 COMPARTMENT SINK Y2 Y2 (3)2" - PROVIDE (3)2"WASTE LINES FROM EACH BAY AND BY OWNER
<br /> Q POINT OF CONNECTION BY OWNER
<br /> INDIRECT WASTE TO FLOOR SINK BELOW. PROVIDE
<br /> OF BELOW FLOOR FISHER 34271 FAUCET AND 24090 WASTE DRAIN WITH
<br /> STRAINERS, INSTALLED BY PC. CONTRACTOR TO PROVIDE z" FW LINE WITH BALL VALVE SHUT-OFF AND PROVIDE
<br /> o OC ABOVE CEILING FINAL COLD WATER CONNECTION TO ICE MACHINE. PROVIDE 4" INDIRECT WASTE 1001 SE SANDY BLVD, SUITE 100
<br /> 0 T&S EQ 8 ICE MACHINE _ (2)%2" _ %4" - LINE TO FLOOR SINK BELOW. BACKFLOW ON FILTER ASSEMBLY IF REQUIRED. PORTLAND, OR 97214
<br /> Q PUMP DISCHARGE P 9 PULL-OUT SPRAYER HANDLE (T&SBRASS. _ TO BE INSTALLED IN DB PROVIDED STAINLESS STEEL BY OWNER V. 503.552.9079
<br /> = MPZ-4DLN-06 COM) TABLE BY PC. NOTE: PC AND EC TO PROVIDE ADDITIONAL OUTLET AND WATERLINE STOP FOR
<br /> . FUTURE 2ND ICE MACHINE. F. 503.241.7055
<br /> 12
<br /> In GENERAL NOTES: WWW.GNICHARCH.COM
<br /> 1. EXACT LOCATION OF PLUMBING FIXTURES SHALL BE
<br /> DETERMINED FROM ARCHITECTURAL DRAWINGS. MOP SERVICE BASIN WITH 10" HIGH WALLS 3" DRAIN , FIAT
<br /> P-10 MOP SINK ZURN 4" %4" 3" 2" 830-AA SERVICE FAUCETS WITH VACUUM BREAKER, ICE STORAGE BIN s s O 1.13.21
<br /> 2. BEFORE SUBMITTING BID, THE PLUMBING CONTRACTOR 21996-24 INTEGRAL STOPS AND HOSE WITH HOSE BRACKET. EQ 9 BY OWNER - - - �4 - PROVIDE 4" INDIRECT WASTE LINE TO FLOOR SINK BELOW.
<br /> SHALL REVIEW THE ARCHITECTURAL DRAWINGS AND
<br /> INCLUDE IN HIS BID AN AMOUNT TO FURNISH AND INSTALL �E55lp
<br /> ANY FIXTURES WHICH ARE SHOWN IN ADDITION TO GENERAL NOTES: RG
<br /> cf�o FIXTURES SHOWN ON THE PLUMBING DRAWINGS. FLOOR SINK 12"X 12"X 6" DEEP CAST IRON BODY WITH WHITE 1. PLUMBING CONTRACTOR SHALL STRAP UP ALL SUPPLY LINES TIGHT TO STAINLESS TABLES WITH ZIPTIES SO THAT UNDER COUNTER EQUIPMENT CAN BE REMOVED �D r�,1� d�' �y
<br /> P-11 ZURN - - 4" 2"
<br /> = 3. CONTRACTOR SHALL VERIFY INVERT ELEVATION OF 21900 PORCELAIN ENAMEL WITHOUT GETTING CAUGHT IN THE BRAIDED STAINLESS SUPPLY LINES.
<br /> 2. PLUMBING CONTRACTOR SHALL RUN DRAINS OFF OF STAINLESS TABLES AND DRINK EQUIPMENT IN RIGID COPPER PIPE. DRAINS ARE TO BE RUN TOWARD THE
<br /> SEWERS TO WHICH NEW WASTE LINES ARE TO BE 2
<br /> CONNECTED BEFORE MAKING UP OR INSTALLATION OF NEW CENTER OF THE FLOOR SINK BENEATH EACH TABLE. DRAINS WILL FIT BETWEEN THE WHEELS OF THE ROLLING ICE BINS. PC TO STRAP DRAINS TO FLOOR WITH u� pl k
<br /> WASTE SYSTEM. POLISHED BRASS STRAINER, AND TRAP PRIMER. LOCATE UNISTRUT OR SIMILAR.
<br /> FL
<br /> FLOOR DRAIN
<br /> o P-12 ZURN - - 2" 2" PRIMER WITH SHUT-OFF VALVE AND ACCESS PANEL IN 3. ALL EXPOSED WATER LINES ARE TO BE RIGID COPPER. +�'� CHft O
<br /> Cli4. CONTRACTOR SHALL VERIFY AND COORDINATE LOCATION EZ-5 WALL. COORDINATE WITH GENERAL CONTRACTOR. 4. ALL SHUT OFF VALVES ARE TO BE COLORED BALL VALVES (DOMESTIC-BLUE, HOT-RED, FILTERED-WHITE)AND LABELED FOR EACH PIECE OF EQUIPMENT THAT IT gTRrOF C
<br /> a)
<br /> P414
<br /> M OF ALL PLUMBING LINES WITH DUCTWORK AND ELECTRICAL SUPPLIES. NO ANGLE STOPS.
<br /> E SERVICES. SCHIER GB-50 50GPM BELOW-GRADE AT EXTERIOR
<br /> P-13 GREASE INTERCEPTOR SCHIER - - 4" 2" VENTED THROUGH BUILDING, PROVIDE HI TRAFFIC
<br /> 5. THE INSTALLATION OF ALL VALVES, UNIONS, GB-50 COVER AND ACCESS. FINAL SIZE TO BE COORDINATED
<br /> THERMOMETERS, GAUGES, OR OTHER INDICATING OR WITH LOCAL AUTHORITY.
<br /> RECORDING EQUIPMENT, OR SPECIALTIES REQUIRING
<br /> o FREQUENT READING, REPAIRS, ADJUSTMENT, INSPECTION, ROOF DRAINREFER TO ARCHITECTURAL SHEET A4.0 FOR ROOF DRAIN
<br /> REMOVAL OR REPLACEMENT SHALL BE CONVENIENTLY AND P-14 2165 ZURN - - 3,. LOCATIONS AND DETAILS.
<br /> ACCESSIBLY LOCATED WITH REFERENCE TO THE FINISHED
<br /> BUILDING.
<br /> 6. WHERE POSSIBLE, THE VENTS TOGETHER SO THAT A WALL HYDRANT6" NON-FREEZE WALL HYDRANT, MOUNT AT 24"A.F.F. AT
<br /> MINIMUM NUMBER TERMINATE THROUGH THE ROOF. P-15 HY-420-8 WATTS 1/2" - - - REAR ELEVATION. 0
<br /> 7. WATER CLOSETS IN PUBLIC TOILET ROOMS SHALL CENTER �-
<br /> o ON THE FINAL LAYOUT OF TOILET PARTITIONS. Q) O
<br /> i N
<br /> ^° 8. ALL VENTS THROUGH ROOF SHALL BE AT LEAST 10' P-16 YARD HYDRANT WATTS 1/2" - - - FROST PROOF 2FT. BURY DEPTH O m
<br /> REMOVED FROM ALL AIR INTAKES, EVAP. COOLERS. EVERBILT
<br /> 10 9. CONTRACTOR SHALL NOT CUT HOLES IN STRUCTURAL
<br /> MEMBERS WITHOUT FIRST SECURING WRITTEN APPROVAL
<br /> a FROM ARCHITECT. RECIRCULATION PUMP
<br /> P-17 0010 TACO - - - - 115V, 3,25ORPM, PROVIDE W/AQUASTAT AND/OR TIMER O
<br /> 10.CONTRACTOR SHALL INSTALL DIELECTRIC UNIONS AT
<br /> CONNECTION OF DISSIMILAR METALS. FORMULA FOR SIZING GREASE INTERCEPTORS I-
<br /> 1 HP VARIABLE SPEED CONTROLLER, 115V INPUT, 30 GPM WATER PRESSURE CALCULATION
<br /> =
<br /> 11.CONTRACTOR SHALL ROUGH-IN ALL WASTE AND SUPPLIES BOOSTER PUMP O
<br /> TO SPECIAL EQUIP. ACCORDING TO MANUFACTURERS SHOP P-18 AQUAVAR BAQUABII AQUAVAR 1-1/4" - _ _ @ 35 PSI BOOST. PROVIDE ALL NECESSARY VALVES AND INTERIOR/EXTERIOR IN-FLOOR GREASE INTERCEPTORS
<br /> DRAWINGS AND MAKE FINAL CONNECTIONS ALL SUPPLIES 1151AB25HM03 ACCESSORIES RECOMMENDED BY MANUFACTURER FOR Length X Width X Depth/231= Gallons X .75 Fill Factor X Number of Compartments= Size of Grease Interceptor(GPM)
<br /> SHALL BE VALVED. A COMPLETE SYSTEM.
<br /> STATIC PRESSURE 60.0 Discharge from 3-Compartment Sink 3
<br /> 12.ASSUMED WATER PRESSURE-CONTRACTOR SHALL VERIFY
<br /> `° ACTUAL WATER PRESSURES PRIOR TO CONSTRUCTION. IF PRESSURE DROP THRU FRICTION LOSS FROM MAIN Compartment Deminsions: Q)
<br /> PRESSURE IS LESS THAN 60 PSI, CONTRACTOR SHALL TO METER(12"WATER LINE) 0 0 16" X 14" X 14" / 231 = 20 X .75 Fill Factor X 3 Compartments = 31 Gal z
<br /> CONTACT THE ENGINEER FOR PIPE SIZING EVALUATION. IF i
<br /> = PRESSURE EXCEEDS 80 PSI, A PRESSURE REDUCING VALVE PRESSURE DROP THRU METER 5.0 Total GPM / Retention Time O N `�
<br /> SHALL BE PROVIDED. PIPING VELOCITY SHALL NOT EXCEED 31 Gal / 1 Min = 31 GPM GREASE WASTE SIZE: 4" 4-
<br /> N
<br /> PRESSURE DROP THRU FRICTION LOSS FROM Q) Lx)
<br /> 8 FPS AND HOT WATER VELOCITY SHALL NOT EXCEED 5FPS. METER TO BACKFLOW 5.2 z � O
<br /> 01
<br /> 13.13ACKFLOW PREVENTION SHALL BE IN COMPLIANCE WITH PRESSURE DROP THRU BACKFLOW AND STRAINER 15.0 O '0 U
<br /> O `o
<br /> _0 MCPC SEC. 603. NUMBER OF FIXTURE TOTAL FIXTURES 2 DFU �� V)
<br /> FIXTURE x FIXTURES x VALUE UNIT UNITS / PER GPM = FLOW RATING GPM ' ` m
<br /> PRESSURE DROP DUE TO ELEVATION TO PUMP 4.3 v +=
<br /> � -, PRESSURE AVAILABLE @ PUMP 22.5
<br /> a) SANITARY SIZING CALCULATION Q� m
<br /> FIELD VERIFICATION NOTES: _ = 1 O U U
<br /> * FLOOR FIXTURES x 7 x 3 24 / 2 12
<br /> co 0' PRESSURE AVAILABLE AFTER PUMP 57.5 -�
<br /> 1. THE PLUMBING CONTRACTOR SHALL VISIT THE SITE PRIOR TO - - U �
<br /> BID TO FIELD VERIFY ALL EXISTING CONDITIONS WHICH MAY FIXTURE DESIGNATION DFU QUANTITY TOTAL HAND SINKS x 2 x 2 - 4 / 2 - 2.0 O U � 0
<br /> WASTE PRESSURE NEEDED AT FIXTURES 35.0 -�- O O
<br /> AFFECT HIS BID. THE FOLLOWING ITEMS SHALL BE VERIFIED. SERVICE BASIN x 1 x 3 = 3 / 2 = 1.5 N Q i O_
<br /> Q 1.A.EXACT PLACEMENT SIZE CAPACITY MANUFACTURER AND WATER CLOSET P-1 4 1 4 PRESSURE DROP DUE TO ELEVATION 4.0 0 LN 6E 42)
<br /> CONDITION OF ALL EXISTING PLUMBING EQUIPMENT WITHIN TOTAL REQUIRED FLOW RATING GPM = 46.5
<br /> SCOPE OF WORK, WHETHER SPECIFICALLY SHOWN OR NOT. REMAINING PRESSURE 26.5
<br /> 1.B.SIZE AND LOCATION OF ALL EXISTING WASTE, GREASE LAVATORY P-2 1 1 1 *FLOOR SINKS RECEIVING DISCHARGE FROM COMPARTMENT SINK(S), NOT COUNTED. REFER TO VOLUME CALCULATION FOR SINKS IN ISSUED FOR PERMIT.
<br /> S WASTE, VENT AND WATER PIPING. NATURAL RAL GAS SYSTEM LENGTH 150
<br /> THIS TABLE. � � . �3.202
<br /> CALCULATION
<br /> FLOOR DRAIN P-7 5 2 10 EQUIVALENT PIPE LENGTH 187.50 FT
<br /> 2. ALL REFERENCES ON THESE DRAWINGS TO EXISTING
<br /> EQUIPMENT, WATER IS THE RESPONSIBILITY OF THE 26.5PS1 X 10OFT
<br /> 15 15 CONTRACTOR TO VERIFY ALL THESE ITEMS PRIOR TO BID AND 3 COMP SINK P-14 6 1 6 APPLIANCES D(MMBHjD ALLOWABLE LOSS PER 100FT OF PIPE: 187.50 FT 14.1
<br /> INCLUDE IN HIS BID ANY AND ALL AMOUNTS REQUIRED TO
<br /> o Q ACCOMMODATE EXISTING CONDITIONS. FLOOR SINK P-4 6 6 36 RTU-1 115.0 FIXTURE UNITS DOMESTIC WATER
<br /> ._ ca-
<br /> F= RTU- 2115.0
<br /> 3. NO ALLOWANCES WILL BE MADE AFTER THE PROJECT HAS WATER HEATER 398.0 HOT EV: DATE: DESCRIPTION:
<br /> BEEN AWARDED FOR FAILURE TO VERIFY EXISTING
<br /> HAND SINK P-13 2 2 4 FIXTURES QUANTITY COLD WATER WATER
<br /> CONDITIONS. TOTAL BTU LOAD 628
<br /> MOP SINK P-3 3 1 3 HAND SINK 1 1 1
<br /> 0 0 4. ANY DISCREPANCIES WHICH MAY AFFECT THE CONTRACTORCZ
<br /> SYSTEM LENGTH 48
<br /> BID SHALL BE BROUGHT TO THE ATTENTION OF THE ENGINEER DEVELOPED PIPE LENGTH 60 LAVATORIES 1 1 1
<br /> = AND ARCHITECT FOR DIRECTION. PER 2019 CALIFORNIA PLUMBING CODE TOTAL (DFU) 64
<br /> WATER CLOSETS 1 2.5 0.0
<br /> 5. PLUMBING ROUTINGS BASED ON OWNER'S SCHEMATICS OF
<br /> KITCHEN SINK 2 6 6 SHEET NAME:
<br /> LOCATION OF EXISTING FIXTURES AND SHELL DRAWINGS.
<br /> o CONTRACTOR RESPONSIBLE FOR VERIFICATION OF ACTUAL MOP SINK 1 2 2
<br /> LOCATION OF SUPPLY LINES AND MAKING APPROPRIATE
<br /> PLUMBING
<br /> ADJUSTMENTS TO ACTUAL CONDITIONS IN THE FIELD. WATER DISPENSER 4 4 o SPECIFICATIONS &
<br /> 6. PRIOR TO CONSTRUCTION, VERIFY THE LOCATION OF THE ESPRESSO MACHINE (3 4 12 0.0 SCHEDULES
<br /> HVAC/WALK-IN CONDENSATE FLOOR SINK. IF SLOPE AND MACHINE GROUP)
<br /> co DISTANCE OR IF IT IS INFEASIBLE TO DISPOSE OF WALK-IN ICE MAKER 1 1.0 0.0
<br /> 0 COOLER CONDENSATE. USE A CONDENSATE PUMP.
<br /> m b RAPID RINSE 5 5.0 0.0 SHEET NUMBER:
<br /> CAtSE
<br /> o TOTAL 34.5000 10.0000 Engineering Inc. pl . 0
<br /> GPM 20 8
<br /> ID 796 Merus Court I T 636.349.1600
<br /> St.Louis,MO 63026 F 636.349.1730
<br /> 02020 DB Franchising USA,LLC
<br />
|