|
15 114 113 112 11 10 9 8 7 6 5 4 3 2 1
<br /> PLUMBING FIXTURE SCHEDULE PLUMBING GENERAL NOTES PLUMBING LEGEND
<br /> A MARK DESCRIPTION 1. SCOPE: SYMBOL ABBREVIATION DESCRIPTION A
<br /> WATER CLOSET: TWO-PIECE, FLOOR MOUNT, VITREOUS CHINA, WHITE, ELONGATED RIM, INTEGRAL TRAP, PROVIDE A COMPLETE DOMESTIC PLUMBING SYSTEM AS GENERALLY DELINEATED ON THE
<br /> FLUSH TANK, 1.0 GALLONS PER FLUSH, PRESSURE ASSISTED, 17 1/8" RIM HEIGHT, LEFT HAND TRIP LEVER. PLUMBING DRAWINGS, INCLUDING SERVICE PIPING AND FINAL CONNECTIONS TO EQUIPMENT
<br /> WC-1 KOHLER HIGHLINE K-3519.
<br /> FURNISHED AND INSTALLED BY OTHER TRADES AS MAY BE SHOWN ON THE ARCHITECTURAL, SS SOIL, WASTE OR SANITARY SEWER BELOW FLOOR
<br /> SEAT: HEAVY DUTY, ELONGATED, OPEN FRONT, STAINLESS STEEL SELF-SUSTAINING CHECK HINGES, ELECTRICAL OR OTHER DRAWINGS OF THE CONTRACT DOCUMENTS. PROVIDED DEMOLITION AS SS SOIL, WASTE OR SANITARY SEWER OVERHEAD
<br /> LESS COVER, KOHLER#K-4731. INSTALLED PER ADA REQUIREMENTS. GENERALLY DELINEATED ON THE PLUMBING PLANS. DEMOLISH AND REMOVE ALL UNUSED PIPING,
<br /> ABANDONED PIPING SHALL NOT BE ALLOWED. CAP PIPE AT BRANCH TEE. PATCH AND REPAIR ALL ----------- V VENT PIPING
<br /> THREE COMPARTMENT UTENSIL WASHING SINK- PROVIDED BY KITCHEN EQUIPMENT CONTRACTOR. MATCH ADJACENT SURFACES AND FINISHES. CW, ICW COLD WATER, INDUSTRIAL COLD WATER
<br /> SUPPLIES, STOPS AND CONNECTIONS BY PLUMBING CONTRACTOR. 2. CALIFORNIA CODE OF REGULATIONS: a rC 1 1 h
<br /> S-1 1 I tects
<br /> ALL HOT WATER DISTRIBUTION AND CIRCULATION LINES SHALL BE INSULATED IN ACCORDANCE - - HW, IHW(110°) HOT WATER SUPPLY, INDUSTRIAL HOT WATER
<br /> S-2
<br /> VEGETABLE/PREP SINK- PROVIDED BY KITCHEN EQUIPMENT CONTRACTOR. WITH SECTION 120.3 OF THE CALIFORNIA CODE OF REGULATIONS, TITLE 24, PART 6, SUBCHAPTER 3. HWR HOT WATER RETURN TIMOTHY P. HUFF &
<br /> B SUPPLIES, STOPS AND CONNECTIONS BY PLUMBING CONTRACTOR. 3. ALL PLUMBING FIXTURES & EQUIPMENT USED (E.G. SHOWERHEADS, LAVATORY FAUCETS, SINK B
<br /> FAUCET AND WATER HEATERS) SHALL BE CERTIFIED TO COMPLY WITH EFFICIENCY STANDARDS, AS (E) EXISTING TO BE REMOVEDASSOCIATES, I
<br /> S-3 BAR SINK- PROVIDED BY KITCHEN EQUIPMENT CONTRACTOR. LISTED BY THE CALIFORNIA ENERGY COMMISSION FOR SUCH APPLIANCES, BY ITS MANUFACTURER.
<br /> SUPPLIES, STOPS AND CONNECTIONS BY PLUMBING CONTRACTOR. D---OFIW D OR IW DRAIN OR INDIRECT WASTE Timothy P. Huff, AIA Architect
<br /> 4. CODES:
<br /> 519 McHenry Ave., Modesto, CA 95354
<br /> HAND WASHING SINK- PROVIDED BY KITCHEN EQUIPMENT CONTRACTOR. ALL WORK, MATERIAL, AND EQUIPMENT SHALL BE FURNISHED AND INSTALLED IN COMPLIANCE WITH CD CONDENSATE DRAIN Ph: (209)571-2232 Fax: (209) 571-1936
<br /> HS-1 THE FOLLOWING CODES AS ADOPTED AND AMENDED BY THE INSPECTING AUTHORITY HAVING
<br /> SUPPLIES, STOPS AND CONNECTIONS BY PLUMBING CONTRACTOR. INSTALL PER ADA REQUIREMENTS. JURISDICTION. NOTHING IN THESE PLANS IS TO BE CONSTRUED TO PERMIT THE INSTALLATION OF ��� OCD OVERFLOW CONDENSATE DRAIN
<br /> Geo ARCy
<br /> LAVATORY: UNDERMOUNT OVAL BASIN 18"x 14"x 5", ACRYLIC, ARCTIC WHITE, FRONT OVERFLOW, SOLID WORK, MATERIAL OR EQUIPMENT NOT CONFORMING TO THESE OR OTHER CODES APPLICABLE TO �
<br /> SURFACE FORMICA COUNTER TOP, PROVIDE SINGLE 1 1/4" HOLE, CUT COUNTER TOP TO LENGTH, FOLLOW THIS PROJECT. v� 01 PAO< ti �\
<br /> MANUFACTURER'S BASIN MOUNTING INSTRUCTIONS. FORMICA V065. A. 2019 CALIFORNIA ADMINISTRATIVE CODE (CAC), CALIFORNIA CODE OF REGULATIONS AD, AP ACCESS DOOR, ACCESS PANEL ; G�
<br /> FAUCET: BATTERY POWERED, INFRARED CONVERGENCE-TYPE SENSOR FAUCET, POLISHED CHROME, CAST (CCR)TITLE 24, PART 1.
<br /> L-1 BRASS BODY, IN-LINE FILTER, 0.5 GPM LAMINAR FLOW OUTLET, 4" FIXED CENTERS, 6"TALL x 6" SPOUT,
<br /> B. 2019 CALIFORNIA BUILDING CODE (CBC), CCR TITLE 24, PART 2, BASED ON THE 2018 AC AIR CHAMBER * No. C
<br /> C LEAD-FREE. ZURN Z6913-XL-N. INTERNATIONAL BUILDING CODE (IBC). 7 ANV ANGLE VALVE C N� 15527 Q
<br /> C. 2019 CALIFORNIA ELECTRICAL CODE (CEC), CCR TITLE 24, PART 3, BASED ON THE 2017 T y REN. 5/21
<br /> DRAIN: GRID STRAINER, OFFSET, W/OVERFLOW. ZURN 8743-PC. AQ AQUASTAT
<br /> PROVIDE P-TRAP, SUPPLIES, STOPS AND PROTECTIVE COVERS FOR P-TRAP& SUPPLIES. NATIONAL ELECTRICAL CODE (NEC). OF C PA\-\�
<br /> INSTALL PER ADA REQUIREMENTS. D. 2019 CALIFORNIA MECHANICAL CODE (CMC), CCR TITLE 24, PART 4, BASED ON THE 2018 ® AD AREA DRAIN
<br /> UNIFORM MECHANICAL CODE (UMC).
<br /> MOP SINK: CORNER, FLOOR MOUNT , PORCELAIN OVER CAST IRON, 28"x 28"x 12", 2" DRAIN. KOHLER K-6710 E. 2019 CALIFORNIA PLUMBING CODE (CPC), CCR TITLE 24, PART 5, BASED ON THE 2018 AAV AUTOMATIC AIR VENT Copyright 2021 -Timothy P. Huff&Associates
<br /> PROVIDE SINK RIM GUARD. KOHLER K-8940. UNIFORM PLUMBING CODE (UPC). BV BALL VALVE
<br /> MS-1 FAUCET: CHROME FINISH, 8" CENTERLINE, VACUUM BREAKER, INTEGRAL STOPS, WALL BRACE, PAIL HOOK, F. 2019 CALIFORNIA ENERGY CODE (CEC), CCR TITLE 24, PART 6.
<br /> 3/4" HOSE THREAD ON SPOUT, ZURN Z1996-SF. G. 2019 CALIFORNIA FIRE CODE (CFC), CCR TITLE 24, PART 9, BASED ON THE 2018 BRANCH -TOP CONNECTION BOUDREAU ENGINEERING, INC.
<br /> PROVIDE WITH MOP HANGER AND 4' LONG 3/4"0 FILL HOSE. INTERNATIONAL FIRE CODE (IFC) PO BOX 943
<br /> H. 2019 CALIFORNIA GREEN BUILDING STANDARDS CODE (CGBSC), CCR TITLE 24, PART11. BRANCH - BOTTOM CONNECTION MANTECA, CA 95336
<br /> FD-1 FLOOR DRAIN: CAST IRON BODY W/ACID RESISTANT EPDXY COATING, NICKEL BRONZE 6"0 W/ 1/4" HEEL 5. WORKMANSHIP: BRANCH -SIDE CONNECTION (209)606-7052
<br /> D PROOF TOP, NO-HUB 2" OUTLET, 1/2"TRAP PRIMER CONNECTION. ZURN Z416-6B-AR-P-2NH ALL WORK SHALL BE DONE IN A NEAT AND WORKMANLIKE MANNER ACCORDING TO THE BEST D
<br /> TRADE PRACTICE BY THOSE SKILLED IN THE PARTICULAR TRADE. EQUIPMENT, FIXTURES, PIPING, BFV BUTTERFLY VALVE CONSULTING MECHANICAL ENGINEERS
<br /> FS-1 FLOOR SINK: ENAMELED CAST IRON, ACID RESISTANT, 12"x 12"x 10" DEEP, 3/4 GRATE, 3" NO-HUB OUTLET, ETC., SHALL BE PLUMB, LEVEL, SQUARE AND/OR CENTERED, ETC. EQUIPMENT TO BE INSTALLED IN
<br /> ZURN #21902-3-3NH ] COP CAP ON END OF PIPE
<br /> FESS/ON
<br /> STRICT COMPLIANCE WITH MANUFACTURER'S RECOMMENDATIONS. QRO
<br /> FLOOR SINK: ENAMELED CAST IRON, ACID RESISTANT, 12"x 12"x 8" DEEP, 3/4 GRATE, 2" NO-HUB OUTLET, 6. EXISTING INFORMATION: CBV CALIBRATED BALANCE VALVE ��� B 0 UOgIF`
<br /> FS-2 ZURN #Z1901-3-2NH LOCATION, SIZE, ELEVATION, MATERIAL, ETC., OF EXISTING UTILITIES IS PROVIDED FROM SOURCES `� P _P
<br /> DEEMED RELIABLE BUT IS NOT GUARANTEED. THE CONTRACTOR SHALL FIELD VERIFY ALL DATA CB, RD CATCH BASIN, ROOF DRAIN �„
<br /> M3 z
<br /> BEFORE PROCEEDING WITH ANY WORK. NO EXTRA COST WILL BE ALLOWED FOR SERVICES NOT AS CKV CHECK VALVE 30, 021
<br /> SHOWN.
<br /> 7. PERMITS AND UTILITY SERVICE FEES: CP CIRCULATING PUMP �c
<br /> EQUIPMENT LIST THE PLUMBING CONTRACTOR SHALL ARRANGE AND PAY FOR ALL PERMITS, INSPECTIONS, AND CO X\CO CO CLEANOUT PLUGOHAN\"
<br /> SERVICE CHARGES REQUIRED FOR THE INSTALLATION OF THE WORK. F OF CM-\F0�
<br /> E 8. ACCURACY: ___D_ CR CONCENTRIC REDUCER E
<br /> MARK DESCRIPTION PLANS ARE DIAGRAMMATIC. THE CONTRACTOR SHALL CONFIRM ALL DIMENSIONS AND LOCATION
<br /> O DIA DIAMETER
<br /> STORAGE GAS WATER HEATER: COMMERCIAL eF SERIES, POWER DIRECT VENT, 125,000 BTU/HR
<br /> OF WALLS, PARTITIONS, FIXTURES, ETC., AGAINST DESIGN PLANS FOR CONSISTENCY AND
<br /> NATURAL GAS, 60 GALLON INSULATED STORAGE TANK, 180 GPH RECOVERY @ 80°F RISE, ACCURACY PRIOR TO COMMENCING WORK. ER ECCENTRIC REDUCER
<br /> WH-1 140° F. STORAGE TEMPERATURE. SHIPPING WT. = 570 LBS. OPERATING WEIGHT 1071 LBS. 9. PROVIDE AND INSTALL CONDENSATE DRAIN WITH TRAP AT EACH A/C UNIT PER THE CPC, AT FC FLEXIBLE CONNECTOR
<br /> BRADFORD WHITE MODEL EF-60T-125E-3N. INSTALL IN A POWER VENT CONFIGURATION. PROVIDE LOCATIONS SHOWN ON DRAWINGS. COORDINATE WORK WITH THE MECHANICAL CONTRACTOR.
<br /> APPROVED CATEGORY IV VENT WITH CONDENSATE DRAIN. INSTALL PER MANUFACTURER'S INSTRUCTIONS. 10. PROVIDE AND INSTALL ACCESS PANELS FOR ALL SHUT-OFF, ISOLATION, OR BRANCH VALVES NOT QI FCO FLOOR CLEANOUT
<br /> READILY ACCESSIBLE. ACCESS PANELS SHALL BE PROVIDED AND INSTALLED AT ALL TRAP PRIMER
<br /> CIRCULATION PUMP: LEAD-FREE BRONZE BODY, POLYPROPYLENE IMPELLER, CERAMIC SHAFT, 1/2" UNION VALVES AND WATER HAMMER ARRESTORS. FD FLOOR DRAIN
<br /> CP-1 CONNECTIONS, 4 GPM @ 6' HEAD, 115V/10, 41 WATTS @ 0.75 FLA, OP. WT. = 10 lbs, B&G#NBF-9U/LW. 11. ALL PIPING PASSING THROUGH CONCRETE FLOORS SHALL BE SLEEVED TO PROTECT PIPING FS FLOW SWITCH
<br /> PROVIDE WITH AQUASTAT AND AUTOMATIC TIMER. AGAINST BREAKAGE.
<br /> 12. HORIZONTAL DRAINAGE PIPING LESS THAN 4" IN DIAMETER SHALL BE SLOPED AT A MINIMUM OF 1/4" GCK GAGE COCK
<br /> F EXPANSION TANK: 6.4 GALLON TANK VOLUME, 0.50 ACCEPTANCE FACTOR, BUTYL DIAPHRAGM BLADDER, PER L.F. (2%) DRAINAGE PIPING 4"AND LARGER SHALL BE SLOPED AT A MINIMUM OF 1/8" PER L.F. GV GATE VALVE F
<br /> ET-1 WELDED STEEL CONSTRUCTION, 200°F MAX OPERATING TEMP., 150 PSIG MAX WORKING PRESSURE, 55 PSIG (1%).
<br /> FACTORY PRE-CHARGED, 12"0 x 14" HEIGHT, 3/4" SYSTEM CONNECTION, SHIPPING WT. 17 LBS. 13. ALL PLUMBING FIXTURES AND PIPING SHALL BE LISTED BY AN APPROVED LISTING AND TESTING GSCK, PC GAS COCK, PLUG COCK Consultants
<br /> AMTROL THERM-X-TROL#ST-12C. AGENCY AND PROPERLY LABELED.
<br /> 14. INSULATING MATERIALS APPLIED TO THE SURFACE OF DUCTS AND PIPES SHALL HAVE A FLAME GPR GAS PRESSURE REGULATOR
<br /> THERMOSTATIC MIXING VALVE: TEMPERATURE RANGE 60° TO 140°, LEAD FREE, 1/2" SWEAT CONNECTIONS & INDEX NOT TO EXCEED 25 AND ASMOKE-DEVELOPED INDEX NOT TO EXCEED 50 WHEN TESTED IN
<br /> TMV-1 CHECKS. SYMMONS MAXLINE#7-225-CK-MS-B-X. INSTALL PER MANUFACTURER'S RECOMMENDATIONS. GL. V. GLOBE VALVE
<br /> SHALL COMPLY WITH ASSE 1070/ASME Al 12.1070/CSA 8125.70. ACCORDANCE WITH ASTM E 84 OR UL 723, PER 2016 CMC, SECTION 604.
<br /> 15. ALL PIPE SHALL BE METAL. NO PLASTIC PIPE WILL BE ALLOWED.ALL PIPE PRODUCTS, INCLUDING VALVES GCO GRADE CLEANOUT
<br /> WALL ACCESS PANEL: 16 GAGE GALVANNEALED STEEL W/PRIME COAT FINISH, 12"X12"ACCESS DOOR MIN. , AND SIMILAR,SHALL BE OF LIKE MATERIAL. HB HOSE BIBB
<br /> AP-1 (SIZE TO SUIT APPLICATION), CYLINDER LOCK W/(2) KEYS, HINGED DOOR. ELMDOR "DW" SERIES-CL, 16. DISINFECT ALL DOMESTIC WATER PIPING PER 2019 CPC SECTION 609.9.
<br /> 17. PRESSURE TEST WATER PIPING PER 2019 CPC SECTION 609.4. NC NORMALLY CLOSED
<br /> G TRAP PRIMER: DIFFERENTIAL PRESSURE ACTIVATED, BRASS BODY, DISTRIBUTION MANIFOLD FOR 3 TRAPS, 18. PRESSURE TEST WASTE PIPING PER 2019 CPC SECTION 712.0. NO NORMALLY OPENED G ■ ■ N
<br /> TP-1 INSTALL STRICTLY PER MANUFACTURER'S RECOMMENDATIONS. PPP MODEL#P1-500 DU-4/DU-U.
<br /> PROVIDE ACCESS PANEL, SEE AP-1. AN PIPE ANCHOR W LU
<br /> PG PIPE GUIDE Uj Cn
<br /> POC POINT OF CONNECTION Z
<br /> CONNECTION PRV PRESSURE REDUCING VALVE LU ~ Q cnFIXT RE SCHED LE DEMOLITION NOTES
<br /> PG PRESSURE GAUGE Z = J
<br /> LU 0.FIXTURE WASTE COLD WATER HOT WATER �
<br /> SYM TRAP VENT 1. THE CONTRACTOR SHALL VISIT THE PROJECT SITE AND MAKE HIMSELF AWARE OF ALL EXISTING OR T&PR TEMPERATURE & PRESSURE RELIEF VALVE 0
<br /> BRANCH OUTLET BRANCH OUTLET BRANCH OUTLET CONDITIONS WHICH CAN BE OBSERVED. ADDITIONAL COSTS WILL NOT BE ALLOWED FOR
<br /> CORRECTION OF ITEMS WHICH CAN BE OBSERVED AND THEREFORE SHOULD BE INCLUDED IN HIS SV SOLENOID VALVE O W Cn 00 _
<br /> H WATER CLOSET WC 3" 3" -- 2" 3/4" 1/2" -- -- H
<br /> STRAINER V
<br /> THREE POT UTENSILE SINK S-1 2" 1 1/2" -- -- 1/2" 1/2" 1/2" 1/2" BID. THE CONTRACTOR IS RESPONSIBLE FOR ALL DEMOLITION WORK REQUIRED TO COMPLETE STIR THIS PROPOSED PROJECT. ~ �
<br /> VEGETABLE/PREP SINK S-2 2" 1 1/2" -- -- 1/2" 1/2" 1/2" 1/2" 2. THE NOTES AND DRAWINGS CONTAINED ON THIS SHEET DESCRIBE IN A GENERAL SENSE THE TH THERMOMETER O Z 0
<br /> EXTENT OF ITEMS TO BE MODIFIED, REMOVED OR INSTALLED. THIS DESCRIPTION DOES NOT ti
<br /> TP- TP TRAP PRIMER W Z W Z ch (n
<br /> BAR SINK S-3 2" 1 1/2" 1 1/2" 1 1/4" 1/2" 1/2" 1/2" 1/2" NECESSARILY INCLUDE A DESCRIPTION OF ITEMS TO BE REPAIRED OR REFINISHED AS A RESULT �/� M
<br /> 06
<br /> HAND WASHING FIXTURE HS 2" 1 1/4" 1 1/4" 1 1/4" 1/2" 1/2" 1/2" 1/2" OF THIS REMOVAL OR MODIFICATION. IN THE ABSENCE OF ANY SPECIFIC DIRECTION, THE ��� UN UNION OR FLANGE Cn W Lo LU
<br /> CONTRACTOR SHALL REPAIR THE AFFECTED AREA(S)TO A CONDITION EQUAL TO THE ADJACENT ♦�
<br /> LAVATORY L 2" 1 1/4" 1 1/4" 1 1/4" 1/2" 1/2" 1/2" 1/2" AREA(S)AND/OR SIMILAR EXISTING CONDITIONS ON PROJECT. WCO WALL CLEANOUT a �+/ LU U 0
<br /> MOP SINK Ms 3" 3" 3" 1 1/2" 3/4" 1/2" 3/4" 1/2" >
<br /> 3. THE CONTRACTOR SHALL PROVIDE DUST AND DEBRIS CONTROL THROUGHOUT THE PROJECT'S - Z
<br /> U V
<br /> CONSTRUCTION. THE CONTRACTOR SHALL COORDINATE HIS WORK WITH THE BUILDING OWNER UQ
<br /> FLOOR DRAIN FD 2" 2" 2" 1 1/2" -- -- -- -- TO PROVIDE THE LEAST INTERRUPTION OF EXISTING BUILDING OPERATIONS. COORDINATE WITH W M O Lu Z
<br /> FLOOR SINK FS-1 3" 3" 3" 1 1/2" -- -- -- -- THE OWNER THE LOCATION PATCHING
<br /> ON-SITESTORAGE
<br /> ESPECIND GING. PIPING MATERIAL SPECIFICATIONS I YQ.1 < LU
<br /> 4. NOT ALL REQUIRED PATCHING AND/OR REPAIRS ARE SPECIFICALLY NOTED ON THIS PLAN. Z
<br /> FLOOR SINK FS-2 2" 2" 2" 1 1/2" -- -- -- - 5. COORDINATE DEMOLITION WORK WITH NEW PROPOSED FLOOR PLANS.
<br /> 6. CONTRACTOR SHALL DISCARD AND DISPOSE OF ALL DEMOLISHED ITEMS. Q W W
<br /> TRAP PRIMER TP -- -- -- -- 1/2" 1/2" -- - A. DWV: SANITARY SEWAGE &VENT (SS &V) Q U Z J
<br /> 7. EXISTING PIPING AND ELECTRICAL OR COMMUNICATION CONDUITS WHICH INTERFERE WITH THE PIPE: SERVICE WEIGHT CAST IRON SOIL PIPE PER ASTM A-74 Lu Q
<br /> WORK SHALL BE RE-ROUTED BY THE CONTRACTOR. FITTINGS: CAST IRON "NO-HUB" PER CISPI 310
<br /> B. DOMESTIC WATER ABOVE GRADE: (CW, HW, HWR)
<br /> Q� z
<br /> PIPE: COPPER TYPE L PER ASTM B-88 O
<br /> SERVICE HOT WATER DEMAND FITTINGS: WROUGHT COPPER PER ANSI 16.22
<br /> Lu
<br /> GREEN BUILDING MEASURES INSULATION: INSULATE HOT WATER AND HOT WATER RETURNS: } 0
<br /> 1"0 AND LESS - 1" FIBERGLASS INSULATION W/ALL SERVICE JACKET. U-) J
<br /> SERVICE HOT WATER DEMAND: GREAT THAN 1"0 - 1 1/2" FIBERGLASS INSULATION W/ALL SERVICE JACKET. o-)
<br /> } J FOOD FACILITY SINGLE-SERVICE EATING UTENSILS - MINIMUM RECOVERY: 80% J U N a
<br /> GROUND WATER TEMP: 60°F 1. ALL PLUMBING FIXTURES SHALL MEET THE NONRESIDENTIAL MANDATORY MEASURES AS C. CONDENSATE DRAIN: (CD)
<br /> = STORAGE WATER TEMP.: 140°F PRESCRIBED IN THE CALIFORNIA GREEN BUILDING STANDARDS CODE (CGBSC). PIPE: COPPER TYPE L PER ASTM B-88
<br /> WATER HEATER:BRADFORD WHITE EF-60T-125E-3N, RECOVERY 180 GPH @ 80°F RISE, THERMAL 2• THE EFFECTIVE FLUSH VOLUME OF ALL WATER CLOSETS SHALL NOT EXCEED 1.28 GALLONS PER FITTINGS: WROUGHT COPPER PER ANSI 16.22 No. Description Date
<br /> O EFFICIENCY 96%. FLUSH (GPF). CGBSC 5.303.3.1.
<br /> it CALIFORNIA CONFERENCE OF DIRECTORS OF ENVIRONMENTAL HEALTH (CCDEH) 3. NONRESIDENTIAL LAVATORY FAUCETS. LAVATORY FAUCETS SHALL HAVE A MAXIMUM FLOW RATE
<br /> OF NOT MORE THAN 0.5 GPM AT 60 PSIG. 5.303.3.4.1
<br /> O
<br /> USAGE: 4. KITCHEN FAUCETS SHALL HAVE A MAXIMUM FLOW RATE OF NOT MORE THAN 1.8 GPM AT 60 PSIG.
<br /> N 3-COMP SINK 24"x24": 25 GPH/COMP x 3 , QTY 1 75 GPH KITCHEN FAUCETS MAY TEMPORARILY INCREASE THE FLOW ABOVE THE MAXIMUM RATE, BUT SHEET INDEX
<br /> U FOOD PREP SINK 24"x24": 5 GPH x 1, QTY 1 5 GPH NOT EXCEED 2.2 GPM AT 60 PSIG, AND MUST DEFAULT TO A MAXIMUM OF 1.8 GPM AT 60 PSIG.
<br /> 0 BAR: 6 GPH x 2, QTY 2 12 GPH CGBSC 5.303.3.4.2.
<br /> SHEET NO. DESCRIPTION
<br /> HAND WASH SINK: 5 GPH; QTY 2 10 GPH
<br /> U) K LAVATORY: 5 GPH, QTY 1 5 GPH P0.0 PLUMBING - LEGEND, NOTES AND SCHEDULES K
<br /> v JANITOR'S SINK: 15 GPH, QTY 1 15 GPH P1.1 PLUMBING - DEMOLITION FLOOR PLAN
<br /> O TOTAL 122 GPH
<br /> P2.1 PLUMBING - FLOOR PLAN
<br /> MINIMUM BTU/HR PER CCDEH = [(122 GPH x 0.8)x (140°F-60°F)x 8.33 LB/GAL]/(0.96) = 67,751 BTU/HR P5.1 PLUMBING - DETAILS
<br /> O HOT WATER DEMAND SUMMARY: Project Number 2008/BEI-21103
<br /> _ • WATER HEATER SPECIFIED HAS BTU/HR OUTPUT GREATER THAN REQUIRED BY CCDEH. Date AUGUST 2020
<br /> U WATER HEATER SPECIFIED HAS A HOURLY RECOVERY GREATER THAN REQUIRED BY CCDEH.
<br /> o Drawn by Author
<br /> Checked by Checker
<br /> 'pL L
<br /> N
<br /> 0
<br /> O P0 . 0
<br /> U
<br /> J
<br /> 0 Plot Date &Time 2/2/2021 9:33:03 AM
<br /> 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1
<br /> C:\Jobs\2021\21103- Manteca Senior Center\21103- MantecaSC- Plum b_20210215.dwg, 02/19/21 10:31:37 AM, AutoCAD PDF (High Quality Print).pc3
<br />
|