WORK PLANS - Laserfiche WebLink

Home Browse Search

1. MECHANICAL AND PLUMBING DETAILS APPLY TO ALL BUILDINGS WHETHER REFERENCED OR NOT. 2. PROVIDE FIRE STOPPING ASSEMBLY PROTECTION FOR DUCT PENETRATIONS OF RATED ASSEMBLIES. FIRE STOP RATING SHALL MATCH RATED ASSEMBLY BEING PENETRATED. 3. DUCTWORK AND PIPING SHALL NOT PENETRATE INTO OR THROUGH IT CLOSETS OR ELECTRICAL ROOM UNLESS IT SERVES THAT SPECIFIC ROOM. 4. REFERENCE ARCHITECTURAL DRAWINGS FOR EXACT LOCATION OF DIFFUSERS/GRILLES. 5. DRAWINGS SHALL BE CONSIDERED DIAGRAMMATIC. THE CONTRACTORS SHALL COORDINATE LOCATION OF ALL MECHANICAL DUCTWORK, EQUIPMENT, AND PIPING WITH ALL OTHER TRADES ON THIS PROJECT. 6. CEILING SUPPLY AIR DIFFUSERS TO HAVE 4 --WAY BLOW PATTERN UNLESS SHOWN OTHERWISE. 7. THERMOSTATS TO BE INSTALLED AT 46" AFF (TOP OF THERMOSTAT). DO NOT INSTALL THERMOSTATS OVER CASEWORK OR SHELVING OVER 24" IN DEPTH AND 34" IN HEIGHT. ALL MECHANICAL AND PLUMBING COMPONENTS SHALL BE ANCHORED AND INSTALLED PER THE DETAILS ON THE DSA APPROVED CONTRACT DOCUMENTS. WHERE NO DETAIL IS INDICATED, THE FOLLOWING COMPONENTS SHALL BE ANCHORED OR BRACED TO MEET THE FORCE AND DISPLACEMENT` REQUIREMENTS PRESCRIBED IN THE 2013 CBC, SECTION 1616A.1.18 THROUGH 1616A.1.26 AND ASCE 7--10, CHAPTERS IS, 16 AND 30. 1. ALL PERMANENT EQUIPMENT AND COMPONENTS 2. TEMPORARY OR MOVABLE EQUIPMENT THAT IS PERMANENTLY ATTACHED (E.G. HARD WIRED) TO THE BUILDING UTILITY SERVICES SUCH AS ELECTRICITY, GAS, OR WATER. 3. MOVABLE EQUIPMENT WHICH IS STATIONED IN ONE PLACE FOR MORE THAN 8 HOURS AND HEAVIER THAN 400 POUNDS ARE REQUIRED TO BE ANCHORED WITH TEMPORARY ATTACHMENTS. THE ATTACHMENT OF THE FOLLOWING MECHANICAL COMPONENTS SHALL BE POSITIVELY ATTACHED TO THE STRUCTURE, BUT NEED NOT BE DETAILED ON THE PLANS. THESE COMPONENTS SHALL HAVE FLEXIBLE CONNECTIONS PROVIDED BETWEEN THE COMPONENT AND ASSOCIATED DUCTWORK, PIPING, AND CONDUIT. A. COMPONENTS WEIGHING LESS THAN 400 POUNDS AND HAVE A CENTER OF MASS LOCATED 4 FEET OR LESS ABOVE THE ADJACENT FLOOR OR ROOF LEVEL THAT DIRECTLY SUPPORT THE COMPONENT. B. COMPONENTS WEIGHING LESS THAN 20 POUNDS, OR IN THE CASE OF DISTRIBUTED SYSTEMS, LESS THAN 5 POUNDS PER FOOT, WHICH ARE SUSPENDED FROM A ROOF OR FLOOR OR HUNG FROM A WALL. FOR THOSE ELEMENTS THAT DO NOT REQUIRE DETAILS ON THE APPROVED DRAWINGS, THE INSTALLATION SHALL BE SUBJECT TO THE APPROVAL OF THE STRUCTURAL ENGINEER OF RECORD AND THE DSA DISTRICT STRUCTURAL ENGINEER, THE PROJECT INSPECTOR WILL VERIFY THAT ALL COMPONENTS AND EQUIPMENT HAVE BEEN ANCHORED IN ACCORDANCE WITH THE ABOVE REQUIREMENTS. PIPING AND, DUCTWORK SYSTEM BRACING NOTE: PIPING AND DUCTWORK SHALL BE BRACED TO COMPLY THE FORCE AND DISPLACEMENTS PRESCRIBED IN ASCE 7-10 SECTION 13.3 AS DEFINED IN ASCE 7-10 SECTION 13.6.6, 13.6.7, AND 13.6.5.6, AND 2013 CBC, SECTIONS 1616A.1.23, 1616A.1.24, 1616A=1.25, AND 1615A.1.26. THE BRACING AND ATTACHMENT TO THE STRUCTURE SHALL BE DETAILED ON THE APPROVED DRAWINGS OR THEY SHALL COMPLY WITH ONE OF THE OSHPD PRE -APPROVALS (OPM #) AS MODIFIED TO SATISFY ANCHORAGE REQUIREMENTS OF AGI 316, APPENDIX D. COPIES OF THE MANUAL SHALL BE AVAILABLE ON THE JOBSITE PRIOR TO THE START OF HANDING AND BRACING OF THE PIPE AND DUCTWORK SYSTEMS. THE STRUCTURAL ENGINEER OF RECORD SHALL VERIFY THE ADEQUACY OF THE STRUCTURE TO SUPPORT THE HANGER AND BRACE LOADS. AIR CONDITIONING EXHAUST FAN SCHEDULE MANUFACTURER & MANUFACTURER & EXTERNAL SP SUPPLY AIR BLOWER HEATING CAPACITY (BTUH) MIM. COOLING CAPACITY MBH ARI CONDITIONS) HEATING CAPACITY (BTUH) MAXIMUM UNIT CONTROL INTERLOCK SCHEDULE SYMBOL MODEL NUMBER TOTAL CFM INCHES W.C.) MOTOR HP MOTOR BHP MOTOR RPM ELECTRICAL WEIGHT (LBS.) AC UNIT LIGHT SWITCH OUTSIDE AIR (CFM) DETECTOR WEIGHT ESP. NOTES NOMINAL DESIGN INTERLOCK INTERLOCK EF GREENHECK 1,200 0.375 1/2 0.12 HP 1,000 120V/10/60 Hz 125 AC/G1 G120 1G MODEL: CUE -161 -VG TOTAL SENSIBLE INPUT OUTPUT PHASE HERTZ VOLTS PHASE HERTZ MOCP EF 2G GREENHECK MODEL: CUE -099 -VG 425 0.375 1/4 0.05 AC 1,725 120V/10/60 Hz 100 AC/G2 G116 EF 3G GREENHECK MODEL: CUE -099 -VG 625 0.375 1/4 0.07 HEATING TO BE 8 STAGES FURNACE CONTROL (MIN.) 1,725 120V/10/60 Hz 100 AC/G3 G109 EF GREENHECK 1,200 0.375 1/2 0.12 25 1,000 120V/10/60 Hz 150 MAU/1G NA \4G7 MODEL: CUE -099 -VG STAGE = 2ND STAGE = 11.20 EER 208 30 60 40 SEE NOTE 4 NOT REQUIRED NOTES: COOLING (MIN) COOLING LISTED AT 2ND STAGE. PROVIDE WITH POWER 2. UNIT TO BE INTERLOCKED TO KITCHEN HOOD AND EXHAUST FAN 1. PROVIDE ROOF MOUNTED EXHAUST FANS WITH MANUFACTURER'S ROOF CURB. 3, UNIT TO BE PROVIDED WITH THE FOLLOWING: 2. LISTED MAXIMUM UNIT WEIGHT INCLUDES ALL ACCESSORIES (ROOF CURB, BIRDSCREENS, DAMPERS, ETC.). 1. MECHANICAL AND PLUMBING DETAILS APPLY TO ALL BUILDINGS WHETHER REFERENCED OR NOT. 2. PROVIDE FIRE STOPPING ASSEMBLY PROTECTION FOR DUCT PENETRATIONS OF RATED ASSEMBLIES. FIRE STOP RATING SHALL MATCH RATED ASSEMBLY BEING PENETRATED. 3. DUCTWORK AND PIPING SHALL NOT PENETRATE INTO OR THROUGH IT CLOSETS OR ELECTRICAL ROOM UNLESS IT SERVES THAT SPECIFIC ROOM. 4. REFERENCE ARCHITECTURAL DRAWINGS FOR EXACT LOCATION OF DIFFUSERS/GRILLES. 5. DRAWINGS SHALL BE CONSIDERED DIAGRAMMATIC. THE CONTRACTORS SHALL COORDINATE LOCATION OF ALL MECHANICAL DUCTWORK, EQUIPMENT, AND PIPING WITH ALL OTHER TRADES ON THIS PROJECT. 6. CEILING SUPPLY AIR DIFFUSERS TO HAVE 4 --WAY BLOW PATTERN UNLESS SHOWN OTHERWISE. 7. THERMOSTATS TO BE INSTALLED AT 46" AFF (TOP OF THERMOSTAT). DO NOT INSTALL THERMOSTATS OVER CASEWORK OR SHELVING OVER 24" IN DEPTH AND 34" IN HEIGHT. ALL MECHANICAL AND PLUMBING COMPONENTS SHALL BE ANCHORED AND INSTALLED PER THE DETAILS ON THE DSA APPROVED CONTRACT DOCUMENTS. WHERE NO DETAIL IS INDICATED, THE FOLLOWING COMPONENTS SHALL BE ANCHORED OR BRACED TO MEET THE FORCE AND DISPLACEMENT` REQUIREMENTS PRESCRIBED IN THE 2013 CBC, SECTION 1616A.1.18 THROUGH 1616A.1.26 AND ASCE 7--10, CHAPTERS IS, 16 AND 30. 1. ALL PERMANENT EQUIPMENT AND COMPONENTS 2. TEMPORARY OR MOVABLE EQUIPMENT THAT IS PERMANENTLY ATTACHED (E.G. HARD WIRED) TO THE BUILDING UTILITY SERVICES SUCH AS ELECTRICITY, GAS, OR WATER. 3. MOVABLE EQUIPMENT WHICH IS STATIONED IN ONE PLACE FOR MORE THAN 8 HOURS AND HEAVIER THAN 400 POUNDS ARE REQUIRED TO BE ANCHORED WITH TEMPORARY ATTACHMENTS. THE ATTACHMENT OF THE FOLLOWING MECHANICAL COMPONENTS SHALL BE POSITIVELY ATTACHED TO THE STRUCTURE, BUT NEED NOT BE DETAILED ON THE PLANS. THESE COMPONENTS SHALL HAVE FLEXIBLE CONNECTIONS PROVIDED BETWEEN THE COMPONENT AND ASSOCIATED DUCTWORK, PIPING, AND CONDUIT. A. COMPONENTS WEIGHING LESS THAN 400 POUNDS AND HAVE A CENTER OF MASS LOCATED 4 FEET OR LESS ABOVE THE ADJACENT FLOOR OR ROOF LEVEL THAT DIRECTLY SUPPORT THE COMPONENT. B. COMPONENTS WEIGHING LESS THAN 20 POUNDS, OR IN THE CASE OF DISTRIBUTED SYSTEMS, LESS THAN 5 POUNDS PER FOOT, WHICH ARE SUSPENDED FROM A ROOF OR FLOOR OR HUNG FROM A WALL. FOR THOSE ELEMENTS THAT DO NOT REQUIRE DETAILS ON THE APPROVED DRAWINGS, THE INSTALLATION SHALL BE SUBJECT TO THE APPROVAL OF THE STRUCTURAL ENGINEER OF RECORD AND THE DSA DISTRICT STRUCTURAL ENGINEER, THE PROJECT INSPECTOR WILL VERIFY THAT ALL COMPONENTS AND EQUIPMENT HAVE BEEN ANCHORED IN ACCORDANCE WITH THE ABOVE REQUIREMENTS. PIPING AND, DUCTWORK SYSTEM BRACING NOTE: PIPING AND DUCTWORK SHALL BE BRACED TO COMPLY THE FORCE AND DISPLACEMENTS PRESCRIBED IN ASCE 7-10 SECTION 13.3 AS DEFINED IN ASCE 7-10 SECTION 13.6.6, 13.6.7, AND 13.6.5.6, AND 2013 CBC, SECTIONS 1616A.1.23, 1616A.1.24, 1616A=1.25, AND 1615A.1.26. THE BRACING AND ATTACHMENT TO THE STRUCTURE SHALL BE DETAILED ON THE APPROVED DRAWINGS OR THEY SHALL COMPLY WITH ONE OF THE OSHPD PRE -APPROVALS (OPM #) AS MODIFIED TO SATISFY ANCHORAGE REQUIREMENTS OF AGI 316, APPENDIX D. COPIES OF THE MANUAL SHALL BE AVAILABLE ON THE JOBSITE PRIOR TO THE START OF HANDING AND BRACING OF THE PIPE AND DUCTWORK SYSTEMS. THE STRUCTURAL ENGINEER OF RECORD SHALL VERIFY THE ADEQUACY OF THE STRUCTURE TO SUPPORT THE HANGER AND BRACE LOADS. ITEM TO BE REMOVED / DEMOED RETURN OR EXHAUST AIR DUCT SUPPLY AIR DUCT FLEXIBLE CONNECTION ------- - �� BLV BALL VALVE BV. BALANCE VALVE BFV BUTTERFLY VALVE ---+�- CKV. CHECK VALVE THERMOMETER, PRESSURE GAUGE -;�-- OUTSIDE AIR INTO LOUVER -r---- RETURN OR EXHAUST AIR INTO REGISTER SUPPLY AIR FROM REGISTER EXHAUST AIR DUCT SECTION RETURN AIR DUCT SECTION SUPPLY AIR DUCT SECTION 12 x 10 DUCT FIRST FIGURE 510E SHOWN SECON FIGURE SIDE NOT SHOWN) SQUARE TO ROUND TRANSITION fF� TURNING VANES --� FLEXIBLE DUCTWORK VCD VCD ---�-' VOLUME CONTROL DAMPER R _ D_ RISE OR DROP IN DIRECTION OF ARROW SUPPLY AIR GRILLE ID ZE CFM RETURN AIR GRILLE ID -I -E-- FM EXHAUST AIR GRILLE ID .. !. ' rainarchitects forth ROOM THERMOSTAT (SEE MECHANICAL NOTES FOR MOUNTING HEIGHT) Yom' DIAMETER AC AIR CONDITIONING AD, AP ACCESS DOOR, ACCESS PANEL CC CENTER TO CENTER CFM,f CUBIC FEET OF AIR PER MINUTE (E), (N) EXISTING, NEW EA EXHAUST AIR EAD EXHAUST AIR DAMPER EF EXHAUST FAN `F DEGREES FAHRENHEIT FA / FB FROM ABOVE / FROM BELOW FD / FSD FIRE DAMPER / FIRE SMOKE DAMPER >; GA. GAUGE =' GALV. GALVANIZED ESTON GPM GALLONS PER MINUTE ASSOCIATES HP / 6HP HORSEPOWER / BREAK HORSEPOWER MAX., MIN. MAXIMUM, MINIMUM MECHANICAL ENGINEERS M.D. MANUAL DAMPER 4701 ANNE WAY k CARMICHAEL, CA 95608 1 (91 b) 4€ 2-0820 NA NOT APPLICABLE WESTON & ASSOCIATES #15012 NTS NOT TO SCALE pFESS�G� PRV. PRESSURE REDUCING VALVE e ®® A, pit E -le OA OUTSIDE AIR.y c� � No. M312 a u OAD OUTSIDE AIR DAMPER ' IRA RETURN AIR RENEWAL DATE: RAO RETURN AIR DAMPER v�'� v31t2015C�_- flA N RF RELIEF FAN SMS SHEET METAL SCREW SA, OA, SUPPLY AIR, OUTSIDE AIR TA / T8 TO ABOVE / TO BELOW T.C.V. TEMPERATURE CONTROL VALVE T.C.P. TEMPERATURE CONTROL PANEL TYP. TYPICAL $ ON/OFF SWITCH / STARTER ROOM NAME ROOM NAME AND NUMBER 0 ALL WORK PERFORMED UNDER THIS CONTRACT IS TO CONFIRM TO THE FOLLOWING CODES AND REGULATIONS: 1. CALIFORNIA ADMINISTRATIVE CODE, 2013 2. CALIFORNIA BUILDING CODE, 2013 3. CALIFORNIA MECHANICAL CODE, 2013 4. CALIFORNIA PLUMBING CODE, 2013 5. CALIFORNIA FIRE CODE, 2013 6. CALIFORNIA ELECTRICAL. CODE, 2013 7. CALIFORNIA ENERGY CODE, 2013 THE ABOVE CODES AND REGULATIONS REFER TO THE LATEST EDITION OR REVISION IF FORCE ON THE DATE OF THE CONTRACT, UNLESS OTHERWISE STATED. NOTHING ON THE DRAWINGS IS TO BE CONSTRUED AS REQUIRING OR PERMITTING WORK THAT IS CONTRARY TO THE LISTED CODES AND REGULATIONS, OR OTHER LOCAL, STATE OR FEDERAL CODES OR REGULATIONS WHICH MAY BE APPLICABLE. Copyright Q 2014 Rainforth Grau Architects. All rights reserved. Reproduction of ftse plans, either In whole or In part, Intruding any form of copying andfor proration of derlvaM works toed, for any reason vA#*ut prior wri ten permission, is Wcdy prol•rltaited, mu File tela.: 39-53 IDENTIFICATION STAMP DIV. OF THE STATE ARCHITECT 02-114490 INC. 1 AC r' FLSSS DATE i 1/ D )/jS- pr r::.� INCREMENT CAFETERIA MANTECAUNIFIED SCHOOL VIANTECA, CALIFORNIA MECHANICAL - LEGEND, SCHEDULES, AND NOTE] DRAW 4 DW PROJECT NO- CHECKED DATE DW SCALE SHEET 15-1207 06-26-15 AIR CONDITIONING UNIT SCHEDULE MADE-UP Alm"UNIT SCHEDULE SUPPLY AIR BLOWER MANUFACTURER & NOMINAL SUPPLY AIR BLOWER HEATING CAPACITY (BTUH) MIM. COOLING CAPACITY MBH ARI CONDITIONS) HEATING CAPACITY (BTUH) MINIMUM SYMBOL UNIT ELECTRICAL DATA MINIMUM DUCT SMOKE MAXIMUM UNIT SYMBOL MODEL NUMBER TONAGE EER / SEER OUTSIDE AIR (CFM) DETECTOR WEIGHT ESP. NOTES NOMINAL DESIGN FLA FLA FLA HP hHP TSP CFM MAXIMUM CFM bHP ESP LD8 TOTAL SENSIBLE INPUT OUTPUT PHASE HERTZ VOLTS PHASE HERTZ MOCP GREENHECK MODEL. IG -109-H12 1,200 (LBS.) 0.28 0.5 0.65 MIN. AC CARRIER CARRIER WEATHEREXPERT WEATHEREXPERT 79F 71'F 100,000 80,000 120 10 60 48 1ST STAGE = 248 1ST2ND IST STAGE = 200 00 HEATING TO BE 8 STAGES FURNACE CONTROL (MIN.) 27 PROVIDE WITH MEDIUM STATIC DRIVE UNIT TO HAVE 2 STAGES OF 1G MODEL: 2r3 25 10,000 10,000 5.94 1.2 305,9 231.8 STAGE = 2ND STAGE = 11.20 EER 208 30 60 40 SEE NOTE 4 NOT REQUIRED 3,500 COOLING (MIN) COOLING LISTED AT 2ND STAGE. PROVIDE WITH POWER 2. UNIT TO BE INTERLOCKED TO KITCHEN HOOD AND EXHAUST FAN EF/4G, UNIT TO OPERATE WHENEVER EF/4G IS ENABLED. 3, UNIT TO BE PROVIDED WITH THE FOLLOWING: EXHAUST - SEE NOTE 5 FOR DETAILS AC CARRIER WEATHEREXPERT 7.5 3,000 1.40 91.0 0.80 91.0 84,4 1 ST STAGE= 1200 1ST STAGE -_98 13.0 EER 208 310 60 36 500 REQUIRED 2,000 PROVIDE UNIT TO WITH MEDIUM STATIC DRIVE HAVE 3 STAGES OF COOLING (MIN) 2G MODEL: 48LCD-008 FILTERS, AND RECIRCULATING PUMP, 4. PROVIDE UNIT WITH A VENTSTAR MODEL T8850 PROGRAMMABLE THERMOSTAT. 2ND STAGE=150 2ND STAGE=120 45 COOLING LISTED AT 3RD STAGE AC 3G CARRIER WEATHEREXPERT MODEL: 48LCD-005 4 1,600 1,600 0.95 0.80 4.9.1 366 IST STAGE=50.0 2ND STAGE=72.0 1ST STAGE=41.0 2ND STAGE=56.0 16.4 SEER 208 30 60 27 40 625 NOT REQUIRED 1,200 UNIT TO COOLING HAVE 2 STAGES LISTED AT 2ND OF COOLING (MIN) STAGE NOTES: 1. SCHEDULED COOLING CAPACITIES ARE LISTED AT NOMINAL CFM (400 CFM/TON) AT ARI CONDITIONS - 95-F AMBIENT, 80-F DB /' 67°F WB. REFERENCE FLOORPLANS FOR ACTUAL DESIGN CFM AND BALANCE ACCORDINGLY. 2. PROVIDE ALL UNITS WITH THE FOLLOWING MANUFACTURER'S FACTORY INSTALLED OPTIONS / ACCESSORIES: - HINGED ACCESS PANELS - COIL GUARDS - 2" PLEATED FILTERS (MERV 13 FILTERS) - TXV VALVE - 0-1009 ENTHALPY ECONOMIZER WITH BAROMETRIC RELIEF. PROVIDE WITH JADE T24 COMPLIANT CONTROLLER. - CARRIER COMFORTLINK CONTROLS 3. PROVIDE EACH UNIT WITH A VENTSTAR MODEL T8850 PROGRAMMABLE THERMOSTAT. 4. AC/1G MINIMUM OUTSIDE AIR TO BE 1,200 WHEN CO2 IS SATISFIED. MINIMUM OUTSIDE AIR WHEN CO2 IS NOT SATISFIED TO BE 3,000 CFM 5. AC UNIT AC/IG TO BE PROVIDED WITH MICROMETAL PCD--HE34F-2MH POWER EXHAUST. POWER EXHAUST TO BE 23OV/30, MODULATING EXHAUST, EQUIPED WITH TWO 3 HP MOTORS AND CAPABLE OF EXHAUSTING 9,900 CFM AT 2" WC. POWER EXHAUST FLA = 17.6 ITEM TO BE REMOVED / DEMOED RETURN OR EXHAUST AIR DUCT SUPPLY AIR DUCT FLEXIBLE CONNECTION ------- - �� BLV BALL VALVE BV. BALANCE VALVE BFV BUTTERFLY VALVE ---+�- CKV. CHECK VALVE THERMOMETER, PRESSURE GAUGE -;�-- OUTSIDE AIR INTO LOUVER -r---- RETURN OR EXHAUST AIR INTO REGISTER SUPPLY AIR FROM REGISTER EXHAUST AIR DUCT SECTION RETURN AIR DUCT SECTION SUPPLY AIR DUCT SECTION 12 x 10 DUCT FIRST FIGURE 510E SHOWN SECON FIGURE SIDE NOT SHOWN) SQUARE TO ROUND TRANSITION fF� TURNING VANES --� FLEXIBLE DUCTWORK VCD VCD ---�-' VOLUME CONTROL DAMPER R _ D_ RISE OR DROP IN DIRECTION OF ARROW SUPPLY AIR GRILLE ID ZE CFM RETURN AIR GRILLE ID -I -E-- FM EXHAUST AIR GRILLE ID .. !. ' rainarchitects forth ROOM THERMOSTAT (SEE MECHANICAL NOTES FOR MOUNTING HEIGHT) Yom' DIAMETER AC AIR CONDITIONING AD, AP ACCESS DOOR, ACCESS PANEL CC CENTER TO CENTER CFM,f CUBIC FEET OF AIR PER MINUTE (E), (N) EXISTING, NEW EA EXHAUST AIR EAD EXHAUST AIR DAMPER EF EXHAUST FAN `F DEGREES FAHRENHEIT FA / FB FROM ABOVE / FROM BELOW FD / FSD FIRE DAMPER / FIRE SMOKE DAMPER >; GA. GAUGE =' GALV. GALVANIZED ESTON GPM GALLONS PER MINUTE ASSOCIATES HP / 6HP HORSEPOWER / BREAK HORSEPOWER MAX., MIN. MAXIMUM, MINIMUM MECHANICAL ENGINEERS M.D. MANUAL DAMPER 4701 ANNE WAY k CARMICHAEL, CA 95608 1 (91 b) 4€ 2-0820 NA NOT APPLICABLE WESTON & ASSOCIATES #15012 NTS NOT TO SCALE pFESS�G� PRV. PRESSURE REDUCING VALVE e ®® A, pit E -le OA OUTSIDE AIR.y c� � No. M312 a u OAD OUTSIDE AIR DAMPER ' IRA RETURN AIR RENEWAL DATE: RAO RETURN AIR DAMPER v�'� v31t2015C�_- flA N RF RELIEF FAN SMS SHEET METAL SCREW SA, OA, SUPPLY AIR, OUTSIDE AIR TA / T8 TO ABOVE / TO BELOW T.C.V. TEMPERATURE CONTROL VALVE T.C.P. TEMPERATURE CONTROL PANEL TYP. TYPICAL $ ON/OFF SWITCH / STARTER ROOM NAME ROOM NAME AND NUMBER 0 ALL WORK PERFORMED UNDER THIS CONTRACT IS TO CONFIRM TO THE FOLLOWING CODES AND REGULATIONS: 1. CALIFORNIA ADMINISTRATIVE CODE, 2013 2. CALIFORNIA BUILDING CODE, 2013 3. CALIFORNIA MECHANICAL CODE, 2013 4. CALIFORNIA PLUMBING CODE, 2013 5. CALIFORNIA FIRE CODE, 2013 6. CALIFORNIA ELECTRICAL. CODE, 2013 7. CALIFORNIA ENERGY CODE, 2013 THE ABOVE CODES AND REGULATIONS REFER TO THE LATEST EDITION OR REVISION IF FORCE ON THE DATE OF THE CONTRACT, UNLESS OTHERWISE STATED. NOTHING ON THE DRAWINGS IS TO BE CONSTRUED AS REQUIRING OR PERMITTING WORK THAT IS CONTRARY TO THE LISTED CODES AND REGULATIONS, OR OTHER LOCAL, STATE OR FEDERAL CODES OR REGULATIONS WHICH MAY BE APPLICABLE. Copyright Q 2014 Rainforth Grau Architects. All rights reserved. Reproduction of ftse plans, either In whole or In part, Intruding any form of copying andfor proration of derlvaM works toed, for any reason vA#*ut prior wri ten permission, is Wcdy prol•rltaited, mu File tela.: 39-53 IDENTIFICATION STAMP DIV. OF THE STATE ARCHITECT 02-114490 INC. 1 AC r' FLSSS DATE i 1/ D )/jS- pr r::.� INCREMENT CAFETERIA MANTECAUNIFIED SCHOOL VIANTECA, CALIFORNIA MECHANICAL - LEGEND, SCHEDULES, AND NOTE] DRAW 4 DW PROJECT NO- CHECKED DATE DW SCALE SHEET 15-1207 06-26-15 MADE-UP Alm"UNIT SCHEDULE SUPPLY AIR BLOWER EVAPORATIVE COOLING HEATING CAPACITY (BTUH) UNIT ELECTRICAL DATA MAXIMUM SYMBOL MANUFACTURER & MODEL NUMBER UNIT WEIGHT NOTES ESP. FLA FLA DESIGN CFM HP hHP TSP MIN. MBIA EDS EWB LD8 INPUT OUTPUT VOLTS PHASE HERTZ (LBS.) MAU 1 G GREENHECK MODEL. IG -109-H12 1,200 1/3 0.28 0.5 0.65 MIN. MBH 97'F 79F 71'F 100,000 80,000 120 10 60 16.5 20 1,200 HEATING TO BE 8 STAGES FURNACE CONTROL (MIN.) NOTES: 1. PROVIDE UNIT WITH 2" MERV 8 PLEATED FILTERS 2. UNIT TO BE INTERLOCKED TO KITCHEN HOOD AND EXHAUST FAN EF/4G, UNIT TO OPERATE WHENEVER EF/4G IS ENABLED. 3, UNIT TO BE PROVIDED WITH THE FOLLOWING: - ROOF CURB AND PEDESTAL MOUNT - HINGED ACCESS PANELS - PLEATED FILTERS (MERV 8 FILTERS) - EVAPORATIVE COOLING WITH CELDEK MEDIA, 2" ALUM. MESH FILTERS, AND RECIRCULATING PUMP, 4. PROVIDE UNIT WITH A VENTSTAR MODEL T8850 PROGRAMMABLE THERMOSTAT. ITEM TO BE REMOVED / DEMOED RETURN OR EXHAUST AIR DUCT SUPPLY AIR DUCT FLEXIBLE CONNECTION ------- - �� BLV BALL VALVE BV. BALANCE VALVE BFV BUTTERFLY VALVE ---+�- CKV. CHECK VALVE THERMOMETER, PRESSURE GAUGE -;�-- OUTSIDE AIR INTO LOUVER -r---- RETURN OR EXHAUST AIR INTO REGISTER SUPPLY AIR FROM REGISTER EXHAUST AIR DUCT SECTION RETURN AIR DUCT SECTION SUPPLY AIR DUCT SECTION 12 x 10 DUCT FIRST FIGURE 510E SHOWN SECON FIGURE SIDE NOT SHOWN) SQUARE TO ROUND TRANSITION fF� TURNING VANES --� FLEXIBLE DUCTWORK VCD VCD ---�-' VOLUME CONTROL DAMPER R _ D_ RISE OR DROP IN DIRECTION OF ARROW SUPPLY AIR GRILLE ID ZE CFM RETURN AIR GRILLE ID -I -E-- FM EXHAUST AIR GRILLE ID .. !. ' rainarchitects forth ROOM THERMOSTAT (SEE MECHANICAL NOTES FOR MOUNTING HEIGHT) Yom' DIAMETER AC AIR CONDITIONING AD, AP ACCESS DOOR, ACCESS PANEL CC CENTER TO CENTER CFM,f CUBIC FEET OF AIR PER MINUTE (E), (N) EXISTING, NEW EA EXHAUST AIR EAD EXHAUST AIR DAMPER EF EXHAUST FAN `F DEGREES FAHRENHEIT FA / FB FROM ABOVE / FROM BELOW FD / FSD FIRE DAMPER / FIRE SMOKE DAMPER >; GA. GAUGE =' GALV. GALVANIZED ESTON GPM GALLONS PER MINUTE ASSOCIATES HP / 6HP HORSEPOWER / BREAK HORSEPOWER MAX., MIN. MAXIMUM, MINIMUM MECHANICAL ENGINEERS M.D. MANUAL DAMPER 4701 ANNE WAY k CARMICHAEL, CA 95608 1 (91 b) 4€ 2-0820 NA NOT APPLICABLE WESTON & ASSOCIATES #15012 NTS NOT TO SCALE pFESS�G� PRV. PRESSURE REDUCING VALVE e ®® A, pit E -le OA OUTSIDE AIR.y c� � No. M312 a u OAD OUTSIDE AIR DAMPER ' IRA RETURN AIR RENEWAL DATE: RAO RETURN AIR DAMPER v�'� v31t2015C�_- flA N RF RELIEF FAN SMS SHEET METAL SCREW SA, OA, SUPPLY AIR, OUTSIDE AIR TA / T8 TO ABOVE / TO BELOW T.C.V. TEMPERATURE CONTROL VALVE T.C.P. TEMPERATURE CONTROL PANEL TYP. TYPICAL $ ON/OFF SWITCH / STARTER ROOM NAME ROOM NAME AND NUMBER 0 ALL WORK PERFORMED UNDER THIS CONTRACT IS TO CONFIRM TO THE FOLLOWING CODES AND REGULATIONS: 1. CALIFORNIA ADMINISTRATIVE CODE, 2013 2. CALIFORNIA BUILDING CODE, 2013 3. CALIFORNIA MECHANICAL CODE, 2013 4. CALIFORNIA PLUMBING CODE, 2013 5. CALIFORNIA FIRE CODE, 2013 6. CALIFORNIA ELECTRICAL. CODE, 2013 7. CALIFORNIA ENERGY CODE, 2013 THE ABOVE CODES AND REGULATIONS REFER TO THE LATEST EDITION OR REVISION IF FORCE ON THE DATE OF THE CONTRACT, UNLESS OTHERWISE STATED. NOTHING ON THE DRAWINGS IS TO BE CONSTRUED AS REQUIRING OR PERMITTING WORK THAT IS CONTRARY TO THE LISTED CODES AND REGULATIONS, OR OTHER LOCAL, STATE OR FEDERAL CODES OR REGULATIONS WHICH MAY BE APPLICABLE. Copyright Q 2014 Rainforth Grau Architects. All rights reserved. Reproduction of ftse plans, either In whole or In part, Intruding any form of copying andfor proration of derlvaM works toed, for any reason vA#*ut prior wri ten permission, is Wcdy prol•rltaited, mu File tela.: 39-53 IDENTIFICATION STAMP DIV. OF THE STATE ARCHITECT 02-114490 INC. 1 AC r' FLSSS DATE i 1/ D )/jS- pr r::.� INCREMENT CAFETERIA MANTECAUNIFIED SCHOOL VIANTECA, CALIFORNIA MECHANICAL - LEGEND, SCHEDULES, AND NOTE] DRAW 4 DW PROJECT NO- CHECKED DATE DW SCALE SHEET 15-1207 06-26-15